Kconfig 42.3 KB
Newer Older
1
#
2
# GPIO infrastructure and drivers
3
4
#

5
6
7
8
9
10
11
12
config ARCH_HAVE_CUSTOM_GPIO_H
	bool
	help
	  Selecting this config option from the architecture Kconfig allows
	  the architecture to provide a custom asm/gpio.h implementation
	  overriding the default implementations.  New uses of this are
	  strongly discouraged.

Michael Buesch's avatar
Michael Buesch committed
13
14
15
16
17
menuconfig GPIOLIB
	bool "GPIO Support"
	help
	  This enables GPIO support through the generic GPIO library.
	  You only need to enable this, if you also want to enable
18
	  one or more of the GPIO drivers below.
Michael Buesch's avatar
Michael Buesch committed
19
20

	  If unsure, say N.
21

Michael Buesch's avatar
Michael Buesch committed
22
if GPIOLIB
23

Laura Abbott's avatar
Laura Abbott committed
24
25
26
27
28
config GPIOLIB_FASTPATH_LIMIT
	int "Maximum number of GPIOs for fast path"
	range 32 512
	default 512
	help
29
30
	  This adjusts the point at which certain APIs will switch from
	  using a stack allocated buffer to a dynamically allocated buffer.
Laura Abbott's avatar
Laura Abbott committed
31

32
33
34
	  You shouldn't need to change this unless you really need to
	  optimize either stack space or performance. Change this carefully
	  since setting an incorrect value could cause stack corruption.
Laura Abbott's avatar
Laura Abbott committed
35

36
37
config OF_GPIO
	def_bool y
38
	depends on OF
39
	depends on HAS_IOMEM
40

Mathias Nyman's avatar
Mathias Nyman committed
41
42
43
44
config GPIO_ACPI
	def_bool y
	depends on ACPI

45
config GPIOLIB_IRQCHIP
46
	select IRQ_DOMAIN
47
48
	bool

49
50
51
52
53
config DEBUG_GPIO
	bool "Debug GPIO calls"
	depends on DEBUG_KERNEL
	help
	  Say Y here to add some extra checks and diagnostics to GPIO calls.
54
55
56
	  These checks help ensure that GPIOs have been properly initialized
	  before they are used, and that sleeping calls are not made from
	  non-sleeping contexts.  They can make bitbanged serial protocols
57
58
59
	  slower.  The diagnostics help catch the type of setup errors
	  that are most common when setting up new platforms or boards.

David Brownell's avatar
David Brownell committed
60
61
config GPIO_SYSFS
	bool "/sys/class/gpio/... (sysfs interface)"
62
	depends on SYSFS
David Brownell's avatar
David Brownell committed
63
64
65
66
67
68
69
70
71
72
73
74
	help
	  Say Y here to add a sysfs interface for GPIOs.

	  This is mostly useful to work around omissions in a system's
	  kernel support.  Those are common in custom and semicustom
	  hardware assembled using standard kernels with a minimum of
	  custom patches.  In those cases, userspace code may import
	  a given GPIO from the kernel, if no kernel driver requested it.

	  Kernel drivers may also request that a particular GPIO be
	  exported to userspace; this can be useful when debugging.

Grant Likely's avatar
Grant Likely committed
75
config GPIO_GENERIC
76
	depends on HAS_IOMEM # Only for IOMEM drivers
Grant Likely's avatar
Grant Likely committed
77
78
	tristate

79
# put drivers in the right section, in alphabetical order
80

81
# This symbol is selected by both I2C and SPI expanders
82
83
84
config GPIO_MAX730X
	tristate

85
menu "Memory mapped GPIO drivers"
86
	depends on HAS_IOMEM
87

88
89
90
91
92
93
94
95
96
97
98
99
100
101
config GPIO_74XX_MMIO
	tristate "GPIO driver for 74xx-ICs with MMIO access"
	depends on OF_GPIO
	select GPIO_GENERIC
	help
	  Say yes here to support GPIO functionality for 74xx-compatible ICs
	  with MMIO access. Compatible models include:
	    1 bit:	741G125 (Input), 741G74 (Output)
	    2 bits:	742G125 (Input), 7474 (Output)
	    4 bits:	74125 (Input), 74175 (Output)
	    6 bits:	74365 (Input), 74174 (Output)
	    8 bits:	74244 (Input), 74273 (Output)
	    16 bits:	741624 (Input), 7416374 (Output)

102
103
104
105
106
107
108
109
110
config GPIO_ALTERA
	tristate "Altera GPIO"
	depends on OF_GPIO
	select GPIOLIB_IRQCHIP
	help
	  Say Y or M here to build support for the Altera PIO device.

	  If driver is built as a module it will be called gpio-altera.

YD Tseng's avatar
YD Tseng committed
111
112
113
config GPIO_AMDPT
	tristate "AMD Promontory GPIO support"
	depends on ACPI
114
	select GPIO_GENERIC
YD Tseng's avatar
YD Tseng committed
115
116
117
118
	help
	  driver for GPIO functionality on Promontory IOHub
	  Require ACPI ASL code to enumerate as a platform device.

Joel Stanley's avatar
Joel Stanley committed
119
120
121
122
123
124
125
config GPIO_ASPEED
	tristate "Aspeed GPIO support"
	depends on (ARCH_ASPEED || COMPILE_TEST) && OF_GPIO
	select GPIOLIB_IRQCHIP
	help
	  Say Y here to support Aspeed AST2400 and AST2500 GPIO controllers.

126
127
128
config GPIO_ATH79
	tristate "Atheros AR71XX/AR724X/AR913X GPIO support"
	default y if ATH79
129
	depends on ATH79 || COMPILE_TEST
130
	select GPIO_GENERIC
131
	select GPIOLIB_IRQCHIP
132
133
134
135
	help
	  Select this option to enable GPIO driver for
	  Atheros AR71XX/AR724X/AR913X SoC devices.

136
137
138
139
config GPIO_RASPBERRYPI_EXP
	tristate "Raspberry Pi 3 GPIO Expander"
	default RASPBERRYPI_FIRMWARE
	depends on OF_GPIO
140
141
	# Make sure not 'y' when RASPBERRYPI_FIRMWARE is 'm'. This can only
	# happen when COMPILE_TEST=y, hence the added !RASPBERRYPI_FIRMWARE.
142
	depends on (ARCH_BCM2835 && RASPBERRYPI_FIRMWARE) || (COMPILE_TEST && !RASPBERRYPI_FIRMWARE)
143
144
145
146
	help
	  Turn on GPIO support for the expander on Raspberry Pi 3 boards, using
	  the firmware mailbox to communicate with VideoCore on BCM283x chips.

147
148
149
150
151
152
config GPIO_BCM_KONA
	bool "Broadcom Kona GPIO"
	depends on OF_GPIO && (ARCH_BCM_MOBILE || COMPILE_TEST)
	help
	  Turn on GPIO support for Broadcom "Kona" chips.

153
154
config GPIO_BRCMSTB
	tristate "BRCMSTB GPIO support"
155
156
	default y if (ARCH_BRCMSTB || BMIPS_GENERIC)
	depends on OF_GPIO && (ARCH_BRCMSTB || BMIPS_GENERIC || COMPILE_TEST)
157
	select GPIO_GENERIC
158
	select IRQ_DOMAIN
159
160
161
	help
	  Say yes here to enable GPIO support for Broadcom STB (BCM7XXX) SoCs.

Jan Kotas's avatar
Jan Kotas committed
162
163
164
165
166
167
168
169
config GPIO_CADENCE
	tristate "Cadence GPIO support"
	depends on OF_GPIO
	select GPIO_GENERIC
	select GPIOLIB_IRQCHIP
	help
	  Say yes here to enable support for Cadence GPIO controller.

170
config GPIO_CLPS711X
171
	tristate "CLPS711X GPIO support"
172
	depends on ARCH_CLPS711X || COMPILE_TEST
173
174
175
	select GPIO_GENERIC
	help
	  Say yes here to support GPIO on CLPS711X SoCs.
176

177
178
179
180
181
182
183
config GPIO_DAVINCI
	bool "TI Davinci/Keystone GPIO support"
	default y if ARCH_DAVINCI
	depends on ARM && (ARCH_DAVINCI || ARCH_KEYSTONE)
	help
	  Say yes here to enable GPIO support for TI Davinci/Keystone SoCs.

184
185
186
187
188
189
190
191
config GPIO_DWAPB
	tristate "Synopsys DesignWare APB GPIO driver"
	select GPIO_GENERIC
	select GENERIC_IRQ_CHIP
	help
	  Say Y or M here to build support for the Synopsys DesignWare APB
	  GPIO block.

192
193
194
195
196
197
198
199
config GPIO_EIC_SPRD
	tristate "Spreadtrum EIC support"
	depends on ARCH_SPRD || COMPILE_TEST
	depends on OF_GPIO
	select GPIOLIB_IRQCHIP
	help
	  Say yes here to support Spreadtrum EIC device.

Magnus Damm's avatar
Magnus Damm committed
200
201
config GPIO_EM
	tristate "Emma Mobile GPIO"
202
	depends on (ARCH_EMEV2 || COMPILE_TEST) && OF_GPIO
Magnus Damm's avatar
Magnus Damm committed
203
204
205
	help
	  Say yes here to support GPIO on Renesas Emma Mobile SoCs.

206
207
208
config GPIO_EP93XX
	def_bool y
	depends on ARCH_EP93XX
209
	select GPIO_GENERIC
210
	select GPIOLIB_IRQCHIP
211

212
213
214
215
216
217
218
config GPIO_EXAR
	tristate "Support for GPIO pins on XR17V352/354/358"
	depends on SERIAL_8250_EXAR
	help
	  Selecting this option will enable handling of GPIO pins present
	  on Exar XR17V352/354/358 chips.

219
220
221
222
223
224
225
226
227
228
229
230
config GPIO_GE_FPGA
	bool "GE FPGA based GPIO"
	depends on GE_FPGA
	select GPIO_GENERIC
	help
	  Support for common GPIO functionality provided on some GE Single Board
	  Computers.

	  This driver provides basic support (configure as input or output, read
	  and write pin state) for GPIO implemented in a number of GE single
	  board computers.

231
232
config GPIO_FTGPIO010
	bool "Faraday FTGPIO010 GPIO"
233
234
235
	depends on OF_GPIO
	select GPIO_GENERIC
	select GPIOLIB_IRQCHIP
236
	default (ARCH_GEMINI || ARCH_MOXART)
237
	help
238
239
	  Support for common GPIOs from the Faraday FTGPIO010 IP core, found in
	  Cortina systems Gemini platforms, Moxa ART and others.
240

241
242
243
244
245
246
247
248
config GPIO_GENERIC_PLATFORM
	tristate "Generic memory-mapped GPIO controller support (MMIO platform device)"
	select GPIO_GENERIC
	help
	  Say yes here to support basic platform_device memory-mapped GPIO controllers.

config GPIO_GRGPIO
	tristate "Aeroflex Gaisler GRGPIO support"
249
	depends on OF_GPIO
250
251
252
253
254
255
	select GPIO_GENERIC
	select IRQ_DOMAIN
	help
	  Select this to support Aeroflex Gaisler GRGPIO cores from the GRLIB
	  VHDL IP core library.

256
257
258
259
config GPIO_HLWD
	tristate "Nintendo Wii (Hollywood) GPIO"
	depends on OF_GPIO
	select GPIO_GENERIC
260
	select GPIOLIB_IRQCHIP
261
262
263
264
265
	help
	  Select this to support the GPIO controller of the Nintendo Wii.

	  If unsure, say N.

266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
config GPIO_ICH
	tristate "Intel ICH GPIO"
	depends on PCI && X86
	select MFD_CORE
	select LPC_ICH
	help
	  Say yes here to support the GPIO functionality of a number of Intel
	  ICH-based chipsets.  Currently supported devices: ICH6, ICH7, ICH8
	  ICH9, ICH10, Series 5/3400 (eg Ibex Peak), Series 6/C200 (eg
	  Cougar Point), NM10 (Tiger Point), and 3100 (Whitmore Lake).

	  If unsure, say N.

config GPIO_IOP
	tristate "Intel IOP GPIO"
281
282
	depends on ARCH_IOP32X || ARCH_IOP33X || COMPILE_TEST
	select GPIO_GENERIC
283
284
285
286
287
288
	help
	  Say yes here to support the GPIO functionality of a number of Intel
	  IOP32X or IOP33X.

	  If unsure, say N.

289
290
291
292
293
294
295
296
297
298
299
300
301
config GPIO_IXP4XX
	bool "Intel IXP4xx GPIO"
	depends on ARM # For <asm/mach-types.h>
	depends on ARCH_IXP4XX
	select GPIO_GENERIC
	select IRQ_DOMAIN
	select IRQ_DOMAIN_HIERARCHY
	help
	  Say yes here to support the GPIO functionality of a number of Intel
	  IXP4xx series of chips.

	  If unsure, say N.

302
303
304
305
306
307
config GPIO_LOONGSON
	bool "Loongson-2/3 GPIO support"
	depends on CPU_LOONGSON2 || CPU_LOONGSON3
	help
	  driver for GPIO functionality on Loongson-2F/3A/3B processors.

308
config GPIO_LPC18XX
309
	tristate "NXP LPC18XX/43XX GPIO support"
310
311
	default y if ARCH_LPC18XX
	depends on OF_GPIO && (ARCH_LPC18XX || COMPILE_TEST)
312
	select IRQ_DOMAIN_HIERARCHY
313
314
315
316
	help
	  Select this option to enable GPIO driver for
	  NXP LPC18XX/43XX devices.

317
318
319
320
321
322
323
324
config GPIO_LYNXPOINT
	tristate "Intel Lynxpoint GPIO support"
	depends on ACPI && X86
	select GPIOLIB_IRQCHIP
	help
	  driver for GPIO functionality on Intel Lynxpoint PCH chipset
	  Requires ACPI device enumeration code to set up a platform device.

325
config GPIO_MB86S7X
326
	tristate "GPIO support for Fujitsu MB86S7x Platforms"
327
328
329
	help
	  Say yes here to support the GPIO controller in Fujitsu MB86S70 SoCs.

330
331
332
333
334
config GPIO_MENZ127
	tristate "MEN 16Z127 GPIO support"
	depends on MCB
	select GPIO_GENERIC
	help
335
	  Say yes here to support the MEN 16Z127 GPIO Controller
336

337
338
339
340
341
342
343
344
config GPIO_MM_LANTIQ
	bool "Lantiq Memory mapped GPIOs"
	depends on LANTIQ && SOC_XWAY
	help
	  This enables support for memory mapped GPIOs on the External Bus Unit
	  (EBU) found on Lantiq SoCs. The gpios are output only as they are
	  created by attaching a 16bit latch to the bus.

345
346
347
348
config GPIO_MPC5200
	def_bool y
	depends on PPC_MPC52xx

349
config GPIO_MPC8XXX
350
	bool "MPC512x/MPC8xxx/QorIQ GPIO support"
351
	depends on PPC_MPC512x || PPC_MPC831x || PPC_MPC834x || PPC_MPC837x || \
352
353
354
		   FSL_SOC_BOOKE || PPC_86xx || ARCH_LAYERSCAPE || ARM || \
		   COMPILE_TEST
	select GPIO_GENERIC
Arnd Bergmann's avatar
Arnd Bergmann committed
355
	select IRQ_DOMAIN
356
357
	help
	  Say Y here if you're going to use hardware that connects to the
358
	  MPC512x/831x/834x/837x/8572/8610/QorIQ GPIOs.
359

360
361
362
config GPIO_MT7621
	bool "Mediatek MT7621 GPIO Support"
	depends on SOC_MT7620 || SOC_MT7621 || COMPILE_TEST
363
	depends on OF_GPIO
364
365
366
367
368
	select GPIO_GENERIC
	select GPIOLIB_IRQCHIP
	help
	  Say yes here to support the Mediatek MT7621 SoC GPIO device

369
370
config GPIO_MVEBU
	def_bool y
371
	depends on PLAT_ORION || ARCH_MVEBU
372
	depends on OF_GPIO
373
	select GENERIC_IRQ_CHIP
374
	select REGMAP_MMIO
375

376
377
378
config GPIO_MXC
	def_bool y
	depends on ARCH_MXC
Grant Likely's avatar
Grant Likely committed
379
	select GPIO_GENERIC
380
	select GENERIC_IRQ_CHIP
Grant Likely's avatar
Grant Likely committed
381
382
383
384

config GPIO_MXS
	def_bool y
	depends on ARCH_MXS
385
	select GPIO_GENERIC
386
	select GENERIC_IRQ_CHIP
387

388
389
390
391
392
393
394
395
config GPIO_OCTEON
	tristate "Cavium OCTEON GPIO"
	depends on GPIOLIB && CAVIUM_OCTEON_SOC
	default y
	help
	  Say yes here to support the on-chip GPIO lines on the OCTEON
	  family of SOCs.

396
config GPIO_OMAP
397
	tristate "TI OMAP GPIO support" if ARCH_OMAP2PLUS || COMPILE_TEST
398
	default y if ARCH_OMAP
399
400
	depends on ARM
	select GENERIC_IRQ_CHIP
401
	select GPIOLIB_IRQCHIP
402
403
404
	help
	  Say yes here to enable GPIO support for TI OMAP SoCs.

405
406
config GPIO_PL061
	bool "PrimeCell PL061 GPIO support"
407
	depends on ARM_AMBA
408
	select IRQ_DOMAIN
409
	select GPIOLIB_IRQCHIP
410
411
412
	help
	  Say yes here to support the PrimeCell PL061 GPIO device

413
414
415
416
417
418
419
420
config GPIO_PMIC_EIC_SPRD
	tristate "Spreadtrum PMIC EIC support"
	depends on MFD_SC27XX_PMIC || COMPILE_TEST
	depends on OF_GPIO
	select GPIOLIB_IRQCHIP
	help
	  Say yes here to support Spreadtrum PMIC EIC device.

421
422
423
424
425
426
config GPIO_PXA
	bool "PXA GPIO support"
	depends on ARCH_PXA || ARCH_MMP
	help
	  Say yes here to support the PXA GPIO device

427
428
config GPIO_RCAR
	tristate "Renesas R-Car GPIO"
Simon Horman's avatar
Simon Horman committed
429
	depends on ARCH_RENESAS || COMPILE_TEST
430
	select GPIOLIB_IRQCHIP
431
432
433
	help
	  Say yes here to support GPIO on Renesas R-Car SoCs.

434
435
436
437
438
439
config GPIO_REG
	bool
	help
	  A 32-bit single register GPIO fixed in/out implementation.  This
	  can be used to represent any register as a set of GPIO signals.

440
441
442
config GPIO_SAMA5D2_PIOBU
	tristate "SAMA5D2 PIOBU GPIO support"
	depends on MFD_SYSCON
443
	depends on OF_GPIO
444
445
446
447
448
449
450
451
	select GPIO_SYSCON
	help
	  Say yes here to use the PIOBU pins as GPIOs.

	  PIOBU pins on the SAMA5D2 can be used as GPIOs.
	  The difference from regular GPIOs is that they
	  maintain their value during backup/self-refresh.

452
453
454
455
456
457
458
459
config GPIO_SIOX
	tristate "SIOX GPIO support"
	depends on SIOX
	select GPIOLIB_IRQCHIP
	help
	  Say yes here to support SIOX I/O devices. These are units connected
	  via a SIOX bus and have a number of fixed-direction I/O lines.

460
461
462
config GPIO_SNPS_CREG
	bool "Synopsys GPIO via CREG (Control REGisters) driver"
	depends on ARC || COMPILE_TEST
463
	depends on OF_GPIO
464
465
466
467
468
469
	help
	  This driver supports GPIOs via CREG on various Synopsys SoCs.
	  This is a single-register MMIO GPIO driver for complex cases
	  where only several fields in register belong to GPIO lines and
	  each GPIO line owns a field with different length and on/off value.

470
471
472
473
474
475
476
config GPIO_SPEAR_SPICS
	bool "ST SPEAr13xx SPI Chip Select as GPIO support"
	depends on PLAT_SPEAR
	select GENERIC_IRQ_CHIP
	help
	  Say yes here to support ST SPEAr SPI Chip Select as GPIO device

477
478
479
480
481
482
483
484
config GPIO_SPRD
	tristate "Spreadtrum GPIO support"
	depends on ARCH_SPRD || COMPILE_TEST
	depends on OF_GPIO
	select GPIOLIB_IRQCHIP
	help
	  Say yes here to support Spreadtrum GPIO device.

485
486
487
488
489
490
491
492
config GPIO_STA2X11
	bool "STA2x11/ConneXt GPIO support"
	depends on MFD_STA2X11
	select GENERIC_IRQ_CHIP
	help
	  Say yes here to support the STA2x11/ConneXt GPIO device.
	  The GPIO module has 128 GPIO pins with alternate functions.

493
494
495
496
497
498
499
500
501
502
config GPIO_STP_XWAY
	bool "XWAY STP GPIOs"
	depends on SOC_XWAY
	help
	  This enables support for the Serial To Parallel (STP) unit found on
	  XWAY SoC. The STP allows the SoC to drive a shift registers cascade,
	  that can be up to 24 bit. This peripheral is aimed at driving leds.
	  Some of the gpios/leds can be auto updated by the soc with dsl and
	  phy status.

503
504
505
506
507
508
config GPIO_SYSCON
	tristate "GPIO based on SYSCON"
	depends on MFD_SYSCON && OF
	help
	  Say yes here to support GPIO functionality though SYSCON driver.

509
510
config GPIO_TB10X
	bool
Linus Walleij's avatar
Linus Walleij committed
511
	select GPIO_GENERIC
512
513
514
	select GENERIC_IRQ_CHIP
	select OF_GPIO

515
config GPIO_TEGRA
516
517
	bool "NVIDIA Tegra GPIO support"
	default ARCH_TEGRA
518
	depends on ARCH_TEGRA || COMPILE_TEST
519
	depends on OF_GPIO
520
521
	help
	  Say yes here to support GPIO pins on NVIDIA Tegra SoCs.
522

Thierry Reding's avatar
Thierry Reding committed
523
524
525
526
527
528
529
530
531
config GPIO_TEGRA186
	tristate "NVIDIA Tegra186 GPIO support"
	default ARCH_TEGRA_186_SOC
	depends on ARCH_TEGRA_186_SOC || COMPILE_TEST
	depends on OF_GPIO
	select GPIOLIB_IRQCHIP
	help
	  Say yes here to support GPIO pins on NVIDIA Tegra186 SoCs.

532
533
534
config GPIO_TS4800
	tristate "TS-4800 DIO blocks and compatibles"
	depends on OF_GPIO
535
	depends on SOC_IMX51 || COMPILE_TEST
536
537
538
539
	select GPIO_GENERIC
	help
	  This driver support TS-4800 FPGA GPIO controllers.

540
541
542
config GPIO_THUNDERX
	tristate "Cavium ThunderX/OCTEON-TX GPIO"
	depends on ARCH_THUNDER || (64BIT && COMPILE_TEST)
543
544
	depends on PCI_MSI
	select IRQ_DOMAIN_HIERARCHY
545
546
547
548
549
	select IRQ_FASTEOI_HIERARCHY_HANDLERS
	help
	  Say yes here to support the on-chip GPIO lines on the ThunderX
	  and OCTEON-TX families of SoCs.

550
551
552
553
554
555
556
557
config GPIO_UNIPHIER
	tristate "UniPhier GPIO support"
	depends on ARCH_UNIPHIER || COMPILE_TEST
	depends on OF_GPIO
	select IRQ_DOMAIN_HIERARCHY
	help
	  Say yes here to support UniPhier GPIOs.

558
559
560
561
562
563
564
config GPIO_VF610
	def_bool y
	depends on ARCH_MXC && SOC_VF610
	select GPIOLIB_IRQCHIP
	help
	  Say yes here to support Vybrid vf610 GPIOs.

565
566
567
568
569
570
571
572
config GPIO_VR41XX
	tristate "NEC VR4100 series General-purpose I/O Uint support"
	depends on CPU_VR41XX
	help
	  Say yes here to support the NEC VR4100 series General-purpose I/O Uint

config GPIO_VX855
	tristate "VIA VX855/VX875 GPIO"
573
	depends on (X86 || COMPILE_TEST) && PCI
574
575
576
577
578
579
580
581
582
	select MFD_CORE
	select MFD_VX855
	help
	  Support access to the VX855/VX875 GPIO lines through the gpio library.

	  This driver provides common support for accessing the device,
	  additional drivers must be enabled in order to use the
	  functionality of the device.

583
584
585
586
587
588
589
590
591
config GPIO_XGENE
	bool "APM X-Gene GPIO controller support"
	depends on ARM64 && OF_GPIO
	help
	  This driver is to support the GPIO block within the APM X-Gene SoC
	  platform's generic flash controller. The GPIO pins are muxed with
	  the generic flash controller's address and data pins. Say yes
	  here to enable the GFC GPIO functionality.

592
593
594
595
config GPIO_XGENE_SB
	tristate "APM X-Gene GPIO standby controller support"
	depends on ARCH_XGENE && OF_GPIO
	select GPIO_GENERIC
596
	select GPIOLIB_IRQCHIP
597
	select IRQ_DOMAIN_HIERARCHY
598
599
600
601
	help
	  This driver supports the GPIO block within the APM X-Gene
	  Standby Domain. Say yes here to enable the GPIO functionality.

602
config GPIO_XILINX
603
	tristate "Xilinx GPIO support"
604
	depends on OF_GPIO
605
606
607
	help
	  Say yes here to support the Xilinx FPGA GPIO device

608
609
config GPIO_XLP
	tristate "Netlogic XLP GPIO support"
610
	depends on OF_GPIO && (CPU_XLP || ARCH_THUNDER2 || COMPILE_TEST)
611
612
613
614
	select GPIOLIB_IRQCHIP
	help
	  This driver provides support for GPIO interface on Netlogic XLP MIPS64
	  SoCs. Currently supported XLP variants are XLP8XX, XLP3XX, XLP2XX,
615
616
	  XLP9XX and XLP5XX. The same GPIO controller block is also present in
	  Cavium's ThunderX2 CN99XX SoCs.
617
618
619

	  If unsure, say N.

Baruch Siach's avatar
Baruch Siach committed
620
621
622
config GPIO_XTENSA
	bool "Xtensa GPIO32 support"
	depends on XTENSA
623
	depends on HAVE_XTENSA_GPIO32
Baruch Siach's avatar
Baruch Siach committed
624
625
626
627
628
	depends on !SMP
	help
	  Say yes here to support the Xtensa internal GPIO32 IMPWIRE (input)
	  and EXPSTATE (output) ports

629
630
631
config GPIO_ZEVIO
	bool "LSI ZEVIO SoC memory mapped GPIOs"
	depends on ARM && OF_GPIO
632
	help
633
	  Say yes here to support the GPIO controller in LSI ZEVIO SoCs.
634

635
636
config GPIO_ZYNQ
	tristate "Xilinx Zynq GPIO support"
637
	depends on ARCH_ZYNQ || ARCH_ZYNQMP
638
	select GPIOLIB_IRQCHIP
639
	help
640
	  Say yes here to support Xilinx Zynq GPIO controller.
641

Linus Walleij's avatar
Linus Walleij committed
642
643
config GPIO_ZX
	bool "ZTE ZX GPIO support"
Peter Robinson's avatar
Peter Robinson committed
644
	depends on ARCH_ZX || COMPILE_TEST
Linus Walleij's avatar
Linus Walleij committed
645
646
647
648
	select GPIOLIB_IRQCHIP
	help
	  Say yes here to support the GPIO device on ZTE ZX SoCs.

649
650
651
652
653
654
655
config GPIO_LOONGSON1
	tristate "Loongson1 GPIO support"
	depends on MACH_LOONGSON32
	select GPIO_GENERIC
	help
	  Say Y or M here to support GPIO on Loongson1 SoCs.

656
657
658
659
660
661
662
663
664
config GPIO_AMD_FCH
	tristate "GPIO support for AMD Fusion Controller Hub (G-series SOCs)"
	help
	  This option enables driver for GPIO on AMDs Fusion Controller Hub,
	  as found on G-series SOCs (eg. GX-412TC)

	  Note: This driver doesn't registers itself automatically, as it
	  needs to be provided with platform specific configuration.
	  (See eg. CONFIG_PCENGINES_APU2.)
665
endmenu
666

667
menu "Port-mapped I/O GPIO drivers"
668
	depends on X86 # Unconditional I/O space access
669

670
671
config GPIO_104_DIO_48E
	tristate "ACCES 104-DIO-48E GPIO support"
672
673
	depends on PC104
	select ISA_BUS_API
674
675
	select GPIOLIB_IRQCHIP
	help
676
677
678
679
	  Enables GPIO support for the ACCES 104-DIO-48E series (104-DIO-48E,
	  104-DIO-24E). The base port addresses for the devices may be
	  configured via the base module parameter. The interrupt line numbers
	  for the devices may be configured via the irq module parameter.
680

681
682
config GPIO_104_IDIO_16
	tristate "ACCES 104-IDIO-16 GPIO support"
683
684
	depends on PC104
	select ISA_BUS_API
685
	select GPIOLIB_IRQCHIP
686
	help
687
688
689
690
691
	  Enables GPIO support for the ACCES 104-IDIO-16 family (104-IDIO-16,
	  104-IDIO-16E, 104-IDO-16, 104-IDIO-8, 104-IDIO-8E, 104-IDO-8). The
	  base port addresses for the devices may be configured via the base
	  module parameter. The interrupt line numbers for the devices may be
	  configured via the irq module parameter.
692

693
694
config GPIO_104_IDI_48
	tristate "ACCES 104-IDI-48 GPIO support"
695
696
	depends on PC104
	select ISA_BUS_API
697
698
	select GPIOLIB_IRQCHIP
	help
699
700
701
702
703
	  Enables GPIO support for the ACCES 104-IDI-48 family (104-IDI-48A,
	  104-IDI-48AC, 104-IDI-48B, 104-IDI-48BC). The base port addresses for
	  the devices may be configured via the base module parameter. The
	  interrupt line numbers for the devices may be configured via the irq
	  module parameter.
704

705
config GPIO_F7188X
706
	tristate "F71869, F71869A, F71882FG, F71889F and F81866 GPIO support"
707
708
	help
	  This option enables support for GPIOs found on Fintek Super-I/O
709
	  chips F71869, F71869A, F71882FG, F71889F and F81866.
710
711
712
713

	  To compile this driver as a module, choose M here: the module will
	  be called f7188x-gpio.

714
715
config GPIO_GPIO_MM
	tristate "Diamond Systems GPIO-MM GPIO support"
716
717
	depends on PC104
	select ISA_BUS_API
718
719
720
721
722
723
724
725
726
727
	help
	  Enables GPIO support for the Diamond Systems GPIO-MM and GPIO-MM-12.

	  The Diamond Systems GPIO-MM device features 48 lines of digital I/O
	  via the emulation of dual 82C55A PPI chips. This driver provides GPIO
	  support for these 48 channels of digital I/O.

	  The base port addresses for the devices may be configured via the base
	  array module parameter.

728
729
730
731
732
733
config GPIO_IT87
	tristate "IT87xx GPIO support"
	help
	  Say yes here to support GPIO functionality of IT87xx Super I/O chips.

	  This driver is tested with ITE IT8728 and IT8732 Super I/O chips, and
734
735
	  supports the IT8761E, IT8613, IT8620E, and IT8628E Super I/O chips as
	  well.
736
737
738
739
740
741

	  To compile this driver as a module, choose M here: the module will
	  be called gpio_it87

config GPIO_SCH
	tristate "Intel SCH/TunnelCreek/Centerton/Quark X1000 GPIO"
742
	depends on (X86 || COMPILE_TEST) && PCI
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
	select MFD_CORE
	select LPC_SCH
	help
	  Say yes here to support GPIO interface on Intel Poulsbo SCH,
	  Intel Tunnel Creek processor, Intel Centerton processor or
	  Intel Quark X1000 SoC.

	  The Intel SCH contains a total of 14 GPIO pins. Ten GPIOs are
	  powered by the core power rail and are turned off during sleep
	  modes (S3 and higher). The remaining four GPIOs are powered by
	  the Intel SCH suspend power supply. These GPIOs remain
	  active during S3. The suspend powered GPIOs can be used to wake the
	  system from the Suspend-to-RAM state.

	  The Intel Tunnel Creek processor has 5 GPIOs powered by the
	  core power rail and 9 from suspend power supply.

	  The Intel Centerton processor has a total of 30 GPIO pins.
	  Twenty-one are powered by the core power rail and 9 from the
	  suspend power supply.

	  The Intel Quark X1000 SoC has 2 GPIOs powered by the core
	  power well and 6 from the suspend power well.

config GPIO_SCH311X
	tristate "SMSC SCH311x SuperI/O GPIO"
	help
	  Driver to enable the GPIOs found on SMSC SMSC SCH3112, SCH3114 and
	  SCH3116 "Super I/O" chipsets.

	  To compile this driver as a module, choose M here: the module will
	  be called gpio-sch311x.

config GPIO_TS5500
	tristate "TS-5500 DIO blocks and compatibles"
	depends on TS5500 || COMPILE_TEST
	help
	  This driver supports Digital I/O exposed by pin blocks found on some
	  Technologic Systems platforms. It includes, but is not limited to, 3
	  blocks of the TS-5500: DIO1, DIO2 and the LCD port, and the TS-5600
	  LCD port.

785
786
config GPIO_WINBOND
	tristate "Winbond Super I/O GPIO support"
787
	select ISA_BUS_API
788
789
790
791
792
793
794
795
796
797
798
799
800
	help
	  This option enables support for GPIOs found on Winbond Super I/O
	  chips.
	  Currently, only W83627UHG (also known as Nuvoton NCT6627UD) is
	  supported.

	  You will need to provide a module parameter "gpios", or a
	  boot-time parameter "gpio_winbond.gpios" with a bitmask of GPIO
	  ports to enable (bit 0 is GPIO1, bit 1 is GPIO2, etc.).

	  To compile this driver as a module, choose M here: the module will
	  be called gpio-winbond.

801
802
config GPIO_WS16C48
	tristate "WinSystems WS16C48 GPIO support"
803
	select ISA_BUS_API
804
805
	select GPIOLIB_IRQCHIP
	help
806
807
808
809
	  Enables GPIO support for the WinSystems WS16C48. The base port
	  addresses for the devices may be configured via the base module
	  parameter. The interrupt line numbers for the devices may be
	  configured via the irq module parameter.
810

811
812
endmenu

813
814
menu "I2C GPIO expanders"
	depends on I2C
815

816
817
config GPIO_ADP5588
	tristate "ADP5588 I2C GPIO expander"
818
	help
819
820
	  This option enables support for 18 GPIOs found
	  on Analog Devices ADP5588 GPIO Expanders.
821

822
823
824
config GPIO_ADP5588_IRQ
	bool "Interrupt controller support for ADP5588"
	depends on GPIO_ADP5588=y
825
	select GPIOLIB_IRQCHIP
826
	help
827
828
	  Say yes here to enable the adp5588 to be used as an interrupt
	  controller. It requires the driver to be built in the kernel.
829

830
831
config GPIO_ADNP
	tristate "Avionic Design N-bit GPIO expander"
832
	depends on OF_GPIO
833
834
	select GPIOLIB_IRQCHIP
	help
835
836
837
838
839
840
	  This option enables support for N GPIOs found on Avionic Design
	  I2C GPIO expanders. The register space will be extended by powers
	  of two, so the controller will need to accommodate for that. For
	  example: if a controller provides 48 pins, 6 registers will be
	  enough to represent all pins, but the driver will assume a
	  register layout for 64 pins (8 registers).
841

842
843
844
845
846
847
848
config GPIO_GW_PLD
	tristate "Gateworks PLD GPIO Expander"
	depends on OF_GPIO
	help
	  Say yes here to provide access to the Gateworks I2C PLD GPIO
	  Expander. This is used at least on the Cambria GW2358-4.

849
850
851
852
config GPIO_MAX7300
	tristate "Maxim MAX7300 GPIO expander"
	select GPIO_MAX730X
	help
853
	  GPIO driver for Maxim MAX7300 I2C-based GPIO expander.
854

Eric Miao's avatar
Eric Miao committed
855
856
857
858
859
860
861
862
863
config GPIO_MAX732X
	tristate "MAX7319, MAX7320-7327 I2C Port Expanders"
	help
	  Say yes here to support the MAX7319, MAX7320-7327 series of I2C
	  Port Expanders. Each IO port on these chips has a fixed role of
	  Input (designated by 'I'), Push-Pull Output ('O'), or Open-Drain
	  Input and Output (designed by 'P'). The combinations are listed
	  below:

864
865
	  8 bits:       max7319 (8I), max7320 (8O), max7321 (8P),
	                max7322 (4I4O), max7323 (4P4O)
Eric Miao's avatar
Eric Miao committed
866

867
868
	  16 bits:      max7324 (8I8O), max7325 (8P8O),
	                max7326 (4I12O), max7327 (4P12O)
Eric Miao's avatar
Eric Miao committed
869
870
871
872

	  Board setup code must specify the model to use, and the start
	  number for these GPIOs.

873
874
config GPIO_MAX732X_IRQ
	bool "Interrupt controller support for MAX732x"
875
	depends on GPIO_MAX732X=y
876
	select GPIOLIB_IRQCHIP
877
878
879
880
	help
	  Say yes here to enable the max732x to be used as an interrupt
	  controller. It requires the driver to be built in the kernel.

881
882
config GPIO_MC9S08DZ60
	bool "MX35 3DS BOARD MC9S08DZ60 GPIO functions"
883
	depends on I2C=y && MACH_MX35_3DS
884
885
886
	help
	  Select this to enable the MC9S08DZ60 GPIO driver

887
config GPIO_PCA953X
Aaron Sierra's avatar
Aaron Sierra committed
888
	tristate "PCA95[357]x, PCA9698, TCA64xx, and MAX7310 I/O ports"
889
	select REGMAP_I2C
890
	help
891
892
893
894
	  Say yes here to provide access to several register-oriented
	  SMBus I/O expanders, made mostly by NXP or TI.  Compatible
	  models include:

895
	  4 bits:       pca9536, pca9537
896

897
898
	  8 bits:       max7310, max7315, pca6107, pca9534, pca9538, pca9554,
	                pca9556, pca9557, pca9574, tca6408, tca9554, xra1202
899

900
901
	  16 bits:      max7312, max7313, pca9535, pca9539, pca9555, pca9575,
	                tca6416
902

903
	  24 bits:      tca6424
904

905
	  40 bits:      pca9505, pca9698
906

907
908
909
config GPIO_PCA953X_IRQ
	bool "Interrupt controller support for PCA953x"
	depends on GPIO_PCA953X=y
910
	select GPIOLIB_IRQCHIP
911
912
913
914
	help
	  Say yes here to enable the pca953x to be used as an interrupt
	  controller. It requires the driver to be built in the kernel.

915
config GPIO_PCF857X
916
	tristate "PCF857x, PCA{85,96}7x, and MAX732[89] I2C GPIO expanders"
917
	select GPIOLIB_IRQCHIP
918
	select IRQ_DOMAIN
919
920
921
922
923
924
925
	help
	  Say yes here to provide access to most "quasi-bidirectional" I2C
	  GPIO expanders used for additional digital outputs or inputs.
	  Most of these parts are from NXP, though TI is a second source for
	  some of them.  Compatible models include:

	  8 bits:   pcf8574, pcf8574a, pca8574, pca8574a,
926
	            pca9670, pca9672, pca9674, pca9674a,
927
	            max7328, max7329
928
929
930
931
932
933
934
935
936
937
938
939

	  16 bits:  pcf8575, pcf8575c, pca8575,
	            pca9671, pca9673, pca9675

	  Your board setup code will need to declare the expanders in
	  use, and assign numbers to the GPIOs they expose.  Those GPIOs
	  can then be used from drivers and other kernel code, just like
	  other GPIOs, but only accessible from task contexts.

	  This driver provides an in-kernel interface to those GPIOs using
	  platform-neutral GPIO calls.

940
941
942
943
944
945
946
947
config GPIO_TPIC2810
	tristate "TPIC2810 8-Bit I2C GPO expander"
	help
	  Say yes here to enable the GPO driver for the TI TPIC2810 chip.

	  To compile this driver as a module, choose M here: the module will
	  be called gpio-tpic2810.

948
949
config GPIO_TS4900
	tristate "Technologic Systems FPGA I2C GPIO"
950
	depends on SOC_IMX6 || COMPILE_TEST
951
952
953
954
955
	select REGMAP_I2C
	help
	  Say yes here to enabled the GPIO driver for Technologic's FPGA core.
	  Series supported include TS-4100, TS-4900, TS-7970 and TS-7990.

956
957
958
endmenu

menu "MFD GPIO expanders"
959
960
961
962
963
964
965
966

config GPIO_ADP5520
	tristate "GPIO Support for ADP5520 PMIC"
	depends on PMIC_ADP5520
	help
	  This option enables support for on-chip GPIO found
	  on Analog Devices ADP5520 PMICs.

967
968
969
970
971
972
973
974
config GPIO_ALTERA_A10SR
	tristate "Altera Arria10 System Resource GPIO"
	depends on MFD_ALTERA_A10SR
	help
	  Driver for Arria10 Development Kit GPIO expansion which
	  includes reads of pushbuttons and DIP switches as well
	  as writes to LEDs.

975
976
977
978
979
980
config GPIO_ARIZONA
	tristate "Wolfson Microelectronics Arizona class devices"
	depends on MFD_ARIZONA
	help
	  Support for GPIOs on Wolfson Arizona class devices.

981
982
983
984
985
986
987
988
989
990
991
config GPIO_BD9571MWV
	tristate "ROHM BD9571 GPIO support"
	depends on MFD_BD9571MWV
	help
	  Support for GPIOs on ROHM BD9571 PMIC. There are two GPIOs
	  available on the ROHM PMIC in total, both of which can also
	  generate interrupts.

	  This driver can also be built as a module. If so, the module
	  will be called gpio-bd9571mwv.

992
993
config GPIO_CRYSTAL_COVE
	tristate "GPIO support for Crystal Cove PMIC"
994
	depends on (X86 || COMPILE_TEST) && INTEL_SOC_PMIC
995
996
997
998
999
1000
1001
1002
1003
1004
1005
1006
	select GPIOLIB_IRQCHIP
	help
	  Support for GPIO pins on Crystal Cove PMIC.

	  Say Yes if you have a Intel SoC based tablet with Crystal Cove PMIC
	  inside.

	  This driver can also be built as a module. If so, the module will be
	  called gpio-crystalcove.

config GPIO_CS5535
	tristate "AMD CS5535/CS5536 GPIO support"
1007
	depends on X86 || MIPS || COMPILE_TEST
1008
1009
1010
1011
1012
1013
1014
1015
1016
1017
1018
1019
1020
1021
1022
1023
1024
1025
1026
1027
1028
1029
1030
1031
1032
1033
1034
1035
1036
1037
1038
1039
1040
1041
1042
1043
1044
	depends on MFD_CS5535
	help
	  The AMD CS5535 and CS5536 southbridges support 28 GPIO pins that
	  can be used for quite a number of things.  The CS5535/6 is found on
	  AMD Geode and Lemote Yeeloong devices.

	  If unsure, say N.

config GPIO_DA9052
	tristate "Dialog DA9052 GPIO"
	depends on PMIC_DA9052
	help
	  Say yes here to enable the GPIO driver for the DA9052 chip.

config GPIO_DA9055
	tristate "Dialog Semiconductor DA9055 GPIO"
	depends on MFD_DA9055
	help
	  Say yes here to enable the GPIO driver for the DA9055 chip.

	  The Dialog DA9055 PMIC chip has 3 GPIO pins that can be
	  be controller by this driver.

	  If driver is built as a module it will be called gpio-da9055.

config GPIO_DLN2
	tristate "Diolan DLN2 GPIO support"
	depends on MFD_DLN2
	select GPIOLIB_IRQCHIP

	help
	  Select this option to enable GPIO driver for the Diolan DLN2
	  board.

	  This driver can also be built as a module. If so, the module
	  will be called gpio-dln2.

1045
1046
1047
1048
config HTC_EGPIO
	bool "HTC EGPIO support"
	depends on GPIOLIB && ARM
	help
1049
1050
1051
	  This driver supports the CPLD egpio chip present on
	  several HTC phones.  It provides basic support for input
	  pins, output pins, and irqs.
1052

1053
1054
1055
1056
1057
1058
1059
1060
1061
1062
1063
1064
1065
1066
1067
1068
1069
1070
1071
1072
1073
1074
1075
1076
1077
1078
config GPIO_JANZ_TTL
	tristate "Janz VMOD-TTL Digital IO Module"
	depends on MFD_JANZ_CMODIO
	help
	  This enables support for the Janz VMOD-TTL Digital IO module.
	  This driver provides support for driving the pins in output
	  mode only. Input mode is not supported.

config GPIO_KEMPLD
	tristate "Kontron ETX / COMexpress GPIO"
	depends on MFD_KEMPLD
	help
	  This enables support for the PLD GPIO interface on some Kontron ETX
	  and COMexpress (ETXexpress) modules.

	  This driver can also be built as a module. If so, the module will be
	  called gpio-kempld.

config GPIO_LP3943
	tristate "TI/National Semiconductor LP3943 GPIO expander"
	depends on MFD_LP3943
	help
	  GPIO driver for LP3943 MFD.
	  LP3943 can be used as a GPIO expander which provides up to 16 GPIOs.
	  Open drain outputs are required for this usage.

1079
1080
1081
1082
1083
1084
1085
1086
config GPIO_LP873X
	tristate "TI LP873X GPO"
	depends on MFD_TI_LP873X
	help
	  This driver supports the GPO on TI Lp873x PMICs. 2 GPOs are present
	  on LP873X PMICs.

	  This driver can also be built as a module. If so, the module will be
1087
	  called gpio-lp873x.
1088

Keerthy's avatar
Keerthy committed
1089
1090
1091
1092
1093
1094
1095
1096
1097
1098
config GPIO_LP87565
	tristate "TI LP87565 GPIO"
	depends on MFD_TI_LP87565
	help
	  This driver supports the GPIO on TI Lp873565 PMICs. 3 GPIOs are present
	  on LP87565 PMICs.

	  This driver can also be built as a module. If so, the module will be
	  called gpio-lp87565.

1099
1100
1101
1102
1103
1104
config GPIO_MADERA
	tristate "Cirrus Logic Madera class codecs"
	depends on PINCTRL_MADERA
	help
	  Support for GPIOs on Cirrus Logic Madera class codecs.

1105
1106
1107
1108
1109
1110
1111
1112
1113
config GPIO_MAX77620
	tristate "GPIO support for PMIC MAX77620 and MAX20024"
	depends on MFD_MAX77620
	help
	  GPIO driver for MAX77620 and MAX20024 PMIC from Maxim Semiconductor.
	  MAX77620 PMIC has 8 pins that can be configured as GPIOs. The
	  driver also provides interrupt support for each of the gpios.
	  Say yes here to enable the max77620 to be used as gpio controller.

1114
1115
1116
1117
1118
1119
1120
config GPIO_MAX77650
	tristate "Maxim MAX77650/77651 GPIO support"
	depends on MFD_MAX77650
	help
	  GPIO driver for MAX77650/77651 PMIC from Maxim Semiconductor.
	  These chips have a single pin that can be configured as GPIO.

1121
1122
config GPIO_MSIC
	bool "Intel MSIC mixed signal gpio support"
1123
	depends on (X86 || COMPILE_TEST) && MFD_INTEL_MSIC
1124
1125
1126
1127
1128
1129
1130
1131
1132
1133
1134
	help
	  Enable support for GPIO on intel MSIC controllers found in
	  intel MID devices

config GPIO_PALMAS
	bool "TI PALMAS series PMICs GPIO"
	depends on MFD_PALMAS
	help
	  Select this option to enable GPIO driver for the TI PALMAS
	  series chip family.

1135
1136
1137
1138
1139
1140
1141
1142
1143
config GPIO_RC5T583
	bool "RICOH RC5T583 GPIO"
	depends on MFD_RC5T583
	help
	  Select this option to enable GPIO driver for the Ricoh RC5T583
	  chip family.
	  This driver provides the support for driving/reading the gpio pins
	  of RC5T583 device through standard gpio library.

Rabin Vincent's avatar
Rabin Vincent committed
1144
1145
1146
config GPIO_STMPE
	bool "STMPE GPIOs"
	depends on MFD_STMPE
1147
	depends on OF_GPIO
1148
	select GPIOLIB_IRQCHIP
Rabin Vincent's avatar
Rabin Vincent committed
1149
1150
1151
1152
	help
	  This enables support for the GPIOs found on the STMPE I/O
	  Expanders.

1153
1154
1155
config GPIO_TC3589X
	bool "TC3589X GPIOs"
	depends on MFD_TC3589X
1156
	depends on OF_GPIO
1157
	select GPIOLIB_IRQCHIP
Rabin Vincent's avatar
Rabin Vincent committed
1158
	help
1159
	  This enables support for the GPIOs found on the TC3589X
Rabin Vincent's avatar
Rabin Vincent committed
1160
1161
	  I/O Expander.

1162
1163
1164
1165
1166
1167
config GPIO_TIMBERDALE
	bool "Support for timberdale GPIO IP"
	depends on MFD_TIMBERDALE
	---help---
	Add support for the GPIO IP in the timberdale FPGA.

1168
1169
1170
1171
1172
1173
config GPIO_TPS65086
	tristate "TI TPS65086 GPO"
	depends on MFD_TPS65086
	help
	  This driver supports the GPO on TI TPS65086x PMICs.

1174
1175
1176
1177
1178
1179
1180
config GPIO_TPS65218
	tristate "TPS65218 GPIO"
	depends on MFD_TPS65218
	help
	  Select this option to enable GPIO driver for the TPS65218
	  chip family.

1181
1182
1183
1184
1185
1186
1187
1188
1189
1190
1191
1192
1193
1194
config GPIO_TPS6586X
	bool "TPS6586X GPIO"
	depends on MFD_TPS6586X
	help
	  Select this option to enable GPIO driver for the TPS6586X
	  chip family.

config GPIO_TPS65910
	bool "TPS65910 GPIO"
	depends on MFD_TPS65910
	help
	  Select this option to enable GPIO driver for the TPS65910
	  chip family.

1195
1196
config GPIO_TPS65912
	tristate "TI TPS65912 GPIO"
1197
	depends on MFD_TPS65912
1198
1199
1200
	help
	  This driver supports TPS65912 gpio chip

1201
1202
1203
1204
1205
1206
1207
1208
1209
1210
1211
1212
1213
1214
1215
config GPIO_TPS68470
	bool "TPS68470 GPIO"
	depends on MFD_TPS68470
	help
	  Select this option to enable GPIO driver for the TPS68470
	  chip family.
	  There are 7 GPIOs and few sensor related GPIOs supported
	  by the TPS68470. While the 7 GPIOs can be configured as
	  input or output as appropriate, the sensor related GPIOs
	  are "output only" GPIOs.

	  This driver config is bool, as the GPIO functionality
	  of the TPS68470 must be available before dependent
	  drivers are loaded.

1216
1217
1218
1219
1220
1221
1222
config GPIO_TQMX86
	tristate "TQ-Systems QTMX86 GPIO"
	depends on MFD_TQMX86 || COMPILE_TEST
	select GPIOLIB_IRQCHIP
	help
	  This driver supports GPIO on the TQMX86 IO controller.

David Brownell's avatar
David Brownell committed
1223
1224
1225
1226
1227
1228
1229
config GPIO_TWL4030
	tristate "TWL4030, TWL5030, and TPS659x0 GPIOs"
	depends on TWL4030_CORE
	help
	  Say yes here to access the GPIO signals of various multi-function
	  power management chips from Texas Instruments.

1230
1231
1232
1233
1234
1235
1236
config GPIO_TWL6040
	tristate "TWL6040 GPO"
	depends on TWL6040_CORE
	help
	  Say yes here to access the GPO signals of twl6040
	  audio chip from Texas Instruments.

1237
1238
1239
1240
1241
1242
1243
config GPIO_UCB1400
	tristate "Philips UCB1400 GPIO"
	depends on UCB1400_CORE
	help
	  This enables support for the Philips UCB1400 GPIO pins.
	  The UCB1400 is an AC97 audio codec.

1244
1245
config GPIO_WHISKEY_COVE
	tristate "GPIO support for Whiskey Cove PMIC"
1246
	depends on (X86 || COMPILE_TEST) && INTEL_SOC_PMIC_BXTWC
1247
1248
1249
1250
1251
1252
1253
1254
1255
1256
	select GPIOLIB_IRQCHIP
	help
	  Support for GPIO pins on Whiskey Cove PMIC.

	  Say Yes if you have a Intel SoC based tablet with Whiskey Cove PMIC
	  inside.

	  This driver can also be built as a module. If so, the module will be
	  called gpio-wcove.

Mark Brown's avatar
Mark Brown committed
1257
1258
1259
1260
1261
1262
1263
config GPIO_WM831X
	tristate "WM831x GPIOs"
	depends on MFD_WM831X
	help
	  Say yes here to access the GPIO signals of WM831x power management
	  chips from Wolfson Microelectronics.

1264
1265
1266
1267
1268
1269
1270
config GPIO_WM8350
	tristate "WM8350 GPIOs"
	depends on MFD_WM8350
	help
	  Say yes here to access the GPIO signals of WM8350 power management
	  chips from Wolfson Microelectronics.

Mark Brown's avatar
Mark Brown committed
1271
1272
1273
1274
1275
1276
1277
config GPIO_WM8994
	tristate "WM8994 GPIOs"
	depends on MFD_WM8994
	help
	  Say yes here to access the GPIO signals of WM8994 audio hub
	  CODECs from Wolfson Microelectronics.

1278
endmenu
1279

1280
1281
menu "PCI GPIO expanders"
	depends on PCI
1282

1283
1284
config GPIO_AMD8111
	tristate "AMD 8111 GPIO driver"
1285
	depends on X86 || COMPILE_TEST
1286
	help
1287
	  The AMD 8111 south bridge contains 32 GPIO pins which can be used.
Michael Buesch's avatar
Michael Buesch committed
1288

1289
1290
1291
	  Note, that usually system firmware/ACPI handles GPIO pins on their
	  own and users might easily break their systems with uncarefull usage
	  of this driver!
1292

1293
	  If unsure, say N
1294

Michael Buesch's avatar
Michael Buesch committed
1295
1296
config GPIO_BT8XX
	tristate "BT8XX GPIO abuser"
1297
	depends on VIDEO_BT848=n
Michael Buesch's avatar
Michael Buesch committed
1298
	help
1299
	  The BT8xx frame grabber chip has 24 GPIO pins that can be abused
Michael Buesch's avatar
Michael Buesch committed
1300
1301
1302
1303
1304
1305
1306
1307
1308
1309
1310
	  as a cheap PCI GPIO card.

	  This chip can be found on Miro, Hauppauge and STB TV-cards.

	  The card needs to be physically altered for using it as a
	  GPIO card. For more information on how to build a GPIO card
	  from a BT8xx TV card, see the documentation file at
	  Documentation/bt8xxgpio.txt

	  If unsure, say N.

1311
config GPIO_INTEL_MID
1312
1313
	bool "Intel MID GPIO support"
	depends on X86_INTEL_MID
1314
	select GPIOLIB_IRQCHIP
1315
	help
1316
	  Say Y here to support Intel MID GPIO.
1317

1318
1319
1320
config GPIO_MERRIFIELD
	tristate "Intel Merrifield GPIO support"
	depends on X86_INTEL_MID
1321
	select GPIOLIB_IRQCHIP
1322
	help
1323
	  Say Y here to support Intel Merrifield GPIO.
1324

1325
1326
config GPIO_MLXBF
	tristate "Mellanox BlueField SoC GPIO"
1327
	depends on (MELLANOX_PLATFORM && ARM64 && ACPI) || (64BIT && COMPILE_TEST)
1328
1329
1330
1331
	select GPIO_GENERIC
	help
	  Say Y here if you want GPIO support on Mellanox BlueField SoC.

1332
1333
config GPIO_ML_IOH
	tristate "OKI SEMICONDUCTOR ML7213 IOH GPIO support"
1334
	depends on X86 || COMPILE_TEST
1335
1336
1337
1338
1339
1340
1341
	select GENERIC_IRQ_CHIP
	help
	  ML7213 is companion chip for Intel Atom E6xx series.
	  This driver can be used for OKI SEMICONDUCTOR ML7213 IOH(Input/Output
	  Hub) which is for IVI(In-Vehicle Infotainment) use.
	  This driver can access the IOH's GPIO device.

1342
config GPIO_PCH
1343
	tristate "Intel EG20T PCH/LAPIS Semiconductor IOH(ML7223/ML7831) GPIO"
1344
	depends on X86_32 || MIPS || COMPILE_TEST
1345
	select GENERIC_IRQ_CHIP
1346
1347
1348
1349
1350
	help
	  This driver is for PCH(Platform controller Hub) GPIO of Intel Topcliff
	  which is an IOH(Input/Output Hub) for x86 embedded processor.
	  This driver can access PCH GPIO device.

1351
1352
	  This driver also can be used for LAPIS Semiconductor IOH(Input/
	  Output Hub), ML7223 and ML7831.
1353
	  ML7223 IOH is for MP(Media Phone) use.
1354
1355
1356
	  ML7831 IOH is for general purpose use.
	  ML7223/ML7831 is companion chip for Intel Atom E6xx series.
	  ML7223/ML7831 is completely compatible for Intel EG20T PCH.
1357

1358
1359
1360
1361
1362
1363
1364
1365
1366
config GPIO_PCI_IDIO_16
	tristate "ACCES PCI-IDIO-16 GPIO support"
	select GPIOLIB_IRQCHIP
	help
	  Enables GPIO support for the ACCES PCI-IDIO-16. An interrupt is
	  generated when any of the inputs change state (low to high or high to
	  low). Input filter control is not supported by this driver, and the
	  input filters are deactivated by this driver.

1367
1368
1369
1370
1371
1372
1373
1374
1375
1376
config GPIO_PCIE_IDIO_24
	tristate "ACCES PCIe-IDIO-24 GPIO support"
	select GPIOLIB_IRQCHIP
	help
	  Enables GPIO support for the ACCES PCIe-IDIO-24 family (PCIe-IDIO-24,
	  PCIe-IDI-24, PCIe-IDO-24, PCIe-IDIO-12). An interrupt is generated
	  when any of the inputs change state (low to high or high to low).
	  Input filter control is not supported by this driver, and the input
	  filters are deactivated by this driver.

1377
1378
1379
1380
config GPIO_RDC321X
	tristate "RDC R-321x GPIO support"
	select MFD_CORE
	select MFD_RDC321X
1381
	help
1382
1383
	  Support for the RDC R321x SoC GPIOs over southbridge
	  PCI configuration space.
1384

1385
1386
config GPIO_SODAVILLE
	bool "Intel Sodaville GPIO support"
1387
	depends on X86 && OF
1388
1389
1390
1391
1392
	select GPIO_GENERIC
	select GENERIC_IRQ_CHIP
	help
	  Say Y here to support Intel Sodaville GPIO.

1393
endmenu
1394

1395
1396
menu "SPI GPIO expanders"
	depends on SPI_MASTER
1397

1398
1399
config GPIO_74X164
	tristate "74x164 serial-in/parallel-out 8-bits shift register"
1400
	depends on OF_GPIO
1401
1402
1403
1404
	help
	  Driver for 74x164 compatible serial-in/parallel-out 8-outputs
	  shift registers. This driver can be used to provide access
	  to more gpio outputs.
1405

1406
1407
1408
1409
1410
1411
1412
1413
1414
1415
config GPIO_MAX3191X
	tristate "Maxim MAX3191x industrial serializer"
	select CRC8
	help
	  GPIO driver for Maxim MAX31910, MAX31911, MAX31912, MAX31913,
	  MAX31953 and MAX31963 industrial serializer, a daisy-chainable
	  chip to make 8 digital 24V inputs available via SPI.  Supports
	  CRC checksums to guard against electromagnetic interference,
	  as well as undervoltage and overtemperature detection.

1416
1417
config GPIO_MAX7301
	tristate "Maxim MAX7301 GPIO expander"
1418
	select GPIO_MAX730X
1419
	help
1420
	  GPIO driver for Maxim MAX7301 SPI-based GPIO expander.
1421

Richard Röjfors's avatar
Richard Röjfors committed
1422
1423
1424
1425
1426
1427
config GPIO_MC33880
	tristate "Freescale MC33880 high-side/low-side switch"
	help
	  SPI driver for Freescale MC33880 high-side/low-side switch.
	  This provides GPIO interface supporting inputs and outputs.