GitLab

This adds support for PCI-X and PCIe on the p5ioc2 IO hub using
OPAL. This includes allocating & setting up TCE tables and config
space access routines.

This also supports fallbacks via RTAS when OPAL is absent, using
legacy TCE format pre-allocated via the device-tree (BML style)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

OPAL can handle various interrupt for us such as Machine Checks (it
performs all sorts of recovery tasks and passes back control to us with
informations about the error), Hardware Management Interrupts and Softpatch
interrupts.

This wires up the mechanisms and prints out specific informations returned
by HAL when a machine check occurs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

We do the minimum which is to "pass" interrupts to HAL, which
makes the console smoother and will allow us to implement
interrupt based completion and console.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Implements OPAL RTC and NVRAM support and wire all that up to
the powernv platform.

We use RTAS for RTC as a fallback if available. Using RTAS for nvram
is not supported yet, pending some rework/cleanup and generalization
of the pSeries & CHRP code. We also use RTAS fallbacks for power off
and reboot
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This calls the respective HAL functions, and spin on hal_poll_event()
to ensure the HAL has a chance to communicate with the FSP to trigger
the reboot or shutdown operation
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This adds a udbg and an hvc console backend for supporting a console
using the OPAL console interfaces.

On OPAL v1 we have hvc0 mapped to whatever console the system was
configured for (network or hvsi serial port) via the service
processor.

On OPAL v2 we have hvcN mapped to the Nth console provided by OPAL
which generally corresponds to:

	hvc0 : network console (raw protocol)
	hvc1 : serial port S1 (hvsi)
	hvc2 : serial port S2 (hvsi)

Note: At this point, early debug console only works with OPAL v1
and shouldn't be enabled in a normal kernel.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Add definition of OPAL interfaces along with  the wrappers to call
into OPAL runtime and the early device-tree parsing hook to locate
the OPAL runtime firmware.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

On machines supporting the OPAL firmware version 1, the system
is initially booted under pHyp. We then use a special hypercall
to verify if OPAL is available and if it is, we then trigger
a "takeover" which disables pHyp and loads the OPAL runtime
firmware, giving control to the kernel in hypervisor mode.

This patch add the necessary code to detect that the OPAL takeover
capability is present when running under PowerVM (aka pHyp) and
perform said takeover to get hypervisor control of the processor.

To perform the takeover, we must first use RTAS (within Open
Firmware runtime environment) to start all processors & threads,
in order to give control to OPAL on all of them. We then call
the takeover hypercall on everybody, OPAL will re-enter the kernel
main entry point passing it a flat device-tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Unplugged CPU go into NAP mode in a loop until woken up
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This adds a skeletton for the new Power "Non Virtualized"
platform which will be used by machines supporting running
without an hypervisor, for example in order to run KVM.

These machines will be using a new firmware called OPAL
for which the support will be provided by later patches.

The PowerNV platform is intended to be also usable under
the BML environment used internally for early CPU bringup
which is why the code also supports using RTAS instead of
OPAL in various places.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Add a new udbg driver for the PS3 gelic Ehthernet device.

This driver shares only a few stucture and constant definitions with the
gelic Ethernet device driver, so is implemented as a stand-alone driver
with no dependencies on the gelic Ethernet device driver.
Signed-off-by: Hector Martin <hector@marcansoft.com>
Signed-off-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Since commit 188917e1

, /proc/ppc64 is a
symlink to /proc/powerpc/. That means that creating /proc/ppc64/eeh will
end up with a unaccessible file, that is not listed under /proc/powerpc/
and, then, not listed under /proc/ppc64/.

Creating /proc/powerpc/eeh fixes that problem and maintain the
compatibility intended with the ppc64 symlink.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: <stable@kernel.org>	[3.x]

During hotplug CPU add we get the following error:

Unexpected Error (0) returned from configure-connector

ibm,configure-connector returns 0 for configuration complete, so
catch this and avoid the error.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: <stable@kernel.org>

Based on a patch by Michael Ellerman <michael@ellerman.id.au>

Patch was simply forward ported upstream.

Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Based on a patch by Benjamin Herrenschmidt <benh@kernel.crashing.org>

Modernized and slightly modified to not record erros into the nvram
log since we do not have that device driver just yet.

Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Some config selections were applied to the platform (reference board)
when they actuall apply to the chip.
Signed-off-by: Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

At this point, window has not been stored anywhere, so it has to be freed
before leaving the function.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/

)

// <smpl>
@exists@
local idexpression x;
statement S,S1;
expression E;
identifier fl;
expression *ptr != NULL;
@@

x = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
     when != if (...) { <+...kfree(x)...+> }
     when any
     when != true x == NULL
x->fl
...>
(
if (x == NULL) S1
|
if (...) { ... when != x
               when forall
(
 return \(0\|<+...x...+>\|ptr\);
|
* return ...;
)
}
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Capture more than twice as much text from the printk buffer, and
compress it to fit it in the lnx,oops-log NVRAM partition.  You
can view the compressed text using the new (as of July 20) --unzip
option of the nvram command in the powerpc-utils package.

[BenH: Added select of ZLIB_DEFLATE]
Signed-off-by: Jim Keniston <jkenisto@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Enable hugepages on Freescale BookE processors.  This allows the kernel to
use huge TLB entries to map pages, which can greatly reduce the number of
TLB misses and the amount of TLB thrashing experienced by applications with
large memory footprints.  Care should be taken when using this on FSL
processors, as the number of large TLB entries supported by the core is low
(16-64) on current processors.

The supported set of hugepage sizes include 4m, 16m, 64m, 256m, and 1g.
Page sizes larger than the max zone size are called "gigantic" pages and
must be allocated on the command line (and cannot be deallocated).

This is currently only fully implemented for Freescale 32-bit BookE
processors, but there is some infrastructure in the code for
64-bit BooKE.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Now that the generic code has dma_map_ops set, instead of having a
messy ifdef & if block in the base dma_get_required_mask hook push
the computation into the dma ops.

If the ops fails to set the get_required_mask hook default to the
width of dma_addr_t.

This also corrects ibmbus ibmebus_dma_supported to require a 64
bit mask.  I doubt anything is checking or setting the dma mask on
that bus.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Cc: benh@kernel.crashing.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The hook dma_get_required_mask is supposed to return the mask required
by the platform to operate efficently.  The generic version of
dma_get_required_mask in driver/base/platform.c returns a mask based
only on max_pfn.  However, this is likely too big for iommu systems
and could be too small for platforms that require a dma offset or have
a secondary window at a high offset.

Override the default, provide a hook in ppc_md used by pseries lpar and
cell, and provide the default answer based on memblock_end_of_DRAM(),
with hooks for get_dma_offset, and provide an implementation for iommu
that looks at the defined table size.  Coverting from the end address
to the required bit mask is based on the generic implementation.

The need for this was discovered when the qla2xxx driver switched to
64 bit dma then reverted to 32 bit when dma_get_required_mask said
32 bits was sufficient.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Cc: benh@kernel.crashing.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The HCU4 board is unmaintained.  Remove it.
Signed-off-by: Niklaus Giger <niklaus.giger@member.fsf.org>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>

The VPA, SLB shadow and DTL degistration functions do not need an
address, so simplify things and remove it.

Also cleanup pseries_kexec_cpu_down a bit by storing the cpu IDs
in local variables.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Make the VPA, SLB shadow and DTL registration and deregistration
functions print consistent messages on error. I needed the firmware
error code while chasing a kexec bug but we weren't printing it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Recent versions of firmware will fail to unmap the virtual processor
area if we have a dispatch trace log registered. This causes kexec
to fail.

If a trace log is registered this patch unregisters it before the
SLB shadow and virtual processor areas, fixing the problem.

The address argument is ignored by firmware on unregister so we
may as well remove it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

KVM_GUEST adds a 1 MB array to the kernel (kvm_tmp) which grew
my kernel enough to cause it to fail to boot.

Dynamically allocating or reducing the size of this array is a
good idea, but in the meantime I think it makes sense to make
KVM_GUEST default to n in order to minimise surprises.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The ibm,io-events code is a bit verbose with its error messages.
Reverse the reporting so we only print when we successfully enable
I/O event interrupts.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

On a box with 8TB of RAM the MMU hashtable is 64GB in size. That
means we have 4G PTEs. pSeries_lpar_hptab_clear was using a signed
int to store the index which will overflow at 2G.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Change the string to check for CAMP mode boot on MPC85xx (eg. P2020) to match
the one in the corresponding dts files (p2020rdb_camp_core{0,1}.dts).

Without this fix the mpic is configured as in the SMP boot mode, which causes
the first core to report a protected source interrupt error for devices
of the other core and lock up.

Also add MPIC_SINGLE_DEST_CPU on both P2020 based architectures in CAMP
mode as suggested by Scott Wood. Thanks.

Cc: Scott Wood <scottwood@freescale.com>
Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

The 64-bit Book-E parts (to date) dont utilize the 'server' class
perfmon.  So building or depending on it makes no sense (and does break
FSL Book-E 64-bit support).  Move the selection of PPC_HAVE_PMU_SUPPORT
to be based on PPC_BOOK3S_64.

Based on a patch from Scott Wood.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Btrfs needs to be able to control how filemap_write_and_wait_range() is called
in fsync to make it less of a painful operation, so push down taking i_mutex and
the calling of filemap_write_and_wait() down into the ->fsync() handlers.  Some
file systems can drop taking the i_mutex altogether it seems, like ext3 and
ocfs2.  For correctness sake I just pushed everything down in all cases to make
sure that we keep the current behavior the same for everybody, and then each
individual fs maintainer can make up their mind about what to do from there.
Thanks,
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Return -EAGAIN when we get H_BUSY back from the hypervisor. This
makes the hvc console driver retry, avoiding dropped printks.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This renames pci flags functions and enums in preparation for creating
generic version in asm-generic/pci-bridge.h. The following search and
replace is done:

s/ppc_pci_/pci_/
s/PPC_PCI_/PCI_/

Direct accesses to ppc_pci_flag variable are replaced with helper
functions.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>

Instead of branching out-of-line with the DO_KVM macro to check if we
are in a KVM guest at the time of an interrupt, this moves the KVM
check inline in the first-level interrupt handlers.  This speeds up
the non-KVM case and makes sure that none of the interrupt handlers
are missing the check.

Because the first-level interrupt handlers are now larger, some things
had to be move out of line in exceptions-64s.S.

This all necessitated some minor changes to the interrupt entry code
in KVM.  This also streamlines the book3s_32 KVM test.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>

Just compiling pseries in the kernel causes it to override
memory_block_size_bytes() regardless of what is the runtime
platform.

This cleans up the implementation of that function, fixing
a bug or two while at it, so that it's harmless (and potentially
useful) for other platforms. Without this, bugs in that code
would trigger a WARN_ON() in drivers/base/memory.c when
booting some different platforms.

If/when we have another platform supporting memory hotplug we
might want to either move that out to a generic place or
make it a ppc_md. callback.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Under the FSL Hypervisor we triggered a BUG_ON in mpc85xx_smp_init that
expected smp_ops.message_pass to be explicity set.  However recent
changes allows smp_ops.message_pass to be NULL and handled by default
code.  Thus the BUG_ON isn't relevant anymore.
Signed-off-by: Laurentiu TUDOR <Laurentiu.Tudor@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

P2040RDB Specification:
-----------------------
2Gbyte unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
128 Mbyte NOR flash single-chip memory
256 Kbit M24256 I2C EEPROM
16 Mbyte SPI memory
SD connector to interface with the SD memory card
dTSEC1: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC2: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC3: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC4: connected to the Vitesse RGMII PHY (VSC8641)
dTSEC5: connected to the Vitesse RGMII PHY (VSC8641)
I2C1: Real time clock, Temperature sensor
I2C2: Vcore Regulator, 256Kbit I2C Bus EEPROM
SATA: Lanes C and Land D of Bank2 are connected to two SATA connectors
UART: supports two UARTs up to 115200 bps for console
USB 2.0: connected via a internal UTMI PHY to two TYPE-A interfaces
PCIe:
 - Lanes E, F, G and H of Bank1 are connected to one x4 PCIe SLOT1
 - Lanes C and Land D of Bank2 are connected to one x4 PCIe SLOT2
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

GPIO drivers are getting consolidated into drivers/gpio.  While at it,
change the driver name to mpc5200-gpio* to avoid collisions.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>