- 01 Jul, 2006 11 commits
-
-
Bryan O'Sullivan authored
The tail register read became redundant as the result of earlier receive interrupt bug fixes. Drop another unneeded register read. And another line that got duplicated. Signed-off-by:
Dave Olson <dave.olson@qlogic.com> Signed-off-by:
Bryan O'Sullivan <bryan.osullivan@qlogic.com> Cc: "Michael S. Tsirkin" <mst@mellanox.co.il> Cc: Roland Dreier <rolandd@cisco.com> Signed-off-by:
Andrew Morton <akpm@osdl.org> Signed-off-by:
Linus Torvalds <torvalds@osdl.org>
-
Bryan O'Sullivan authored
Do an extra check to see if in-memory tail changed while processing packets, and if so, going back through the loop again (but only once per call to ipath_kreceive()). In practice, this seems to be enough to guarantee that if we crossed the clearing of an interrupt at start of ipath_intr with a scheduled tail register update, that we'll process the "extra" packet that lost the interrupt because we cleared it just as it was about to arrive. Signed-off-by:
-
Bryan O'Sullivan authored
The problem was that I was updating the head register multiple times in the rcvhdrq processing loop, and setting the counter on each update. Since that meant that the tail register was ahead of head for all but the last update, we would get extra interrupts. The fix was to not write the counter value except on the last update. I also changed to update rcvhdrhead and rcvegrindexhead at most every 16 packets, if there were lots of packets in the queue (and of course, on the last packet, regardless). I also made some small cleanups while debugging this. With these changes, xeon/monty typically sees two openib packets per interrupt on sdp and ipoib, opteron/monty is about 1.25 pkts/intr. I'm seeing about 3800 Mbit/s monty/xeon, and 5000-5100 opteron/monty with netperf sdp. Netpipe doesn't show as good as that, peaking at about 4400 on opteron/monty sdp. Plain ipoib xeon is about 2100+ netperf, opteron 2900+, at 128KB Signed-off-by: olson@eng-12.pathscale.com Signed-off-by:
Bryan O'Sullivan <bos@pathscale.com> Cc: "Michael S. Tsirkin" <mst@mellanox.co.il> Cc: Roland Dreier <rolandd@cisco.com> Signed-off-by:
-
Bryan O'Sullivan authored
Also count the number of interrupts where that works (fastrcvint). On any interrupt where the port0 head and tail registers are not equal, just call the ipath_kreceive code without reading the interrupt status, thus saving the approximately 0.25usec processor stall waiting for the read to return. If any other interrupt bits are set, or head==tail, take the normal path, but that has been reordered to handle read ahead of pioavail. Also no longer call ipath_kreceive() from ipath_qcheck(), because that just seems to make things worse, and isn't really buying us anything, these days. Also no longer loop in ipath_kreceive(); better to not hold things off too long (I saw many cases where we would loop 4-8 times, and handle thousands (up to 3500) in a single call). Signed-off-by:
-
Bryan O'Sullivan authored
Made in-memory rcvhdrq tail update be in dma_alloc'ed memory, not random user or special kernel (needed for ppc, also "just the right thing to do"). Some cleanups to make unexpected link transitions less likely to produce complaints about packet errors, and also to not leave SMA packets stuck and unable to go out. A few other random debug and comment cleanups. Always init rcvhdrq head/tail registers to 0, to avoid race conditions (should have been that way some time ago). Signed-off-by:
-
Bryan O'Sullivan authored
This is not a DMA target, so no need to use dma_alloc_coherent on it. Signed-off-by:
-
Bryan O'Sullivan authored
Signed-off-by:
-
Bryan O'Sullivan authored
Signed-off-by:
-
Bryan O'Sullivan authored
Signed-off-by:
-
Bryan O'Sullivan authored
There is no longer a /dev/ipath_diag file; instead, there's /dev/ipath_diag0, 1, etc. It's still not possible to have diags run on more than one unit at a time, but that's easy to fix at some point. Signed-off-by:
-
Bryan O'Sullivan authored
Signed-off-by:
-
- 27 Jun, 2006 1 commit
-
-
Greg Kroah-Hartman authored
This is needed if we wish to change the size of the resource structures. Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com> Cc: Vivek Goyal <vgoyal@in.ibm.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
- 23 May, 2006 1 commit
-
-
Bryan O'Sullivan authored
Fix NULL deref due to pcidev being clobbered before dd->ipath_f_cleanup() was called. Signed-off-by:
Roland Dreier <rolandd@cisco.com>
-
- 12 May, 2006 1 commit
-
-
Roland Dreier authored
The ipath driver's table of PCI IDs needs a { 0, } entry at the end. This makes all of the device aliases visible to userspace so hotplug loads the module for all supported devices. Without the patch, modinfo ipath_core only shows: alias: pci:v00001FC1d0000000Dsv*sd*bc*sc*i* instead of the correct: alias: pci:v00001FC1d00000010sv*sd*bc*sc*i* alias: pci:v00001FC1d0000000Dsv*sd*bc*sc*i* Signed-off-by:
-
- 01 May, 2006 2 commits
-
-
Bryan O'Sullivan authored
Signed-off-by:
-
Bryan O'Sullivan authored
Some systems do not set up 64-bit maps on systems with 2GB or less of memory installed, so we have to fall back to trying a 32-bit setup. Signed-off-by:
-
- 19 Apr, 2006 1 commit
-
-
Roland Dreier authored
Make symbols that are only used in a single source file static. Signed-off-by:
-
- 31 Mar, 2006 1 commit
-
-
Bryan O'Sullivan authored
The ipath driver is a low-level driver for PathScale InfiniPath host channel adapters (HCAs) based on the HT-400 and PE-800 chips, including the InfiniPath HT-460, the small form factor InfiniPath HT-460, the InfiniPath HT-470 and the Linux Networx LS/X. The ipath_driver.c file contains much of the low-level device handling code. Signed-off-by:
-
