When we don't know the node a PCI bus is connected to return -1.
This matches the generic code.

Noticed by Ravikiran G Thirumalai <kiran@scalex86.org>

Cc: Ravikiran G Thirumalai <kiran@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

A lot of Opteron BIOS just pass 10 in all SLIT entries (10 is the
normalized unit). This is actually worse than the default heuristic
because it leads to pci_distance not knowing the difference between
local and remote nodes anymore. This messes up some NUMA
heuristics in generic code.

In this case it's better to fall back to the default heuristic
which just does nodea == nodeb ? 10 : 20.

This patch does some basic sanity checking on the SLIT and only accepts
the SLIT when it passes.

Invariants enforced are:
- Node to itself shall be 10
- Any other distance shouldn't be 10
- Distances smaller than 10 are illegal
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

The current x86_64 NUMA memory code is inconsequent when it comes to node
memory ranges. The exact behaviour varies depending on which config option
that is used.

setup_node_bootmem() has start and end as arguments and these are used to
calculate the size of the node like this: (end - start). This is all fine
if end is pointing to the first non-available byte. The problem is that the
current x86_64 code sometimes treats it as the last present byte and sometimes
as the first non-available byte. The result is that some configurations might
lose a page at the end of the range.

This patch tries to fix CONFIG_ACPI_NUMA, CONFIG_K8_NUMA and CONFIG_NUMA_EMU
so they all treat the end variable as the first non-available byte. This is
the same way as the single node code.

The patch is boot tested on dual x86_64 hardware with the above configurations,
but maybe the removed code is needed as some workaround?
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Not go from the CPU number to an mapping array.
Mode number is often used now in fast paths.

This also adds a generic numa_node_id to all the topology includes

Suggested by Eric Dumazet
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

The nodes are not set online yet at this point.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Also use for_each_node_mask instead of hand crafted loops.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

- Report PXMs instead of nodes
- Report the correct PXM, not always the one of node 1.
- Only warn for the case of a PXM overlapping by itself
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Since this is shared code I had to implement it for i386 too
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Do that later when the CPU boots. SRAT just stores the APIC<->Node
mapping node. This fixes problems on systems where the order
of SRAT entries does not match the MADT.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

While booting with SMT disabled in bios, when using acpi srat to setup
cpu_to_node[], sparse apic_ids create problems.

Without this patch, intel x86_64 boxes with hyperthreading disabled in the
bios (and which rely on srat for numa setup) endup having incorrect values in
cpu_to_node[] arrays, causing sched domains to be built incorrectly etc.
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

From: Keith Manning

Print a boot message for hotplug memory zones
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!