GitLab

Update CHANGELOG for release.
Signed-off-by: Wolfgang Denk <wd@denx.de>

Jean-Christophe PLAGNIOL-VILLARD authored Mar 09, 2008 and Wolfgang Denk committed Mar 09, 2008

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>

Jean-Christophe PLAGNIOL-VILLARD authored Mar 09, 2008 and Wolfgang Denk committed Mar 09, 2008

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: Wolfgang Denk <wd@denx.de>

and get rid of a couple of unneeded casts.
Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Wolfgang Denk <wd@denx.de>

and simplify Makefile a bit.
Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Jean-Christophe PLAGNIOL-VILLARD authored Mar 08, 2008 and Wolfgang Denk committed Mar 08, 2008

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Nobuhiro Iwamatsu authored Mar 08, 2008 and Wolfgang Denk committed Mar 08, 2008

When rtl_recv() of rtl8169 is called, OWNbit of status register
is not enable occasionally.
rtl_recv() doesn't work normally when the driver doesn't do
appropriate processing.
This patch fix this problem.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Heiko Schocher authored Mar 07, 2008 and Wolfgang Denk committed Mar 08, 2008

initialize the UPIOx controller.
Signed-off-by: Heiko Schocher <hs@denx.de>

Heiko Schocher authored Mar 07, 2008 and Wolfgang Denk committed Mar 08, 2008

add support for the config Flash.
initialize the UPIOx controller.
Signed-off-by: Heiko Schocher <hs@denx.de>

the dts file basenames were updated in linux - this helps avoid
inadvertently loading any old dtbs laying around.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

allow u-boot to recover (and, e.g., switch to another interface) in the
case where a PHY does not report autonegotiation is complete within its
two second timeout value.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

Markus Brunner authored Mar 05, 2008 and Stefan Roese committed Mar 07, 2008

The taihu board used gpio_read_out_bit which reads the output register and not
the pin state.
Signed-off-by: Markus Brunner <super.firetwister@gmail.com>

Signed-off-by: Stefan Roese <sr@denx.de>

Dave Liu authored Mar 04, 2008 and Wolfgang Denk committed Mar 07, 2008

1. Make the CSB bus pipeline depth as 4, and enable
   the repeat mode;
2. Raise the eTSEC emergency priority;
3. Use the highest IP blocks clock.
Signed-off-by: Dave Liu <daveliu@freescale.com>

Detlev Zundel authored Mar 06, 2008 and Wolfgang Denk committed Mar 06, 2008

The latter version stops when "run load" fails for whatever reasons
rendering the combination *a lot* more secure.
Signed-off-by: Detlev Zundel <dzu@denx.de>

Stefan Roese authored Mar 04, 2008 and Wolfgang Denk committed Mar 05, 2008

This patch fixes a problem seen on PPC4xx boards, when no MAC address is
defined. Then no ethernet interface is available but a simple "tftp"
command will return without any error message which is quite confusing.
Signed-off-by: Stefan Roese <sr@denx.de>

Jon Loeliger authored Mar 04, 2008 and Wolfgang Denk committed Mar 05, 2008

Many of the spd.h #includers don't need it,
and wanted to have spd_sdram() declared instead.
Since they didn't get that, some also had open
coded extern declarations of it instead or as well.
Fix it all up by using spd_sdram.h where needed.
Signed-off-by: Jon Loeliger <jdl@freescale.com>

Signed-off-by: Wolfgang Denk <wd@denx.de>

This patch fixes a problem seen on PPC4xx boards, when no MAC address is
defined. Then no ethernet interface is available but a simple "tftp"
command will return without any error message which is quite confusing.
Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Commit 5013c09f

 (Makefile: cleanup "clean" target) introduced a
problem for out-of-tree builds which caused "make clean" to fail.
Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Mike Nuss authored Mar 03, 2008 and Wolfgang Denk committed Mar 04, 2008

Every now and then a Sequoia board (or equivalent hardware) had
problems connecting to a Gigabit capable network interface.

There were differences in the PHY setup between Linux and U-Boot.

This patch fixes the problem. Apparently "remote fault" is being set,
which signals to some devices (on the other end of the cable) that a
fault has occurred, while other devices ignore it. I believe the RF bit
was causing the issue, but I removed T4 also, to match up with Linux.
Signed-off-by: Mike Nuss <mike@terascala.com>

Timur Tabi authored Mar 03, 2008 and Wolfgang Denk committed Mar 03, 2008

Fix a typo in qe_upload_firmware() that prevented uploading firmware on
systems with more than one RISC core.
Signed-off-by: Timur Tabi <timur@freescale.com>

Bernhard Nemec authored Mar 03, 2008 and Wolfgang Denk committed Mar 03, 2008

Originally pointed out by Laurent Pinchart <laurent.pinchart@tbox.biz>,
see http://thread.gmane.org/gmane.comp.boot-loaders.u-boot/22846

Signed-off-by: Bernhard Nemec <bnemec <at> ganssloser.com>

Kim B. Heino authored Mar 03, 2008 and Wolfgang Denk committed Mar 03, 2008

If I try to "cp.b <ram> <dataflash>", u-boot selects normal flash
routines instead of dataflash. This is because it checks "if source
address is not dataflash" instead of target address.
Signed-off-by: Kim B. Heino <Kim.Heino@bluegiga.com>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Jean-Christophe PLAGNIOL-VILLARD authored Mar 02, 2008 and Wolfgang Denk committed Mar 03, 2008

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>