ARM: dts: stm32: Add STM32MP257F Evaluation board support

Add STM32MP257F Evaluation board support. It embeds a STM32MP257FAI SoC,
with 4GB of DDR4, TSN switch (2+1 ports), 2*USB typeA, 1*USB2 typeC,
SNOR OctoSPI, mini PCIe, STPMIC2 for power distribution ...

Sync device tree with kernel v6.6-rc1.

Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>

arch/arm/dts/Makefile

@@ -1352,6 +1352,9 @@ dtb-$(CONFIG_STM32MP15x) += \
 	stm32mp15xx-dhcor-drc-compact.dtb \
 	stm32mp15xx-dhcor-testbench.dtb
 
+dtb-$(CONFIG_STM32MP25X) += \
+	stm32mp257f-ev1.dtb
+
 dtb-$(CONFIG_SOC_K3_AM654) += \
 	k3-am654-base-board.dtb \
 	k3-am654-r5-base-board.dtb \

arch/arm/dts/stm32mp25-pinctrl.dtsi

+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2023 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+#include <dt-bindings/pinctrl/stm32-pinfunc.h>
+
+&pinctrl {
+	usart2_pins_a: usart2-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('A', 4, AF6)>; /* USART2_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('A', 8, AF8)>; /* USART2_RX */
+			bias-disable;
+		};
+	};
+
+	usart2_idle_pins_a: usart2-idle-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('A', 4, ANALOG)>; /* USART2_TX */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('A', 8, AF8)>; /* USART2_RX */
+			bias-disable;
+		};
+	};
+
+	usart2_sleep_pins_a: usart2-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 4, ANALOG)>, /* USART2_TX */
+				 <STM32_PINMUX('A', 8, ANALOG)>; /* USART2_RX */
+		};
+	};
+};

arch/arm/dts/stm32mp25-u-boot.dtsi

+// SPDX-License-Identifier: GPL-2.0-or-later OR BSD-3-Clause
+/*
+ * Copyright : STMicroelectronics 2023
+ */
+
+/ {
+	aliases {
+		gpio0 = &gpioa;
+		gpio1 = &gpiob;
+		gpio2 = &gpioc;
+		gpio3 = &gpiod;
+		gpio4 = &gpioe;
+		gpio5 = &gpiof;
+		gpio6 = &gpiog;
+		gpio7 = &gpioh;
+		gpio8 = &gpioi;
+		gpio9 = &gpioj;
+		gpio10 = &gpiok;
+		gpio25 = &gpioz;
+		pinctrl0 = &pinctrl;
+		pinctrl1 = &pinctrl_z;
+	};
+
+	firmware {
+		optee {
+			bootph-all;
+		};
+	};
+
+	/* need PSCI for sysreset during board_f */
+	psci {
+		bootph-all;
+	};
+
+	soc@0 {
+		bootph-all;
+	};
+};
+
+&gpioa {
+	bootph-all;
+};
+
+&gpiob {
+	bootph-all;
+};
+
+&gpioc {
+	bootph-all;
+};
+
+&gpiod {
+	bootph-all;
+};
+
+&gpioe {
+	bootph-all;
+};
+
+&gpiof {
+	bootph-all;
+};
+
+&gpiog {
+	bootph-all;
+};
+
+&gpioh {
+	bootph-all;
+};
+
+&gpioi {
+	bootph-all;
+};
+
+&gpioj {
+	bootph-all;
+};
+
+&gpiok {
+	bootph-all;
+};
+
+&gpioz {
+	bootph-all;
+};
+
+&pinctrl {
+	bootph-all;
+};
+
+&rifsc {
+	bootph-all;
+};
+
+&scmi_clk {
+	bootph-all;
+};
+
+&syscfg {
+	bootph-all;
+};

arch/arm/dts/stm32mp251.dtsi

+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2023 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a35";
+			device_type = "cpu";
+			reg = <0>;
+			enable-method = "psci";
+		};
+	};
+
+	arm-pmu {
+		compatible = "arm,cortex-a35-pmu";
+		interrupts = <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>;
+		interrupt-parent = <&intc>;
+	};
+
+	arm_wdt: watchdog {
+		compatible = "arm,smc-wdt";
+		arm,smc-id = <0xb200005a>;
+		status = "disabled";
+	};
+
+	clocks {
+		ck_flexgen_08: ck-flexgen-08 {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <100000000>;
+		};
+
+		ck_flexgen_51: ck-flexgen-51 {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <200000000>;
+		};
+
+		ck_icn_ls_mcu: ck-icn-ls-mcu {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <200000000>;
+		};
+	};
+
+	firmware {
+		optee {
+			compatible = "linaro,optee-tz";
+			method = "smc";
+		};
+
+		scmi {
+			compatible = "linaro,scmi-optee";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			linaro,optee-channel-id = <0>;
+
+			scmi_clk: protocol@14 {
+				reg = <0x14>;
+				#clock-cells = <1>;
+			};
+
+			scmi_reset: protocol@16 {
+				reg = <0x16>;
+				#reset-cells = <1>;
+			};
+		};
+	};
+
+	intc: interrupt-controller@4ac00000 {
+		compatible = "arm,cortex-a7-gic";
+		#interrupt-cells = <3>;
+		#address-cells = <1>;
+		interrupt-controller;
+		reg = <0x0 0x4ac10000 0x0 0x1000>,
+		      <0x0 0x4ac20000 0x0 0x2000>,
+		      <0x0 0x4ac40000 0x0 0x2000>,
+		      <0x0 0x4ac60000 0x0 0x2000>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupt-parent = <&intc>;
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+		always-on;
+	};
+
+	soc@0 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		interrupt-parent = <&intc>;
+		ranges = <0x0 0x0 0x0 0x80000000>;
+
+		rifsc: rifsc-bus@42080000 {
+			compatible = "simple-bus";
+			reg = <0x42080000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			usart2: serial@400e0000 {
+				compatible = "st,stm32h7-uart";
+				reg = <0x400e0000 0x400>;
+				interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&ck_flexgen_08>;
+				status = "disabled";
+			};
+		};
+
+		syscfg: syscon@44230000 {
+			compatible = "st,stm32mp25-syscfg", "syscon";
+			reg = <0x44230000 0x10000>;
+		};
+
+		pinctrl: pinctrl@44240000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "st,stm32mp257-pinctrl";
+			ranges = <0 0x44240000 0xa0400>;
+			pins-are-numbered;
+
+			gpioa: gpio@44240000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x0 0x400>;
+				clocks = <&ck_icn_ls_mcu>;
+				st,bank-name = "GPIOA";
+				status = "disabled";
+			};
+
+			gpiob: gpio@44250000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x10000 0x400>;
+				clocks = <&ck_icn_ls_mcu>;
+				st,bank-name = "GPIOB";
+				status = "disabled";
+			};
+
+			gpioc: gpio@44260000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x20000 0x400>;
+				clocks = <&ck_icn_ls_mcu>;
+				st,bank-name = "GPIOC";
+				status = "disabled";
+			};
+
+			gpiod: gpio@44270000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x30000 0x400>;
+				clocks = <&ck_icn_ls_mcu>;
+				st,bank-name = "GPIOD";
+				status = "disabled";
+			};
+
+			gpioe: gpio@44280000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x40000 0x400>;
+				clocks = <&ck_icn_ls_mcu>;
+				st,bank-name = "GPIOE";
+				status = "disabled";
+			};
+
+			gpiof: gpio@44290000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x50000 0x400>;
+				clocks = <&ck_icn_ls_mcu>;
+				st,bank-name = "GPIOF";
+				status = "disabled";
+			};
+
+			gpiog: gpio@442a0000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x60000 0x400>;
+				clocks = <&ck_icn_ls_mcu>;
+				st,bank-name = "GPIOG";
+				status = "disabled";
+			};
+
+			gpioh: gpio@442b0000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x70000 0x400>;
+				clocks = <&ck_icn_ls_mcu>;
+				st,bank-name = "GPIOH";
+				status = "disabled";
+			};
+
+			gpioi: gpio@442c0000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x80000 0x400>;
+				clocks = <&ck_icn_ls_mcu>;
+				st,bank-name = "GPIOI";
+				status = "disabled";
+			};
+
+			gpioj: gpio@442d0000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x90000 0x400>;
+				clocks = <&ck_icn_ls_mcu>;
+				st,bank-name = "GPIOJ";
+				status = "disabled";
+			};
+
+			gpiok: gpio@442e0000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0xa0000 0x400>;
+				clocks = <&ck_icn_ls_mcu>;
+				st,bank-name = "GPIOK";
+				status = "disabled";
+			};
+		};
+
+		pinctrl_z: pinctrl@46200000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "st,stm32mp257-z-pinctrl";
+			ranges = <0 0x46200000 0x400>;
+			pins-are-numbered;
+
+			gpioz: gpio@46200000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0 0x400>;
+				clocks = <&ck_icn_ls_mcu>;
+				st,bank-name = "GPIOZ";
+				st,bank-ioport = <11>;
+				status = "disabled";
+			};
+
+		};
+	};
+};

arch/arm/dts/stm32mp253.dtsi

+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2023 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+#include "stm32mp251.dtsi"
+
+/ {
+	cpus {
+		cpu1: cpu@1 {
+			compatible = "arm,cortex-a35";
+			device_type = "cpu";
+			reg = <1>;
+			enable-method = "psci";
+		};
+	};
+
+	arm-pmu {
+		interrupts = <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>;
+	};
+};

arch/arm/dts/stm32mp255.dtsi

+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2023 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+#include "stm32mp253.dtsi"
+
+/ {
+};

arch/arm/dts/stm32mp257.dtsi

+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2023 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+#include "stm32mp255.dtsi"
+
+/ {
+};

arch/arm/dts/stm32mp257f-ev1-u-boot.dtsi

+// SPDX-License-Identifier: GPL-2.0-or-later OR BSD-3-Clause
+/*
+ * Copyright (C) STMicroelectronics 2023 - All Rights Reserved
+ */
+
+#include "stm32mp25-u-boot.dtsi"
+
+&usart2 {
+	bootph-all;
+};
+
+&usart2_pins_a {
+	bootph-all;
+	pins1 {
+		bootph-all;
+	};
+	pins2 {
+		bootph-all;
+	};
+};

arch/arm/dts/stm32mp257f-ev1.dts

+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2023 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+/dts-v1/;
+
+#include "stm32mp257.dtsi"
+#include "stm32mp25xf.dtsi"
+#include "stm32mp25-pinctrl.dtsi"
+#include "stm32mp25xxai-pinctrl.dtsi"
+
+/ {
+	model = "STMicroelectronics STM32MP257F-EV1 Evaluation Board";
+	compatible = "st,stm32mp257f-ev1", "st,stm32mp257";
+
+	aliases {
+		serial0 = &usart2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x0 0x80000000 0x1 0x0>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		fw@80000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x80000000 0x0 0x4000000>;
+			no-map;
+		};
+	};
+};
+
+&arm_wdt {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&usart2 {
+	pinctrl-names = "default", "idle", "sleep";
+	pinctrl-0 = <&usart2_pins_a>;
+	pinctrl-1 = <&usart2_idle_pins_a>;
+	pinctrl-2 = <&usart2_sleep_pins_a>;
+	status = "okay";
+};

arch/arm/dts/stm32mp25xc.dtsi

+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2023 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+/ {
+};

arch/arm/dts/stm32mp25xf.dtsi

+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2023 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+/ {
+};

arch/arm/dts/stm32mp25xxai-pinctrl.dtsi

+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2023 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+&pinctrl {
+	st,package = <STM32MP_PKG_AI>;
+
+	gpioa: gpio@44240000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 0 16>;
+	};
+
+	gpiob: gpio@44250000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 16 16>;
+	};
+
+	gpioc: gpio@44260000 {
+		status = "okay";
+		ngpios = <14>;
+		gpio-ranges = <&pinctrl 0 32 14>;
+	};
+
+	gpiod: gpio@44270000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 48 16>;
+	};
+
+	gpioe: gpio@44280000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 64 16>;
+	};
+
+	gpiof: gpio@44290000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 80 16>;
+	};
+
+	gpiog: gpio@442a0000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 96 16>;
+	};
+
+	gpioh: gpio@442b0000 {
+		status = "okay";
+		ngpios = <12>;
+		gpio-ranges = <&pinctrl 2 114 12>;
+	};
+
+	gpioi: gpio@442c0000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 128 16>;
+	};
+
+	gpioj: gpio@442d0000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 144 16>;
+	};
+
+	gpiok: gpio@442e0000 {
+		status = "okay";
+		ngpios = <8>;
+		gpio-ranges = <&pinctrl 0 160 8>;
+	};
+};
+
+&pinctrl_z {
+	gpioz: gpio@46200000 {
+		status = "okay";
+		ngpios = <10>;
+		gpio-ranges = <&pinctrl_z 0 400 10>;
+	};
+};

arch/arm/dts/stm32mp25xxak-pinctrl.dtsi

+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2023 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+&pinctrl {
+	st,package = <STM32MP_PKG_AK>;
+
+	gpioa: gpio@44240000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 0 16>;
+	};
+
+	gpiob: gpio@44250000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 16 16>;
+	};
+
+	gpioc: gpio@44260000 {
+		status = "okay";
+		ngpios = <14>;
+		gpio-ranges = <&pinctrl 0 32 14>;
+	};
+
+	gpiod: gpio@44270000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 48 16>;
+	};
+
+	gpioe: gpio@44280000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 64 16>;
+	};
+
+	gpiof: gpio@44290000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 80 16>;
+	};
+
+	gpiog: gpio@442a0000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 96 16>;
+	};
+
+	gpioh: gpio@442b0000 {
+		status = "okay";
+		ngpios = <12>;
+		gpio-ranges = <&pinctrl 2 114 12>;
+	};
+
+	gpioi: gpio@442c0000 {
+		status = "okay";
+		ngpios = <12>;
+		gpio-ranges = <&pinctrl 0 128 12>;
+	};
+};
+
+&pinctrl_z {
+	gpioz: gpio@46200000 {
+		status = "okay";
+		ngpios = <10>;
+		gpio-ranges = <&pinctrl_z 0 400 10>;
+	};
+};

arch/arm/dts/stm32mp25xxal-pinctrl.dtsi

+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2023 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+&pinctrl {
+	st,package = <STM32MP_PKG_AL>;
+
+	gpioa: gpio@44240000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 0 16>;
+	};
+
+	gpiob: gpio@44250000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 16 16>;
+	};
+
+	gpioc: gpio@44260000 {
+		status = "okay";
+		ngpios = <14>;
+		gpio-ranges = <&pinctrl 0 32 14>;
+	};
+
+	gpiod: gpio@44270000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 48 16>;
+	};
+
+	gpioe: gpio@44280000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 64 16>;
+	};
+
+	gpiof: gpio@44290000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 80 16>;
+	};
+
+	gpiog: gpio@442a0000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 96 16>;
+	};
+
+	gpioh: gpio@442b0000 {
+		status = "okay";
+		ngpios = <12>;
+		gpio-ranges = <&pinctrl 2 114 12>;
+	};
+
+	gpioi: gpio@442c0000 {
+		status = "okay";
+		ngpios = <12>;
+		gpio-ranges = <&pinctrl 0 128 12>;
+	};
+};
+
+&pinctrl_z {
+	gpioz: gpio@46200000 {
+		status = "okay";
+		ngpios = <10>;
+		gpio-ranges = <&pinctrl_z 0 400 10>;
+	};
+};

include/dt-bindings/pinctrl/stm32-pinfunc.h

@@ -37,6 +37,9 @@
 #define STM32MP_PKG_AB	0x2
 #define STM32MP_PKG_AC	0x4
 #define STM32MP_PKG_AD	0x8
+#define STM32MP_PKG_AI	0x100
+#define STM32MP_PKG_AK	0x400
+#define STM32MP_PKG_AL	0x800
 
 #endif /* _DT_BINDINGS_STM32_PINFUNC_H */