Commit 3551b24f authored by Hans de Goede's avatar Hans de Goede
Browse files

sunxi: Add defconfig and dts file for inet86dz board



The inet86dz board is a board used in 7" tablets from various oems.

These tablets are a23 based 7" tablets featuring a 1024x600 LCD,
512MB RAM, 4G NAND, rtl8188etv usb wifi, gsl1680 touchschreen,
micro-sd slot, 3.5mm headphone jack and a micro-usb otg connector
which doubles as charging port.

The dts file this commit adds is identical to the one submitted to
the upstream kernel.
Signed-off-by: default avatarHans de Goede <hdegoede@redhat.com>
Acked-by: default avatarIan Campbell <ijc@hellion.org.uk>
parent cd38e3d1
......@@ -223,6 +223,7 @@ dtb-$(CONFIG_MACH_SUN7I) += \
dtb-$(CONFIG_MACH_SUN8I_A23) += \
sun8i-a23-evb.dtb \
sun8i-a23-gt90h-v4.dtb \
sun8i-a23-inet86dz.dtb \
sun8i-a23-polaroid-mid2407pxe03.dtb \
sun8i-a23-polaroid-mid2809pxe04.dtb \
sun8i-a23-q8-tablet.dtb
......
/*
* Copyright 2016 Hans de Goede <hdegoede@redhat.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "sun8i-a23.dtsi"
#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
#include <dt-bindings/pwm/pwm.h>
/ {
model = "INet-86DZ Rev 01";
compatible = "primux,inet86dz", "allwinner,sun8i-a23";
aliases {
serial0 = &r_uart;
};
backlight: backlight {
compatible = "pwm-backlight";
pinctrl-names = "default";
pinctrl-0 = <&bl_en_pin_inet86dz>;
pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
default-brightness-level = <8>;
enable-gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
};
chosen {
stdout-path = "serial0:115200n8";
};
};
&ehci0 {
status = "okay";
};
&i2c0 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
/*
* The gsl1680 is rated at 400KHz and it will not work reliable at
* 100KHz, this has been confirmed on multiple different tablets.
* The gsl1680 is the only device on this bus.
*/
clock-frequency = <400000>;
gsl1680: touchscreen@40 {
compatible = "silead,gsl1680";
reg = <0x40>;
interrupt-parent = <&pio>;
interrupts = <1 5 IRQ_TYPE_EDGE_FALLING>; /* PB5 */
pinctrl-names = "default";
pinctrl-0 = <&ts_power_pin_inet86dz>;
power-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
touchscreen-size-x = <960>;
touchscreen-size-y = <640>;
touchscreen-max-fingers = <5>;
touchscreen-fw-name = "silead/gsl1680-inet86dz.fw";
};
};
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
};
&lradc {
vref-supply = <&reg_vcc3v0>;
status = "okay";
button@200 {
label = "Volume Up";
linux,code = <KEY_VOLUMEUP>;
channel = <0>;
voltage = <200000>;
};
button@400 {
label = "Volume Down";
linux,code = <KEY_VOLUMEDOWN>;
channel = <0>;
voltage = <400000>;
};
};
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_inet86dz>;
vmmc-supply = <&reg_dcdc1>;
bus-width = <4>;
cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
cd-inverted;
status = "okay";
};
&pio {
bl_en_pin_inet86dz: bl_en_pin@0 {
allwinner,pins = "PH6";
allwinner,function = "gpio_in";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
mmc0_cd_pin_inet86dz: mmc0_cd_pin@0 {
allwinner,pins = "PB4";
allwinner,function = "gpio_in";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
};
ts_power_pin_inet86dz: ts_power_pin@0 {
allwinner,pins = "PH1";
allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
usb0_id_detect_pin: usb0_id_detect_pin@0 {
allwinner,pins = "PH8";
allwinner,function = "gpio_in";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
};
};
&pwm {
pinctrl-names = "default";
pinctrl-0 = <&pwm0_pins>;
status = "okay";
};
&r_rsb {
status = "okay";
axp22x: pmic@3a3 {
compatible = "x-powers,axp223";
reg = <0x3a3>;
interrupt-parent = <&nmi_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
eldoin-supply = <&reg_dcdc1>;
x-powers,drive-vbus-en;
};
};
&r_uart {
pinctrl-names = "default";
pinctrl-0 = <&r_uart_pins_a>;
status = "okay";
};
#include "axp22x.dtsi"
&reg_aldo1 {
regulator-always-on;
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-name = "vcc-io";
};
&reg_aldo2 {
regulator-always-on;
regulator-min-microvolt = <2350000>;
regulator-max-microvolt = <2650000>;
regulator-name = "vdd-dll";
};
&reg_aldo3 {
regulator-always-on;
regulator-min-microvolt = <2700000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc-pll-avcc";
};
&reg_dc1sw {
regulator-name = "vcc-lcd";
};
&reg_dc5ldo {
regulator-always-on;
regulator-min-microvolt = <900000>;
regulator-max-microvolt = <1400000>;
regulator-name = "vdd-cpus";
};
&reg_dcdc1 {
regulator-always-on;
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-name = "vcc-3v0";
};
&reg_dcdc2 {
regulator-always-on;
regulator-min-microvolt = <900000>;
regulator-max-microvolt = <1400000>;
regulator-name = "vdd-sys";
};
&reg_dcdc3 {
regulator-always-on;
regulator-min-microvolt = <900000>;
regulator-max-microvolt = <1400000>;
regulator-name = "vdd-cpu";
};
&reg_dcdc5 {
regulator-always-on;
regulator-min-microvolt = <1500000>;
regulator-max-microvolt = <1500000>;
regulator-name = "vcc-dram";
};
&reg_dldo1 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc-wifi";
};
&reg_drivevbus {
regulator-name = "usb0-vbus";
status = "okay";
};
&reg_rtc_ldo {
regulator-name = "vcc-rtc";
};
&simplefb_lcd {
vcc-lcd-supply = <&reg_dc1sw>;
};
&usb_otg {
dr_mode = "otg";
status = "okay";
};
&usb_power_supply {
status = "okay";
};
&usbphy {
pinctrl-names = "default";
pinctrl-0 = <&usb0_id_detect_pin>;
usb0_id_det-gpio = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */
usb0_vbus_power-supply = <&usb_power_supply>;
usb0_vbus-supply = <&reg_drivevbus>;
usb1_vbus-supply = <&reg_dldo1>;
status = "okay";
};
......@@ -54,6 +54,7 @@ F: configs/Wits_Pro_A20_DKT_defconfig
F: include/configs/sun8i.h
F: configs/ga10h_v1_1_defconfig
F: configs/gt90h_v4_defconfig
F: configs/inet86dz_defconfig
F: configs/orangepi_2_defconfig
F: configs/orangepi_one_defconfig
F: configs/orangepi_pc_defconfig
......
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_MACH_SUN8I_A23=y
CONFIG_DRAM_CLK=552
CONFIG_DRAM_ZQ=63351
CONFIG_MMC0_CD_PIN="PB4"
CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
CONFIG_USB0_ID_DET="PH8"
CONFIG_AXP_GPIO=y
CONFIG_VIDEO_LCD_MODE="x:1024,y:600,depth:18,pclk_khz:51000,le:138,ri:162,up:22,lo:10,hs:20,vs:3,sync:3,vmode:0"
CONFIG_VIDEO_LCD_DCLK_PHASE=0
CONFIG_VIDEO_LCD_POWER="PH7"
CONFIG_VIDEO_LCD_BL_EN="PH6"
CONFIG_VIDEO_LCD_BL_PWM="PH0"
CONFIG_DEFAULT_DEVICE_TREE="sun8i-a23-inet86dz"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=5"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
CONFIG_AXP_DLDO1_VOLT=3300
CONFIG_USB_MUSB_HOST=y
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment