Commit c1cfd519 authored by Hans de Goede's avatar Hans de Goede
Browse files

sunxi: Display: Add support for eDP panels connected via an anx9804 bridge



Add support for 4 1.62G lane eDP panels connected via an anx9804 bridge,
such as found on the Colombus devkit.

While at it also fix the wrong indentation of the SSD2828 Kconfig help text
in board/sunxi/Kconfig.
Signed-off-by: default avatarHans de Goede <hdegoede@redhat.com>
Acked-by: default avatarIan Campbell <ijc@hellion.org.uk>
parent 66525bb7
......@@ -526,7 +526,16 @@ config VIDEO_LCD_PANEL_MIPI_4_LANE_513_MBPS_VIA_SSD2828
select VIDEO_LCD_SSD2828
select VIDEO_LCD_IF_PARALLEL
---help---
7.85" 768x1024 LCD panels, such as LG LP079X01 or AUO B079XAN01.0
7.85" 768x1024 LCD panels, such as LG LP079X01 or AUO B079XAN01.0
config VIDEO_LCD_PANEL_EDP_4_LANE_1620M_VIA_ANX9804
bool "eDP 4-lane, 1.62G LCD panel via ANX9804 bridge chip"
select VIDEO_LCD_ANX9804
select VIDEO_LCD_IF_PARALLEL
select VIDEO_LCD_PANEL_I2C
---help---
Select this for eDP LCD panels with 4 lanes running at 1.62G,
connected via an ANX9804 bridge chip.
config VIDEO_LCD_PANEL_HITACHI_TX18D42VM
bool "Hitachi tx18d42vm LCD panel"
......
......@@ -4,6 +4,16 @@ CONFIG_MACH_SUN6I=y
CONFIG_DRAM_CLK=240
CONFIG_DRAM_ZQ=251
CONFIG_USB1_VBUS_PIN=""
CONFIG_I2C0_ENABLE=y
CONFIG_AXP_GPIO=y
CONFIG_VIDEO_LCD_MODE="x:2048,y:1536,depth:24,pclk_khz:208000,le:5,ri:150,up:9,lo:24,hs:5,vs:1,sync:3,vmode:0"
CONFIG_VIDEO_LCD_DCLK_PHASE=0
CONFIG_VIDEO_LCD_POWER="PH27"
CONFIG_VIDEO_LCD_BL_EN="PM1"
CONFIG_VIDEO_LCD_BL_PWM="PH13"
CONFIG_VIDEO_LCD_PANEL_I2C_SDA="PA23"
CONFIG_VIDEO_LCD_PANEL_I2C_SCL="PA24"
CONFIG_VIDEO_LCD_PANEL_EDP_4_LANE_1620M_VIA_ANX9804=y
CONFIG_DEFAULT_DEVICE_TREE="sun6i-a31-colombus"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
......@@ -13,4 +23,5 @@ CONFIG_SYS_EXTRA_OPTIONS="SUNXI_GMAC,RGMII"
# CONFIG_CMD_FPGA is not set
CONFIG_ETH_DESIGNWARE=y
CONFIG_AXP221_ALDO1_VOLT=3300
CONFIG_AXP221_ELDO3_VOLT=1800
CONFIG_USB_EHCI_HCD=y
......@@ -15,6 +15,7 @@
#include <asm/global_data.h>
#include <asm/gpio.h>
#include <asm/io.h>
#include <axp221.h>
#include <errno.h>
#include <fdtdec.h>
#include <fdt_support.h>
......@@ -22,6 +23,7 @@
#include <malloc.h>
#include <video_fb.h>
#include "videomodes.h"
#include "anx9804.h"
#include "hitachi_tx18d42vm_lcd.h"
#include "ssd2828.h"
......@@ -765,13 +767,17 @@ static void sunxi_lcdc_tcon0_mode_set(const struct ctfb_res_modes *mode,
(struct sunxi_lcdc_reg *)SUNXI_LCD0_BASE;
int bp, clk_delay, clk_div, clk_double, pin, total, val;
for (pin = SUNXI_GPD(0); pin <= SUNXI_GPD(27); pin++)
for (pin = SUNXI_GPD(0); pin <= SUNXI_GPD(27); pin++) {
#ifdef CONFIG_VIDEO_LCD_IF_PARALLEL
sunxi_gpio_set_cfgpin(pin, SUNXI_GPD_LCD0);
#endif
#ifdef CONFIG_VIDEO_LCD_IF_LVDS
sunxi_gpio_set_cfgpin(pin, SUNXI_GPD_LVDS0);
#endif
#ifdef CONFIG_VIDEO_LCD_PANEL_EDP_4_LANE_1620M_VIA_ANX9804
sunxi_gpio_set_drv(pin, 3);
#endif
}
sunxi_lcdc_pll_set(0, mode->pixclock_khz, &clk_div, &clk_double);
......@@ -1208,6 +1214,17 @@ static void sunxi_mode_set(const struct ctfb_res_modes *mode,
break;
case sunxi_monitor_lcd:
sunxi_lcdc_panel_enable();
if (IS_ENABLED(CONFIG_VIDEO_LCD_PANEL_EDP_4_LANE_1620M_VIA_ANX9804)) {
/*
* The anx9804 needs 1.8V from eldo3, we do this here
* and not via CONFIG_AXP221_ELDO3 from board_init()
* to avoid turning this on when using hdmi output.
*/
axp221_set_eldo(3, 1800);
anx9804_init(CONFIG_VIDEO_LCD_I2C_BUS, 4,
ANX9804_DATA_RATE_1620M,
sunxi_display.depth);
}
if (IS_ENABLED(CONFIG_VIDEO_LCD_HITACHI_TX18D42VM)) {
mdelay(50); /* Wait for lcd controller power on */
hitachi_tx18d42vm_init();
......
......@@ -288,7 +288,11 @@ extern int soft_i2c_gpio_scl;
* The amount of RAM to keep free at the top of RAM when relocating u-boot,
* to use as framebuffer. This must be a multiple of 4096.
*/
#ifdef CONFIG_VIDEO_LCD_PANEL_EDP_4_LANE_1620M_VIA_ANX9804
#define CONFIG_SUNXI_MAX_FB_SIZE (12 << 20)
#else
#define CONFIG_SUNXI_MAX_FB_SIZE (9 << 20)
#endif
/* Do we want to initialize a simple FB? */
#define CONFIG_VIDEO_DT_SIMPLEFB
......
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment