Ryan Mallon authored Jan 27, 2011 and Heiko Schocher committed Jan 27, 2011

Make at91 header includes in soft_i2c depend only on CONFIG_AT91FAMILY
rather than individual SoCs.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Reinhard Meyer<u-boot@emk-elektronik.de>

Macpaul Lin authored Jan 05, 2011 and Wolfgang Denk committed Jan 25, 2011

Faraday's ftpmu010 is a power managemnet unit which support cpu
sleep and frequency scaling. It has been integrated into many SoC.

This patch also move ftpmu010 to a proper place for later enhancement.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>

Kumar Gala authored Jan 19, 2011 and Wolfgang Denk committed Jan 25, 2011

Patch 8ef583a0

 [miiphy: convert to linux/mii.h] introduced the following
compiler warnings in the uec ethernet driver:

In file included from /local/home/galak/git/u-boot-85xx/include/miiphy.h:37:0,
                 from uec.c:32:
/local/home/galak/git/u-boot-85xx/include/linux/mii.h:133:0: warning: "LPA_1000FULL" redefined
uec_phy.h:34:0: note: this is the location of the previous definition
/local/home/galak/git/u-boot-85xx/include/linux/mii.h:134:0: warning: "LPA_1000HALF" redefined
uec_phy.h:35:0: note: this is the location of the previous definition
In file included from /local/home/galak/git/u-boot-85xx/include/miiphy.h:37:0,
                 from uec_phy.c:27:
/local/home/galak/git/u-boot-85xx/include/linux/mii.h:133:0: warning: "LPA_1000FULL" redefined
uec_phy.h:34:0: note: this is the location of the previous definition
/local/home/galak/git/u-boot-85xx/include/linux/mii.h:134:0: warning: "LPA_1000HALF" redefined
uec_phy.h:35:0: note: this is the location of the previous definition

Fix them be removing the duplication in the uec code and utlizing the
linux/mii.h version instead.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Add new headers that capture common defines for a given SoC/processor
rather than duplicating that information in board config.h and random
other places.

Eventually this should be handled by Kconfig & defconfigs
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>

Add P2040 SoC specific information:
* SERDES Table
* Added p2040 to cpu_type_list and SVR list
* Added number of LAWs for p2040
* Set CONFIG_MAX_CPUS to 4 for p2040
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

The P1014 is similar to the P1010 processor with the following differences:

- 16bit DDR with ECC. (P1010 has 32bit DDR w/o ECC)
- no eCAN interface. (P1010 has 2 eCAN interfaces)
- Two SGMII interface (P1010 has 3 SGMII)
- No secure boot
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Key Features include of the P1010:
* e500v2 core frequency operation of 500 to 800 MHz
* Power consumption less than 5.0 W at 800 MHz core speed
* Dual SATA 3 Gbps controllers with integrated PHY
* Dual PCI Express controllers
* Three 10/100/1000 Mbps enhanced triple-speed Ethernet controllers (eTSECs)
	* TCP/IP acceleration and classification capabilities
	* IEEE 1588 support
	* Lossless flow control
	* RGMII, SGMII
* DDR3 with support for a 32-bit data interface (40 bits including ECC),
  up to 800 MHz data rate 32/16-bit DDR3 memory controller
* Dedicated security engine featuring trusted boot
* TDM interface
* Dual controller area networks (FlexCAN) controller
* SD/MMC card controller supporting booting from Flash cards
* USB 2.0 host and device controller with an on-chip, high-speed PHY
* Integrated Flash controller (IFC)
* Power Management Controller (PMC)
* Four-channel, general-purpose DMA controller
* I2C controller
* Serial peripheral interface (SPI) controller with master and slave support
* System timers including a periodic interrupt timer, real-time clock,
  software watchdog timer, and four general-purpose timers
* Dual DUARTs
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

This allows to change device and host MAC addresses without performing
reset.
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>

Calling eth_bind at usb_eth_init time causes renaming of the network
device from 'usb_ether' to 'usb0'. Fixing this to keep the first name.
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>

Since the ether may not be the only one usb gadget would be used
in the uboot, it is neccessary to do the register each time the
eth begin to work to make usb gadget driver less confussed when
we want to use two different usb gadget at the same time.

Usb gadget driver could simple ignore the register operation, if
it find the driver has been registered already.
Signed-off-by: Lei Wen <leiwen@marvell.com>

Peter Tyser authored Dec 28, 2010 and Wolfgang Denk committed Jan 19, 2011

There's no compelling reason to have the output on bootup or the
"flinfo" command print "flash" in uppercase, so use the proper case
where appropriate.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>

Yanjun Yang authored Dec 28, 2010 and Wolfgang Denk committed Jan 18, 2011

The lan91c96_detect_chip routine is not correct according
to the manual.
Signed-off-by: YanJun Yang <yangyj.ee@gmail.com>

Heiko Schocher authored Jan 12, 2011 and Wolfgang Denk committed Jan 18, 2011

Signed-off-by: Heiko Schocher <hs@denx.de>

The default value of the SRS, VS18 and VS30 and ADMAS fields in the host
controller capabilities register (HOSTCAPBLT) are incorrect. The default
of these bits should be zero instead of one.

Clear these bits out when we read HOSTCAPBLT.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Do not issue a manual asynchronous CMD12. Instead, use a (software)
synchronous CMD12 or AUTOCMD12 to abort data transfer.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

This change does the following:
- Adds printing of negotiated link width.  This information can be
  useful when debugging PCIe issues.
- Makes it optional for boards to implement board_serdes_name().
  Previously boards that did not implement it would print unsightly
  output such as "PCIE1: Connected to <NULL>..."
- Rewords the PCIe boot output to reduce line length and to make it
  clear that the "base address XYZ" value refers to the base address of
  the internal processor PCIe registers and not a standard PCI BAR
  value.
- Changes "PCIE" output to the standard "PCIe"

Before change:
PCIE1: connected to <NULL> as Root Complex (base addr ef008000)
  01:00.0     - 10b5:8518 - Bridge device
   02:01.0    - 10b5:8518 - Bridge device
   02:02.0    - 10b5:8518 - Bridge device
   02:03.0    - 10b5:8518 - Bridge device
PCIE1: Bus 00 - 05
PCIE2: connected to <NULL> as Endpoint (base addr ef009000)
PCIE2: Bus 06 - 06

After change:
PCIe1: Root Complex of PEX8518 Switch, x4, regs @ 0xef008000
  01:00.0     - 10b5:8518 - Bridge device
   02:01.0    - 10b5:8518 - Bridge device
   02:02.0    - 10b5:8518 - Bridge device
   02:03.0    - 10b5:8518 - Bridge device
PCIe1: Bus 00 - 05
PCIe2: Endpoint of VPX Fabric A, x2, regs @ 0xef009000
PCIe2: Bus 06 - 06
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Since all the PCIe controllers are connected over SERDES on the SoCs we
can utilize is_serdes_configured() to determine if a controller is
enabled.  After which we can setup the ATMUs and LAWs for the controller
in a common fashion and allow board code to specify what the controller
is connected to for reporting reasons.

We also provide a per controller (rather than all) for some systems that
may have special requirements.

Finally, we refactor the code used by the P1022DS to utilize the new
generic code.

Based on patch by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Previously we passed in a specifically named struct pci_controller to
determine if we had setup the particular PCI bus.  Now we can search for
the struct so we dont have to depend on the name or the struct being
statically allocated.

Introduced new find_hose_by_cfg_addr() to get back a pci_controller struct
back by searching for it means we can do things like dynamically allocate
them or not have to expose the static structures to all users.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>

Some new platform's esdhc pins don't share with other function.
The eSDHC shouldn't be disabled, even if "esdhc" isn't defined
in hwconfig env variable.

Use CONFIG_FSL_ESDHC_PIN_MUX to fix this problem.
Signed-off-by: Chenhui Zhao <b26998@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

This patch sync with David's patch on Linux for handling nand_scan_ident.

	commit 5e81e88a4c140586d9212999cea683bcd66a15c6
	Author: David Woodhouse <David.Woodhouse@intel.com>
	Date:   Fri Feb 26 18:32:56 2010 +0000

	mtd: nand: Allow caller to pass alternative ID table to nand_scan_ident()
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Lei Wen <leiwen@marvell.com>

This patch add addition suffix to nand write to give the uboot
the power to directly burn the yaffs image to nand.
Signed-off-by: Lei Wen <leiwen@marvell.com>

The variable i has to be static, otherwise it would be always zero.
Signed-off-by: Alexander Holler <holler@ahsoftware.de>

David Müller authored Dec 21, 2010 and Stefan Roese committed Jan 11, 2011

Signed-off-by: David Mueller <d.mueller@elsoft.ch>
Signed-off-by: Stefan Roese <sr@denx.de>

Yanjun Yang authored Dec 26, 2010 and Wolfgang Denk committed Jan 10, 2011

The eth_device.name field length is limited by NAMESIZE,
which is 16 defined in include/net.h. Unfortunately, two
of the names in lan91c96.c are beyond that.
Signed-off-by: YanJun Yang <yangyj.ee@gmail.com>

Chris Packham authored Dec 19, 2010 and Heiko Schocher committed Jan 10, 2011

This adds support for for the PCA9535/PCA9539 family of gpio devices which
have 16 output pins.

To let the driver know which devices are 16-pin it is necessary to define
CONFIG_SYS_I2C_PCA953X_WIDTH in your board config file. This is used to
create an array of {chip, ngpio} tuples that are used to determine the
width of a particular chip. For backwards compatibility it is assumed that
any chip not defined in CONFIG_SYS_I2C_PCA953X_WIDTH has 8 pins.
Acked-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>

Macpaul Lin authored Dec 21, 2010 and Wolfgang Denk committed Jan 09, 2011

Add Faraday's ftgmac100 (gigabit ethernet)
MAC controller's driver.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>

Mike Frysinger authored Dec 23, 2010 and Wolfgang Denk committed Jan 09, 2011

The include/miiphy.h header duplicates a lot of things from linux/mii.h.
So punt all the things that overlap to keep the API simple and to make
merging between U-Boot and Linux simpler.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Mike Frysinger authored Dec 22, 2010 and Wolfgang Denk committed Jan 09, 2011

The flash_verbose logic is only used by the CFI MTD layer, so if we aren't
using that, disable the logic completely.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The serial of ap325rxa has it of two kinds, and the setting of
the clock is different.
Because there was a problem by function to judge serial kind,
this revised it.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>

I copied the setting of CPU from Linux kernel and commonized it.
By this, we can communalize a kernel and information.
And added the serial setting of many CPU's.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

John Rigby authored Dec 20, 2010 and Wolfgang Denk committed Dec 21, 2010

It can be optimised out by the compiler otherwise resulting
in obscure errors like a board not booting.

This has been documented in README since 2006 when these were
first fixed up for GCC 4.x.
Signed-off-by: John Rigby <john.rigby@linaro.org>

Fix some additional places.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-By: Albert ARIBAUD <albert.aribaud@free.fr>

Li Yang authored Nov 25, 2010 and Wolfgang Denk committed Dec 18, 2010

The current code use all the voltage range support by the host
controller to do the validation.  This will cause problem when
the host supports Low Voltage Range.  Change the validation
voltage to be based on board setup.
Signed-off-by: Li Yang <leoli@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Jerry Huang authored Nov 25, 2010 and Wolfgang Denk committed Dec 18, 2010

The max clock of MMC is 52MHz
Signed-off-by: Jerry Huang <Changm-Ming.Huang@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Jerry Huang authored Nov 25, 2010 and Wolfgang Denk committed Dec 18, 2010

After booting the u-boot, and first using some SD card (such as Sandisk 2G SD
card), because the field 'clock' of struct mmc is zero, this will cause
the read transfer is always active and SDHC DATA line is always active,
therefore, driver can't handle the next command.

Therefore, we use mmc_set_clock to setup both the data structure and HW
to the initial clock speed of 400000Hz.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Li Yang authored Nov 25, 2010 and Wolfgang Denk committed Dec 18, 2010

The current code use all the voltage range support by the host
controller to do the validation.  This will cause problem when
the host supports Low Voltage Range.  Change the validation
voltage to be based on board setup.
Signed-off-by: Li Yang <leoli@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Jerry Huang authored Nov 25, 2010 and Wolfgang Denk committed Dec 18, 2010

The max clock of MMC is 52MHz
Signed-off-by: Jerry Huang <Changm-Ming.Huang@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Jerry Huang authored Nov 25, 2010 and Wolfgang Denk committed Dec 18, 2010

After booting the u-boot, and first using some SD card (such as Sandisk 2G SD
card), because the field 'clock' of struct mmc is zero, this will cause
the read transfer is always active and SDHC DATA line is always active,
therefore, driver can't handle the next command.

Therefore, we use mmc_set_clock to setup both the data structure and HW
to the initial clock speed of 400000Hz.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

This is part of the timer cleanup effort.
In the future we only use get_timer() in its intended way to
program timeout loops.
reset_timer() shall not be used anymore.
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>

These id tables need not be writable.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>