Pull request for efi-2022-04-rc5-2

Documentation:

* man-page for the wdt command

UEFI:

* Unit test for boot manager

When calling efi_dp_from_name() we are not interested in the device part.
Just pass NULL as an argument.

Suggested-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>

Provide a unit test for

* efidebug boot add
* efidebug boot order
* bootefi bootmgr
* initrd via EFI_LOAD_FILE2_PROTOCOL

Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>

Up to now the initrddump.efi application has drained the input after
showing the prompt. This works for humans but leads to problems when
automating testing. If the input is drained, this should be done before
showing the prompt.

Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>

initrddump.efi uses colored output and clear the screen. This is not
helpful for integration into Python tests. Allow specifying 'nocolor' in
the load option data to suppress color output and clearing the screen.

Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>

%s/devie-path/device-path/

Reported-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>

Describe the wdt command.

Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>

- Fix A20 GBit Ethernet operation
- Update board .dts files to provide correct RGMII PHY mode

Commit f11513d9 ("net: phy: realtek: Add tx/rx delay config for
8211e") made the Realtek PHY driver honour the phy-mode DT property,
to set up the proper delay scheme for the RX and TX lines. A similar
change in the kernel revealed that those properties were mostly wrong.
The kernel DTs got updated over the last few months, but we were missing
out on the U-Boot version.

Just sync in the phy-mode properties from the mainline kernel,
v5.17-rc7, to avoid the breaking DT sync that late in the cycle.

This fixes Ethernet operation on the affected boards.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>

Commit 5bc4cd05 ("sunxi: move non-essential code out of s_init()")
moved the call to eth_init_board() from s_init() into board_init_f().
This means it's now only called from the SPL, which makes sense for
most of the other moved low-level functions. However the GMAC pinmux and
clock setup in eth_init_board() was not happy about that, so it broke
the sun7i GMAC.

Since Ethernet is of no use in the SPL anyway, just move the call into
board_init(), which is only run in U-Boot proper.

This fixes Ethernet operation for the A20 SoCs, which broke in
v2022.04-rc1, with the above mentioned commit.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Tested-by: Petr Štetiar <ynezz@true.cz> [a20-olinuxino-lime2]

Heinrich Schuchardt authored 2 years ago and Tom Rini committed 2 years ago

Pin all dependencies as reported by 'pip freeze'.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

- a37xx: espressobin: Fix non-working SPI (Pali)

This contributor prefers not to receive mails authored 2 years ago and Stefan Roese committed 2 years ago

Commit 0934dddc ("arm: a37xx: Update DTS files to version from
upstream Linux kernel") ported Linux's device-tree files for Armada 3720
SOCs. This broke SPI support on some Espressobin boards and results in
following U-Boot error:

  Loading Environment from SPIFlash... jedec_spi_nor flash@0: unrecognized JEDEC id bytes: f7, 30, 0b
  *** Warning - spi_flash_probe_bus_cs() failed, using default environment

Before that commit DT node for SPI was called 'spi-flash@0' and after
that commit it is called 'flash@0'. Before that commit 'spi-max-frequency'
was set to 50000000 and after it is 104000000.

Rename DT node 'spi-flash@0 in armada-3720-espressobin-u-boot.dtsi to
'flash@0' and set custom U-Boot 'spi-max-frequency' back to 50000000.

With this change SPI is working on Espressobin again and it is detected
with JEDEC ids ef, 60, 16 on our tested unit.

  Loading Environment from SPIFlash... SF: Detected w25q32dw with page size 256 Bytes, erase size 4 KiB, total 4 MiB
  OK

Note that it is unknown why spi-max-frequency with value 104000000 does not
work in U-Boot as it works fine with Linux kernel. Also note that in
defconfig file configs/mvebu_espressobin-88f3720_defconfig is set option
CONFIG_SF_DEFAULT_SPEED=40000000 which is different value than in DT.

Fixes: 0934dddc ("arm: a37xx: Update DTS files to version from upstream Linux kernel")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>

i2c changes for fixes-for-2022.04

- atsha204a-i2c.c
  DTS and I2C fixes for Atmel ATSHA204 from Adrian

- i2c: fix always-true condition in i2c_probe_chip()
  from Nikita

- eeprom: Do not rewrite EEPROM I2C bus with DM I2C enabled
  from Marek

- clarify bootcount documentation fix from Michael

Marek Behún authored 2 years ago and Tom Rini committed 2 years ago

Commit 0934dddc ("arm: a37xx: Update DTS files to version from
upstream Linux kernel") ported Linux's device-tree files for Armada 3720
SOCs. This broke USB port on Turris MOX, because in Linux' DTS the bus
voltage supply is described as a `phy-supply` property of connector
node, a mechanism that is not supported in U-Boot yet.

For now, fix this by adding `vbus-supply` to usb3 node.

Fixes: 0934dddc ("arm: a37xx: Update DTS files to version from upstream Linux kernel")
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>

Michael Opdenacker authored 3 years ago and Heiko Schocher committed 2 years ago

- Grammar fixes
- Clarify explanations

Signed-off-by: Michael Opdenacker <michael.opdenacker@bootlin.com>
Reviewed-by: Heiko Schocher <hs@denx.de>

Marek Vasut authored 3 years ago and Heiko Schocher committed 2 years ago

With DM I2C, the EEPROM bus has been correctly configured in
eeprom_execute_command() already. Do not reconfigure it here
with hard-coded bus number again.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>

Nikita Yushchenko authored 3 years ago and Heiko Schocher committed 2 years ago

Per dm_i2c_ops.probe_chip documentation, i2c_probe_chip() shall fallback
to default probe method when .probe_chip() returns -ENOSYS.

Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Heiko Schocher <hs@denx.de>

Adrian Fiergolski authored 3 years ago and Heiko Schocher committed 2 years ago

This patch replaces use fdtdec_get_addr with simpler dev_read_addr().
fdtdec_get_addr doesn't work properly on ZynqMP-based (64bit) system. Although
not confirmed, it could be related to the fact, that quoting the documentation,
"This variant hard-codes the number of cells used to represent the address and
size based on sizeof(fdt_addr_t) and sizeof(fdt_size_t)".

Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>

Adrian Fiergolski authored 3 years ago and Heiko Schocher committed 2 years ago

Once request is sent, and before receiving a response, the delay is required.
This patch fixes missing delay for before first response try.

Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>

Adrian Fiergolski authored 3 years ago and Heiko Schocher committed 2 years ago

If the maximum number of wake-up attempts is exceeded, return -ETIMEDOUT.

Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>

Pull request for efi-2022-04-rc5

Documentation:

* Fix documentation of FIP creation for Amlogic boards
* Update Nokia RX-51 QEMU documentation
* Add Raspberry Pi documentation

UEFI:

* Fix booting via short form device paths
* Support short form device paths in 'efidebug boot add'
* Fix ESP detection for capsule updates
* Allow ACPI table usage even if device-tree exists - ignore DT
* OP-TEE based GetVariable(): return attributes when buffer too small

The tools dtbdump.efi and initrddump.efi are useful for Python testing even
if CONFIG_EFI_SELFTEST=n.

Don't clear the screen as it is incompatible with Python testing.

Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>

The block IO protocol may be installed on any handle. We should make
no assumption about the structure the handle points to.

efi_disk_is_system_part() makes an illegal widening cast from a handle
to a struct efi_disk_obj. Remove the function.

Fixes: Fixes: 41fd5068 ("efi_loader: disk: add efi_disk_is_system_part()")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>

The efi_system_partition_guid is needed in multiple places. Export it.

Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>

The GUID of partitions is sufficient for identification and will stay
constant in the lifetime of a boot option. The preceding path of the
device-path may change due to changes in the enumeration of devices.
Therefore it is preferable to use the short-form of device-paths in load
options. Adjust the 'efidebug boot add' command accordingly.

Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>

The boot manager must support loading from boot options using a short-form
device-path, e.g. one where the first element is a hard drive media path.

See '3.1.2 Load Options Processing' in UEFI specification version 2.9.

Fixes: 0e074d12 ("efi_loader: carve out efi_load_image_from_file()")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>

Let function efi_dp_find_obj() additionally check if a given protocol is
installed on the handle relating to the device-path.

Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>

efi_dp_find_obj() should not return any handle with a partially matching
device path but the handle with the maximum matching device path.

Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>

Rename function shorten_path() to efi_dp_shorten() and export it.

Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>

Ilias Apalodimas authored 2 years ago and Heinrich Schuchardt committed 2 years ago

Starting UEFI Spec 2.8 we must fill in the variable attributes when
GetVariable() returns EFI_BUFFER_TOO_SMALL and Attributes is non-NULL.

This code was written with 2.7 in mind so let's move the code around a
bit and fill in the attributes EFI_BUFFER_TOO_SMALL is returned

Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>

Alexander Graf authored 3 years ago and Heinrich Schuchardt committed 2 years ago

For targets that enable ACPI, we should not pass Device Trees into
the payload. However, our distro boot logic always passes the builtin
DT as an argument.

To make it easy to use ACPI with distro boot, let's just ignore the DT
argument to bootefi when ACPI is enabled. That way, we can successfully
distro boot payloads on ACPI enabled targets.

Signed-off-by: Alexander Graf <agraf@csgraf.de>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>

Matthias Brugger authored 3 years ago and Heinrich Schuchardt committed 2 years ago

Add documentation about the different configuration files for the
RaspberryPi board family.

Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>

Jan Kiszka authored 2 years ago and Heinrich Schuchardt committed 2 years ago

There is no CONFIG_UEFI_SECURE_BOOT, and there was never any.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>

This contributor prefers not to receive mails authored 3 years ago and Heinrich Schuchardt committed 2 years ago

Add section how to run U-Boot in n900 qemu machine.

Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>

Neil Armstrong authored 3 years ago and Heinrich Schuchardt committed 2 years ago

It add documentation on licencing & provides links to the amlogic-boot-fip
pre-built files collections.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

Neil Armstrong authored 3 years ago and Heinrich Schuchardt committed 2 years ago

The doc used GXL instructions, which couldn't work on GXBB SoCs.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

Johannes Krottmayer authored 3 years ago and Heinrich Schuchardt committed 2 years ago

Fix documentation path in deprecated warning message about device
driver.

Signed-off-by: Johannes Krottmayer <krjdev@gmail.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>

Johannes Krottmayer authored 3 years ago and Heinrich Schuchardt committed 2 years ago

Fix documentation path in warning message about deprecated device driver.

Signed-off-by: Johannes Krottmayer <krjdev@gmail.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>

- Fix for chromebook gru and bob board;
- some fix on driver like dram and saradc;