Added dt binding for seps525 display driver.

Signed-off-by: Vikhyat Goyal <vikhyat.goyal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Some drivers like LCD connected via SPI requires explicit sync function
which copy framebuffer content over SPI to controller to display.
This hook doesn't exist yet that's why introduce it via video operations.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

This patch is preparation for follow up one to support cases where
synchronization can fail.

Suggested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Place description below function parameters to make kernel-doc stript
happy. Also rename dev to vid to be aligned with function parameters.

Fixes: 1acafc73 ("dm: video: Add a video uclass")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Building xilinx_zynq_virt_defconfig fails on origin/next as reported by
GCC 10.2 (as provided by Debian Bullseye):

  CC      board/xilinx/common/fru_ops.o
board/xilinx/common/fru_ops.c: In function ‘fru_capture’:
board/xilinx/common/fru_ops.c:173:8:
error: array subscript 284 is outside array bounds of
‘struct fru_table[1]’ [-Werror=array-bounds]
  173 |  limit = data + sizeof(struct fru_board_data);
      |  ~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
board/xilinx/common/fru_ops.c:17:18: note: while referencing ‘fru_data’
   17 | struct fru_table fru_data __section(.data);
      |                  ^~~~~~~~

When using sizeof(struct fru_board_data) to find the end of the structure
you should add it to the start of the structure.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

This sort of code does not make much sense:

    if (ondie_ecc_enabled) {
        if (ondie_ecc_enabled) {

Remove the inner if.

The problem was indicated by cppcheck.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

This patch add ethernet node gem1 to zcu1285 RevB.
GMII to RGMII converter sits between MAC and external
phy connected over GMII to MAC and RGMMI to external phy

Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

This patch add ethernet node gem1 to zcu1275 RevB.
GMII to RGMII converter sits between MAC and external
phy connected over GMII to MAC and RGMMI to external phy.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

When unaligned 3 bytes data write operation is performed, 3rd byte
is being over written by 1st byte of 3 bytes data. This patch
fixes it.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Add parallel nor device to distroboot for microblaze.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Set script_offset_nor env variable using CONFIG_BOOT_SCRIPT_OFFSET
and nor flash start address to keep bootscript offset configurable.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

All changes are recorded in lore.kernel.org. Here are links to that patches
for the record.
Link: https://lore.kernel.org/r/f59a63d8cb941592de6d2dee8afa6f120b2e40c8.1601379794.git.michal.simek@xilinx.com
Link: https://lore.kernel.org/r/68f20a2b2bb0feee80bc3348619c2ee98aa69963.1598263539.git.michal.simek@xilinx.com
Link: https://lore.kernel.org/r/f767fe007e446a2299fda9905e75b723c650a424.1605021644.git.michal.simek@xilinx.com
Link: https://lore.kernel.org/r/cc294ae1a79ef845af6809ddb4049f0c0f5bb87a.1598259551.git.michal.simek@xilinx.com
Link: https://lore.kernel.org/r/20200629081744.13916-1-krzk@kernel.org



And there are other minor changes (just moving things around).

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Endianness detection is checked against uninitialized ret variable.
Assign ret with read value from status register to fix this.

Fixes: 31a359f8 ("serial: uartlite: Add support to work with any endianness")
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Reported by smatch like:
common/usb_storage.c:430 us_one_transfer() warn: inconsistent indenting

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Reported by smatch like:
cmd/load.c:228 read_record() warn: inconsistent indenting

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

The XPm_ConfigObject array definition generated by Vitis 2020.1 differs
from previous Vivado versions (before 2019.2).

-const u32 XPm_ConfigObject[] __attribute__((used, section(".sys_cfg_data"))) = {
+const u32 XPm_ConfigObject[] __attribute__((used, section(".sys_cfg_data"))) =
+#elif defined (__ICCARM__)
+#pragma location = ".sys_cfg_data"
+__root const u32 XPm_ConfigObject[] =
+#endif
+{

Change the matching regex to handle both cases.

Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Pull request for UEFI sub-system for efi-2021-01-rc5 (2)

The following errors in the UEFI sub-system are fixed:

* use after free in efi_exit()
* invalid free when using the boot manager
* pressing escape key once not recognized

Do not use data from the loaded image object after deleting it.

Fixes: 126a43f1 ("efi_loader: unload applications upon Exit()")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

Add the missing description of some fields of struct efi_loaded_image_obj.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

Add missing commas.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

load_options passed from do_efibootmgr() to do_bootefi_exec() may contain
invalid data from the stack which will lead to an invalid free().

Fixes: 0ad64007 ("efi_loader: set load options in boot manager")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

Up to now the escape key was not correctly detected in UEFI applications.
We had to hit it twice for a single escape to be recognized.

Use a 10 ms delay to detect if we are dealing with the escape key or an
escape sequence.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

IS_ENABLED() contains parentheses. But we should still put extra
parentheses around it in an if statement for readability.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

Fixes for 2021.1
----------------

CI: https://gitlab.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/5680

- fixes for Variscite dart6ul
- imx8mp : increase malloc area
- fixes for bx50v3
- imx8m: HS400ES and UHS for EVK
- imx8qm-rom7720: fix phy bind

- Fix "Assert PERST# signal when unloading driver" in a37xx PCI
  driver (Pali)
- Fix SPL on armada-xp-gp (add u-boot,dm-pre-reloc and alias) (myself)

This contributor prefers not to receive mails authored 4 years ago and Stefan Roese committed 4 years ago

This reverts commit 828d3262.

This change revers code which asserting PERST# signal when unloading
driver. Driver's remove callback is still there as it is used for other
functionality.

Asserting PERST# signal prior booting kernel is causing that A3720 boards
(Turris MOX and Espressobin) with stable Linux kernel versions 4.14 and
4.19 are not able to detect some PCIe cards (e.g. Compex WLE200 and WLE900)
and anymore. When PERST# signal is not asserted these cards are detected
correctly. As this is regression for existing stable Linux kernel versions
revert this problematic change in U-Boot.

To make cards working with OpenWRT 4.14 kernel it is needed to disable link
training prior booting kernel, which is already done in driver's remove
callback.

Described issue is in Linux kernel pci aardvark driver which is (hopefully)
fixed in latest upstream versions. Latest upstream versions should be able
to initialize PCIe bus and detects cards independently of the link training
and PERST# signal state.

So with this change, U-Boot on A3720 boards should be able to boot OpenWRT
4.14 kernel, stable 4.14 and 4.19 kernels and also latest mainline kernels.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>

For correct spi bus detection the spi0 alias is needed in the DT.
Otherwise this error will ocurr in U-Boot:

Invalid bus 0 (err=-19)
Failed to initialize SPI flash at 0:0 (error -19)

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Dennis Gilmore <dgilmore@redhat.com>
Tested-by: Dennis Gilmore <dgilmore@redhat.com>

Add some missing "u-boot,dm-pre-reloc;" properties to UART0, SPI
controller and SPI NOR flash node to enable usage in SPL. Otherwise
these devices will not be available.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Dennis Gilmore <dgilmore@redhat.com>
Tested-by: Dennis Gilmore <dgilmore@redhat.com>

Marc Ferland authored 4 years ago and Stefano Babic committed 4 years ago

Use 0x%2lx to print the i2c bus base address in hexadecimal format
instead of printing as an integer.

Signed-off-by: Marc Ferland <ferlandm@amotus.ca>
Reviewed-by: Fabio Estevam <festevam@gmail.com>

Heinrich Schuchardt authored 4 years ago and Stefano Babic committed 4 years ago

Use %u and not %d for unsigned values.
Print kHz and not khz.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>

Marc Ferland authored 4 years ago and Stefano Babic committed 4 years ago

The dart6ul has an i2c eeprom at 0x50 which contains, among other
things, the manufacturing/revision/options info of the SoM. This patch
replaces the current checkboard() implementation with a more
exhaustive one based on the content of the eeprom.

Since this code uses the new driver model, some changes were also
required in the DTS to make the nodes related to i2c available before
relocation.

This code was inspired from the supported u-boot code from Variscite
which can be found here:

https://github.com/varigit/uboot-imx/tree/imx_v2018.03_4.14.78_1.0.0_ga_var02



New output example:

Board: PN: VSM-6UL-705B, Assy: AS1812142257, Date: 2019 Feb 17
       Storage: eMMC, Wifi: yes, DDR: 1024 MiB, Rev: 2.4G

Signed-off-by: Marc Ferland <ferlandm@amotus.ca>
Reviewed-by: Fabio Estevam <festevam@gmail.com>

Marc Ferland authored 4 years ago and Stefano Babic committed 4 years ago

The eeprom at address 0x50 is a BR24G04NUX-3TTR. It has a
4Kbit (512x8) capacity, change the compatible string to reflect this
fact.

Also, add an alias to easily refer to this eeprom with
fdt_path_offset() which will be in another commit.

Signed-off-by: Marc Ferland <ferlandm@amotus.ca>
Reviewed-by: Fabio Estevam <festevam@gmail.com>

Igor Opaniuk authored 4 years ago and Stefano Babic committed 4 years ago

Hand over maintainership of Toradex SoMs (that I was responsible of) to
Oleksandr because of my resignation from Toradex, as such I will
have no immediate involvement with these modules and as a result not
able to continue maintaining these boards.

CC: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>

Fabio Estevam authored 4 years ago and Stefano Babic committed 4 years ago

When booting imx8mp-evk the following allocation error
message is seen:

U-Boot 2021.01-rc3-00200-ge668bec96a5f (Dec 21 2020 - 14:36:42 -0300)

alloc space exhausted

Fix it by increasing CONFIG_SYS_MALLOC_F_LEN to 0x10000 like it
is done on other i.MX8MM/8MN boards.

Reported-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>

Clément Péron authored 4 years ago and Stefano Babic committed 4 years ago

Calling ahab_close cmd force the user to interact for confirmation.

This is not user-friendly when using this cmd during factory process.

Allow the user to pass '-y' option to bypass this confirmation.

Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Oliver Graute <oliver.graute@kococonnector.com>

Sebastian Reichel authored 4 years ago and Stefano Babic committed 4 years ago

The current PHY rework does the following things:

1. Configure 125MHz clock
2. Setup the TX clock delay (RX is enabled by default),
3. Setup reserved bits to avoid voltage peak

The clock delays are nowadays already configured by the
PHY driver (in ar803x_delay_config). The code for that
can simply be dropped. The clock speed can also be
configured by the PHY driver by adding the device tree
property "qca,clk-out-frequency".

What is left is setting up the undocumented reserved bits
to avoid the voltage peak problem. I slightly improved its
documentation while updating the board's PHY rework code.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Sebastian Reichel authored 4 years ago and Stefano Babic committed 4 years ago

Instead of hardcoding index magic numbers in the board code,
also rely on board_fit_config_name_match choosing the right
config for the fitImage containing the kernel.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Pull request for UEFI sub-system for efi-2021-01-rc5

* In the Standalone MM based implementation of UEFI variables
  check the internal OP-TEE return code

Ilias Apalodimas authored 4 years ago and Heinrich Schuchardt committed 4 years ago

When opening an OP-TEE session we need to check the internal return
value of OP-TEE call arguments as well the return code of the
function itself.
The code was also ignoring to close the OP-TEE session in case the
shared memory registration failed.

Fixes: f042e47e ("efi_loader: Implement EFI variable handling via OP-TEE")
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

Sebastian Reichel authored 4 years ago and Stefano Babic committed 4 years ago

Add a host_build() function, so that it's possible to
check for software being build with USE_HOSTCC without
relying on preprocessor conditions. In other words

 #ifdef USE_HOSTCC
 	host_only_code();
 #endif

can be written like this instead:

 if (host_build())
 	host_only_code();

This improves code readability and test coverage and
compiler will eleminate this unreachable code.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>