Michael Walle authored 3 years ago and Priyanka Jain committed 3 years ago

Sometimes it is desireable to have the console output on the first
serial line. Introduce a configuration option for it (in the board
scope).

Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Michael Walle authored 4 years ago and Priyanka Jain committed 4 years ago

Although this variant has two external network ports, they are not (yet)
supported by the bootloader because they are connected via an internal
network switch. Otherwise its the same as the other variants.

Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Michael Walle authored 4 years ago and Priyanka Jain committed 4 years ago

This variant has one network port connected via RGMII and doesn't have
any TSN capabilities out-of-the-box. Instead it has all four SerDes
lanes available for customer use.

Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Michael Walle authored 4 years ago and Priyanka Jain committed 4 years ago

The variants differ in their network configuration. Move the first two
network aliases to the proper variant device tree includes. This is in
prepartion for variant 1 and 2 support which has a different network
port mapping. The network aliases for the two internal ports will stay
in the common dtsi because they are present on all board variants.

This might leave a hole if there is no ethernet1 alias. This is
intended.

Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Michael Walle authored 4 years ago and Tom Rini committed 4 years ago

Since linux commit 2e6cde96873253fd9eb0f20afd8ffd18278cff75 ("arm64:
dts: ls1028a: make the eMMC and SD card controllers use fixed indices")
mmc0 is the eMMC and mmc1 is the SD card. Also swap it in u-boot to
avoid any confusion by the user and to be aligned with linux.

Signed-off-by: Michael Walle <michael@walle.cc>

Michael Walle authored 4 years ago and Tom Rini committed 4 years ago

Add support to load the OP-TEE Trusted OS by the SPL.

Signed-off-by: Michael Walle <michael@walle.cc>

Michael Walle authored 4 years ago and Tom Rini committed 4 years ago

Add support to load the bl31 part of the ARM Trusted Firmware by the
SPL.

Signed-off-by: Michael Walle <michael@walle.cc>

Michael Walle authored 4 years ago and Tom Rini committed 4 years ago

It is not needed. Remove it.

Signed-off-by: Michael Walle <michael@walle.cc>

Michael Walle authored 4 years ago and Priyanka Jain committed 4 years ago

Add basic support for the Kontron SMARC-sAL28 board. This includes just
the bare minimum to be able to bring up the board and boot linux.

For now, the Single and Dual PHY variant is supported. Other variants
will fall back to the basic variant.

In particular, there is no watchdog support for now. This means that you
have to disable the default watchdog, otherwise you'll end up in the
recovery bootloader. See the board README for details.

Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>