- Oct 07, 2020
-
-
Increase CONFIG_SYS_BOOTM_LEN to 64MiB for Linux kernel booting. Signed-off-by:Stefan Roese <sr@denx.de>
-
Octeon needs a platform specific cmd to boot the Linux kernel, as specific parameters need to be passed and special handling for the multiple cores (SMP) is needed. Co-developed-by:
Aaron Williams <awilliams@marvell.com> Signed-off-by:
Daniel Schwierzeck <daniel.schwierzeck@gmail.com> -
This is needed for Linux booting, as the memory infos need to be passed in this bootmem format to the Linux kernel. Signed-off-by:
-
This patch adds the coremask handling functions. Signed-off-by:
-
Add header to handle bootinfo support, needed for Octeon Linux kernel booting. Signed-off-by:
-
Add header to handle Octeon fuse access. Signed-off-by:
-
This header includes the Octeon feature detection used in many Octeon drivers. Signed-off-by:
-
This header includes common register defines and accessor functions. Signed-off-by:
-
This patch adds the necessary lowlevel init code, to enable SMP Linux booting. This code will be used with the platform specific Octeon Linux boot command "bootoctlinux", which starts a configurable number of cores into Linux. Additionally some erratas and lowlevel register initializations are copied from the original Cavium / Marvell U-Boot source code, enabling booting into the Linux kernel. Signed-off-by: -
Add the #ifdef __ASSEMBLY__ checks to enable inclusion of this header from assembler files. Signed-off-by: -
This patch enables USB support with some helpful commands, like fs support. Signed-off-by: -
Add the USB device tree nodes to the Octeon dts/dtsi files. Signed-off-by:
Bin Meng <bmeng.cn@gmail.com> -
As noticed while working on the USB xHCI support, Octeon needs to flush all pending writes so that the values are present in the memory. Add this "syncw" instruction (twice) to flush_dcache_range(). Signed-off-by: -
Import platform specific mangle-port.h header, allowing a area specific swapping, which is needed on Octeon for USB & PCI areas. Imported from Linux v5.7. Signed-off-by: -
Import octeon_should_swizzle_table[] which is needed for the area specific swapping. It will be used by the platform specific mangle-port.h header. Imported from Linux v5.7. Signed-off-by: -
This patch adds the glue layer for the MIPS Octeon SoCs. It's ported mainly from the Linux code. Signed-off-by:
Bin Meng <bmeng.cn@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de> -
Octeon uses mapped addresses for virtual and physical memory. It's not that easy to calculate the resulting addresses here. So let's remove this BUG_ON() completely, as it's not really helpful. Please also note, that BUG_ON() is not recommended any more in the Linux kernel. Signed-off-by:
Bin Meng <bmeng.cn@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de> -
On MIPS platforms, mapping of the base address is needed. This patch switches from dev_get_addr() to dev_remap_addr() to get the mapped base address of the xHCI controller. Signed-off-by:
Bin Meng <bmeng.cn@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de> -
This patch adds the board specific configuration (struct) for the Octeon 3 EBB7304 EVK. This struct is ported from the 2013er Cavium / Marvell U-Boot repository. Also, the Octeon RAM driver is enabled in the board defconfig for its usage. Tested with one and two DIMMs on the EBB7304 EVK (8 & 16 GiB). Signed-off-by: -
This patch adds the initialization call for the Octeon RAM driver to the Octeon platforms code. So if enabled via Kconfig, the DDR driver will be called and the RAM will be configured and used. If the RAM driver is not enabled, the L2 cache is still used as RAM. Signed-off-by: -
This Octeon 3 DDR driver is ported from the 2013 Cavium / Marvell U-Boot repository. It currently supports DDR4 on Octeon 3. It can be later extended to support also DDR3 and Octeon 2 platforms. Part 3 includes the DIMM SPD handling code and the Kconfig / Makefile integration. Signed-off-by:
-
This Octeon 3 DDR driver is ported from the 2013 Cavium / Marvell U-Boot repository. It currently supports DDR4 on Octeon 3. It can be later extended to support also DDR3 and Octeon 2 platforms. Part 2 includes the very complex Octeon 3 DDR4 configuration Signed-off-by:
-
This Octeon 3 DDR driver is ported from the 2013 Cavium / Marvell U-Boot repository. It currently supports DDR4 on Octeon 3. It can be later extended to support also DDR3 and Octeon 2 platforms. Part 1 adds the base U-Boot RAM driver, which will be instantiated by the DT based probing. Signed-off-by:
-
This header will be used by the DDR driver (lmc). Its ported from the 2013 Cavium / Marvell U-Boot repository. Signed-off-by:
-
This header will be used by the DDR driver (lmc). Its ported from the 2013 Cavium / Marvell U-Boot repository. Signed-off-by:
-
This header is used by the upcoming DDR driver and potentially by other drivers ported from the 2013 Cavium / Marvell U-Boot repository. Signed-off-by:
-
This patch adds the memory controller (LMC) DT node to the Octeon 3 dtsi file. It also adds the L2C DT node, as this is referenced by the DDR driver. Signed-off-by:
-
- Oct 06, 2020
-
-
https://gitlab.denx.de/u-boot/custodians/u-boot-efiTom Rini authored
Pull request for UEFI sub-system for efi-2021-01-rc1 The following bugs in the UEFI system are resolved: * illegal free in EFI_LOAD_FILE2_PROTOCOL implementation * incorrect documentation of EFI_LOAD_FILE2_PROTOCOL implementation * output of CRC32 as decimal instead hexadecimal in unit test * use EfiReservedMemoryType for no-map reserved memory * avoid unnecessary resets in UEFI unit tests * call EFI bootmgr even without having /EFI/boot
-
https://gitlab.denx.de/u-boot/custodians/u-boot-amlogicTom Rini authored
- generate unique mac address from SoC serial on S400 board - Add USB support for GXL and AXG SoCs - Update Gadget code to use the new GXL and AXG USB glue driver - Add a VIM3 board support to add dynamic PCIe enable in OS DT - Fix AXG pinmux with requesting GPIOs - Add missing GPIOA_18 for AXG pinctrl - Add Amlogic PWM driver
-
Heinrich Schuchardt authored
The device tree may contain a /reserved-memory node. The no-map property of the sub-nodes signals if the memory may be accessed by the UEFI payload or not. In the EBBR specification (https://github.com/arm-software/ebbr ) the modeling of the reserved memory has been clarified. If a reserved memory node in the device tree has the no-map property map, create a EfiReservedMemoryType memory map entry else use EfiBootServicesData. Signed-off-by:
Heinrich Schuchardt <xypron.glpk@gmx.de>
-
Heinrich Schuchardt authored
CONFIG_EFI_GRUB_ARM32 is only needed for architectures with caches that are not managed via CP15 (or for some outdated buggy versions of GRUB). It makes more sense to disable the setting per architecture than per defconfig. Move QEMU's CONFIG_EFI_GRUB_ARM32_WORKAROUND=n from defconfig to Kconfig. Signed-off-by: -
There is an extra space. Signed-off-by:
Sean Anderson <seanga2@gmail.com> Reviewed-by:
-
Currently, the EFI bootmgr is only called if there is a EFI binary inside the path for removable media is found, i.e. /EFI/boot/. This doesn't make sense. It is the duty of the bootmgr to find out the path and name of the EFI binary to boot. It should be called even if there is no /EFI/boot directory. Thus, call the bootmgr before we try to boot the EFI binary inside the removable media path. Also remove the ${fdtcontroladdr} parameter because the fallback is handled in cmd/bootefi.c and that already takes care of correct settings if the board has ACPI and thus no device tree at all. Signed-off-by:Michael Walle <michael@walle.cc> Reviewed-by:
-
Heinrich Schuchardt authored
When we do not execute a test requiring ExitBootServices do not reset the system after testing. Signed-off-by: -
Heinrich Schuchardt authored
Print the CRC32 loaded via the EFI_LOAD_FILE2_PROTOCOL as a hexadecimal number. Signed-off-by:
Ilias Apalodimas <ilias.apalodimas@linaro.org>
-
Heinrich Schuchardt authored
Add code to use %x in efi_st_print(). Signed-off-by: -
Heinrich Schuchardt authored
strsep() changes the address that its first argument points to. We cannot use the changed address as argument of free(). Signed-off-by:
-
Heinrich Schuchardt authored
U-Boot offers a EFI_LOAD_FILE2_PROTOCOL which the Linux EFI stub can use to load an initial RAM disk. Update the function comments of the implementation. Signed-off-by:
-
- Oct 05, 2020
-
-
Tom Rini authored
Rsync all defconfig files using moveconfig.py Signed-off-by:Tom Rini <trini@konsulko.com>
-
Tom Rini authored
Bring in the assorted changes that have been staged in the 'next' branch prior to release. Signed-off-by:
-
