- May 10, 2024
-
-
J7200 has SR1.0 and SR2.0 having three variants of each GP, HS-FS and HS-SE. Current build does not generate HS-SE SR1.0 and HS-FS SR1.0 so add support for them. Reported-by:
Suman Anna <s-anna@ti.com> Reported-by:
Aniket Limaye <a-limaye@ti.com> Signed-off-by:
Neha Malcom Francis <n-francis@ti.com> Reviewed-by:
Andrew Davis <afd@ti.com>
-
J721E has SR1.1 and SR2.0 having three variants of each GP, HS-FS and HS-SE. Current build does not generate HS-FS SR1.1 so add support for them. Reported-by:
-
- Apr 26, 2024
-
-
-
https://source.denx.de/u-boot/custodians/u-boot-rockchipTom Rini authored
Please pull the updates for rockchip platform: - dts sync for rk3308; - sdram: Support getting banks from TPL for rk3568 and rk3588; - dts and config clean and sync up for rk3568/rk3588; - Other misc fixes; CI: https://source.denx.de/u-boot/custodians/u-boot-rockchip/-/pipelines/20543
-
https://source.denx.de/u-boot/custodians/u-boot-tpmTom Rini authored
Minor changes on this PR. Igor added some orphaned OP-TEE related files on the proper section of MAINTAINERS and fixed a potential buffer overflow in tee-sandbox
-
RK356x-based devices now support creating DRAM banks with proper holes by reading the ATAGS from Rockchip TPL blob, so let's use that mechanism instead. The CONFIG_NR_DRAM_BANK now defaults to 10 which is a safe bet for reading banks from ATAGS, so let's use the default value instead. Co-developed-by:
Chris Morgan <macromorgan@hotmail.com> Signed-off-by:
Quentin Schulz <quentin.schulz@theobroma-systems.com> Reviewed-by:
Kever Yang <kever.yang@rock-chips.com>
-
RK3588-based devices now support creating DRAM banks with proper holes by reading the ATAGS from Rockchip TPL blob, so let's use that mechanism instead. The CONFIG_NR_DRAM_BANK now defaults to 10 which is a safe bet for reading banks from ATAGS, so let's use the default value instead. Co-developed-by:
-
RK3588-based devices now support creating DRAM banks with proper holes by reading the ATAGS from Rockchip TPL blob, so let's use that mechanism instead. Since ft_board_setup isn't defined anymore, there's no need for selecting CONFIG_OF_BOARD_SETUP. Similarly, because the turing-rk1-rk3588.c would be empty, it is simply removed, with the (would-be-empty) Makefile as well. The CONFIG_NR_DRAM_BANK now defaults to 10 which is a safe bet for reading banks from ATAGS, so let's use the default value instead. Co-developed-by:
-
RK3588-based devices now support creating DRAM banks with proper holes by reading the ATAGS from Rockchip TPL blob, so let's use that mechanism instead. Since ft_board_setup isn't defined anymore, there's no need for selecting CONFIG_OF_BOARD_SETUP. Similarly, because the toybrick_rk3588.c would be empty, it is simply removed, with the (would-be-empty) Makefile as well. The CONFIG_NR_DRAM_BANK now defaults to 10 which is a safe bet for reading banks from ATAGS, so let's use the default value instead. Co-developed-by:
-
RK3588-based devices now support creating DRAM banks with proper holes by reading the ATAGS from Rockchip TPL blob, so let's use that mechanism instead. Since ft_board_setup isn't defined anymore, there's no need for selecting CONFIG_OF_BOARD_SETUP. Similarly, because the evb_rk3588.c would be empty, it is simply removed, with the (would-be-empty) Makefile as well. The CONFIG_NR_DRAM_BANK now defaults to 10 which is a safe bet for reading banks from ATAGS, so let's use the default value instead. All defconfigs using the CONFIG_TARGET_EVB_RK3588 are updated at once since they are impacted by this change. Co-developed-by:
-
RK3588-based devices now support creating DRAM banks with proper holes by reading the ATAGS from Rockchip TPL blob, so let's use that mechanism instead. Since ft_board_setup isn't defined anymore, there's no need for selecting CONFIG_OF_BOARD_SETUP. Similarly, because the rock5b-rk3588.c would be empty, it is simply removed, with the (would-be-empty) Makefile as well. The CONFIG_NR_DRAM_BANK now defaults to 10 which is a safe bet for reading banks from ATAGS, so let's use the default value instead. Co-developed-by:
-
RK3588-based devices now support creating DRAM banks with proper holes by reading the ATAGS from Rockchip TPL blob, so let's use that mechanism instead. Since ft_board_setup isn't defined anymore, there's no need for selecting CONFIG_OF_BOARD_SETUP. Similarly, because the rock5a-rk3588s.c would be empty, it is simply removed, with the (would-be-empty) Makefile as well. The CONFIG_NR_DRAM_BANK now defaults to 10 which is a safe bet for reading banks from ATAGS, so let's use the default value instead. Co-developed-by:
-
RK3588-based devices now support creating DRAM banks with proper holes by reading the ATAGS from Rockchip TPL blob, so let's use that mechanism instead. Since ft_board_setup isn't defined anymore, there's no need for selecting CONFIG_OF_BOARD_SETUP. Similarly, because the quartzpro64-rk3588.c would be empty, it is simply removed, with the (would-be-empty) Makefile as well. The CONFIG_NR_DRAM_BANK now defaults to 10 which is a safe bet for reading banks from ATAGS, so let's use the default value instead. Co-developed-by:
-
RK3588-based devices now support creating DRAM banks with proper holes by reading the ATAGS from Rockchip TPL blob, so let's use that mechanism instead. Since ft_board_setup isn't defined anymore, there's no need for selecting CONFIG_OF_BOARD_SETUP. Similarly, because the nanopc-t6-rk3588.c would be empty, it is simply removed, with the (would-be-empty) Makefile as well. The CONFIG_NR_DRAM_BANK now defaults to 10 which is a safe bet for reading banks from ATAGS, so let's use the default value instead. Co-developed-by:
-
When Rockchip TPL blob is used, the memory areas that can be used for DRAM is gotten from ATAGS passed through the DRAM at a specific address. The DDR_MEM tag contains at most 10 areas, so we should default to 10 if Rockchip TPL blob is used. Note that it is technically possible we need more if one of those 10 areas overlaps with reserved memory area, forcing us to split it in two. But a default doesn't need to handle all cases, only most. Signed-off-by:
-
Allow RK3568 and RK3588 based boards to get the RAM bank configuration from the ROCKCHIP_TPL stage instead of the current logic. This fixes both an issue where 256MB of RAM is blocked for devices with >= 4GB of RAM and where memory holes need to be defined for devices with more than 16GB of RAM. In the event that neither SoC is used or the ROCKCHIP_TPL stage is not used, fall back to existing logic. The logic handles creating memory holes from reserved memory areas defined in mem_map data struct in SoC C files, but only if the DRAM area overlaps with one reserved memory area. Since mem_map data struct is used, it should be rather straightforward to add support for other SoCs if needed. The logic is taken from Rockchip's U-Boot tag linux-5.10-gen-rkr4.1 (e08e32143dd). Note that Rockchip's U-Boot/TF-A/OP-TEE modify the ATAGS at runtime as well, but the DDR_MEM tag seems to be pretty much stable (though BL31 seems to be reserving only 1MB for itself at the moment). u32 for ATAGS is used because it simplifies the pointer arithmetic and it's expected that ATAGS are always below the 4GB limit allowed by u32. Co-developed-by:
-
Some variants of the ROCK Pi 4 series have an SPI flash chip populated which can be booted from. This patch enables support in U-Boot for building the image for the SPI flash, support for booting U-Boot from the SPI flash chip and support in U-Boot for accessing the SPI flash using `sf` commands. Not all variants (e.g. ROCK Pi 4B, ROCK 4 Model C Plus, ROCK 4SE) come populated with an SPI flash chip, but have the footprint on the board so a user could solder their own to the board. With this patchset applied, these board variants without an SPI flash chip still boot from MMC. I have enabled support for both Winbond and XTX SPI flash devices since different hardware variants have different devices populated: - `rockpi4_v13_sch_20181112.pdf` contains a Winbond part `W25Q64FWZPIG` - `rockpi4_v14_sch_20210114.pdf` contains an XTX part `XT25F32BWOIGT` The ROCK Pi 4 I have is marked as "ROCK PI 4 v1.48" and contains an SPI flash chip from XTX: => sf probe SF: Detected xt25f32 with page size 256 Bytes, erase size 4 KiB, total 4 MiB In the interest of supporting all board variants and not regressing existing users who boot from MMC, I have enabled support for booting from both SPI flash chip variants in the defconfig and left the environment storage location as MMC to not break existing users who have the environment stored on MMC. Signed-off-by:Christopher Obbard <chris.obbard@collabora.com> Reviewed-by:
Jonas Karlman <jonas@kwiboo.se>
-
To prepare for ROCK Pi 4A SPI flash support, sync the DTS from Linux which includes an SPI flash node. Kernel tag: v6.6-rc1 Kernel commits: - eddf73029770 ("arm64: dts: rockchip: Enable internal SPI flash for ROCK \ Pi 4A/B/C") Reviewed-by: -
The vop node should not be included in TPL/SPL control FDT, it should only be included at U-Boot proper pre-reloc phase. Change to use bootph-some-ram prop to fix this. Fixes: 6794063d ("ARM: dts: rk3328: Enable VOP for bootph-all") Signed-off-by:
-
Port the RK3328 part of the Rockchip IO-domain driver from linux. This differs from linux version in that pmu io iodomain bit is enabled in the write ops instead of in an init ops as in linux, this way we can avoid keeping a full state of all supply that have been configured. Enable by default on all RK3328 boards, skip rk3328-evb because this target is typically also used on miscellaneous boards and boxes not fully supported by U-Boot. Signed-off-by:
-
The RK3328 SoC support ARMv8 Cryptography Extensions and use of the ARMv8 crypto extensions help speed up FIT checksum validation in SPL. Imply ARMV8_SET_SMPEN and ARMV8_CRYPTO to take advantage of the crypto extensions for SHA256 when validating checksum of FIT images. Also imply OF_LIVE to help speed up init of U-Boot proper. Signed-off-by:
-
Sort imply statements under ROCKCHIP_RK3328 alphabetically and remove ENABLE_ARM_SOC_BOOT0_HOOK, DEBUG_UART_BOARD_INIT and SYS_NS16550, they are already implyed or selected by ARCH_ROCKCHIP. Signed-off-by:
-
Use a wildcard to simplify the list of board DT files in the MAINTAINERS file for the Radxa Rock 2 Square board. Signed-off-by:
Dragan Simic <dsimic@manjaro.org> Reviewed-by:
-
Display TPL init information message only when TPL_BANNER_PRINT configuration entry is set. This allows to disable information message in case logs on UART are unwanted. Update parent ifdef condition to check also CONFIG_TPL_SERIAL to match logic of the non-PX30 TPL implementation. Signed-off-by:
Lukasz Czechowski <lukasz.czechowski@thaumatec.com> Reviewed-by:
-
The commit 2cc6cde6 ("mmc: rockchip_sdhci: Limit number of blocks read in a single command") introduced a limit of number of blocks to read to fix a Data End Bit Error on RK3568 and RK3588. This had a side affect of significant slowing down reading FIT from eMMC. After the commit 6de9d7b2 ("rockchip: rk35xx: Enable eMMC HS200 mode by default") the limit of number of blocks to read workaround is no longer necessary and at HS200+ a Data End Bit Error is no longer happening using PIO mode. Change this limitation to allow reading more than 4 blocks with a single CMD18 command in PIO mode at HS200+ speed, keep using the 4 blocks limitation when loadig FIT from eMMC at lower speed than HS200. Fixes: 2cc6cde6 ("mmc: rockchip_sdhci: Limit number of blocks read in a single command") Signed-off-by:
-
The generic RK35xx board targets are intended to be used as a bare minimum target that can be used to e.g. boot boards that mostly follow reference hw design before a board spefic target has been added or for flashing and recovery purposes. Disable BOOTMETH_VBE, NET and ADC as these features are not intended to ever be used by these minimal generic board targets. Enable SYSRESET_PSCI to let TF-A handle sysreset from U-Boot proper. Signed-off-by:
-
Add support for USB OTG, RockUSB and UMS to the generic RK3588S/RK3588 target. Signed-off-by:
-
The default pinctrl for UART2 is using M1 iomux, however, all other supported RK3588 boards in U-Boot use M0 iomux for UART2. Change to use the M0 pinctrl for UART2 to match other supported boards. Fixes: b54c3d0d ("rockchip: board: Add minimal generic RK3588S/RK3588 board") Signed-off-by:
-
Add support for USB OTG, RockUSB and UMS to the generic RK3566/RK3568 target. Signed-off-by:
-
Add support for booting from SPI flash using the generic RK3566/RK3568 target. Signed-off-by:
-
Add missing emmc_datastrobe and sdmmc0_det pinctrl to fix possible issue reading from eMMC or SD-card. Also use correct node for mmc1 alias. Fixes: 683f61a1 ("rockchip: board: Add minimal generic RK3566/RK3568 board") Fixes: 363cbd57 ("rockchip: rk3568-generic: Enable eMMC HS200 mode") Signed-off-by:
-
Enable SPL_FIT_SIGNATURE=y and LEGACY_IMAGE_FORMAT=y to validate FIT images checksum in SPL. Change to SPL_MAX_SIZE=0x40000 to allow SPL up to 256 KiB in size. Enable SPL_DM_SEQ_ALIAS=y and SPL_PINCTRL=y to ensure eMMC and SD-card pinctrl is configured in SPL. Enable SYS_NS16550_MEM32=y to use readl/writel in serial driver. Signed-off-by:
-
RK35xx boards are expected to use the dwc3-generic driver and not the xhci-dwc3 driver. Remove the USB_XHCI_DWC3 option to ensure that the dwc3-generic driver is used. Fixes: 153ac950 ("board: rockchip: Add the Turing RK1 SoM") Signed-off-by:
-
Add Rockchip Toybrick TB-RK3588X .dtb-file entry in Makefile. Fixes: 9fdd9a54 ("board: rockchip: add Rockchip Toybrick TB-RK3588X board") Signed-off-by:
-
Pinctrl must be configured for eMMC, SD-card and SPI flash to successfully read FIT from all possible fallback media in SPL. Include pinctrl props and enable the SPL_PINCTRL Kconfig option to ensure FIT can be loaded from eMMC, SD-card and SPI flash. Also enable the SPL_DM_SEQ_ALIAS Kconfig option to ensure that the storage device sequence number matches in both SPL and U-Boot proper. Fixes: 9fdd9a54 ("board: rockchip: add Rockchip Toybrick TB-RK3588X board") Signed-off-by:
-
Fix CoolPi 4 Model B and CoolPi CM5 EVB .dtb-file entries in Makefile. Fixes: 3e15dee3 ("board: rockchip: Add support for rk3588 based Cool Pi CM5 EVB") Signed-off-by:
-
Add the CoolPi 4 Model B and CoolPi CM5 EVB board to the documentation. Fixes: 3e15dee3 ("board: rockchip: Add support for rk3588 based Cool Pi CM5 EVB") Signed-off-by:
-
The SF_DEFAULT_SPEED Kconfig option got lost during merge and this prevent reading FIT from SPI flash. Restore the SF_DEFAULT_SPEED option to fix this. Fixes: 8a94c376 ("rockchip: Use common bss and stack addresses on RK356x") Signed-off-by:
-
Pinctrl must be configured for eMMC, SD-card and SPI flash to successfully read FIT from all possible fallback media in SPL. Include pinctrl props and enable the SPL_PINCTRL Kconfig option to ensure FIT can be loaded from eMMC, SD-card and SPI flash. Also enable the SPL_DM_SEQ_ALIAS Kconfig option to ensure that the storage device sequence number matches in both SPL and U-Boot proper. Signed-off-by:
-
Pinctrl must be configured for eMMC, SD-card and SPI flash to successfully read FIT from all possible fallback media in SPL. Include pinctrl props and enable the SPL_PINCTRL Kconfig option to ensure FIT can be loaded from eMMC, SD-card and SPI flash. Signed-off-by:
-
