This commit fixes the change of below commit
"spi: fsl_qspi: Use GENMASK"
(sha1 :bad490a2)

Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>

stm_is_locked_sr() takes the status register (SR) value as the last
parameter, not the second.

Based on a patch from Brian Norris for the linux kernel:
http://git.infradead.org/linux-mtd.git/commit/a32d5b726ff8cf32bf491522b0ac8ae2545a063e



Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>

since:
commit: f05ad9ba "Add a way to skip relocation"

tqm5200s board fails to boot. Reason is that
board_init_f has a function parameter bootflag,
which is not setup in
in arch/powerpc/cpu/mpc5xxx/start.S _start

So board_init_f gets a undefined bootflag,
currently the gd pointer address. Unfortunately
this address sets the GD_FLG_SKIP_RELOC bit,
so u-boot code gets not relocated and u-boot
does not boot ...

Init bootflag with 0, and tqm5200 boots fine again.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <yorksun@freescale.com>

Signed-off-by: Tom Rini <trini@konsulko.com>

Peng Fan authored 9 years ago and Tom Rini committed 9 years ago

Use snprintf to replace sprintf.

Coverity log:
"
Unbounded source buffer (STRING_SIZE)
string_size: Passing string init_val of unknown size to sprintf.
"

Reported-by: Coverity
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>

Peng Fan authored 9 years ago and Tom Rini committed 9 years ago

Before calling hsearch_r, initialize callback entry to NULL.

Coverity log:
"
Uninitialized scalar variable (UNINIT)
uninit_use_in_call: Using uninitialized value e.
Field e.callback is uninitialized when calling hsearch_r.
"

Reported-by: Coverity
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>

Peng Fan authored 9 years ago and Tom Rini committed 9 years ago

Whether CONFIG_SYS_HUSH_PARSER is defined or not, should always
check to free 'buff' to avoid memory leak.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>

Miao Yan authored 9 years ago and Tom Rini committed 9 years ago

In struct e1000_rx_desc, field 'length' is declared as
uint16_t, so use le16_to_cpu() to do endianness conversion.

Also drop conversion on 'status' which is declared as
uint8_t.

Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

Miao Yan authored 9 years ago and Tom Rini committed 9 years ago

In pci_map_region(), pass 'range_id' to fdt_read_range(),
otherwise the same address will be mapped again in other
calls to pci_map_region()

Signed-off-by: Miao Yan <yammiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alexander Graf <agraf@suse.de>

Heiko Schocher authored 9 years ago and Tom Rini committed 9 years ago

using checkpatch with Perl 5.22.0 generates a warning,
this is fixed in linux through commit:

commit 4e5d56bdf892e18832a6540b63ebf709966bce2a
Author: Eddie Kovsky <ewk@edkovsky.org>
Date:   Wed Sep 9 15:37:52 2015 -0700

checkpatch: fix left brace warning

Using checkpatch.pl with Perl 5.22.0 generates the following warning:

Unescaped left brace in regex is deprecated, passed through in regex;

This patch fixes the warnings by escaping occurrences of the left brace
inside the regular expression.

Adapt it for U-Boot.

Signed-off-by: Heiko Schocher <hs@denx.de>

Eric Nelson authored 9 years ago and Tom Rini committed 9 years ago

Table 41 of the JEDEC standard for eMMC says that bit 31 of
the command argument is obsolete when issuing the ERASE
command (CMD38) on page 115 of this document:
	http://www.jedec.org/sites/default/files/docs/jesd84-B45.pdf

The SD Card Association Physical Layer Simplified Specification also
makes no mention of the use of bit 31.
	https://www.sdcard.org/downloads/pls/part1_410.pdf



The Linux kernel distinguishes between secure (bit 31 set) and
non-secure erase, and this patch copies the macro names from
include/linux/mmc/core.h.

Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Eric Nelson <eric@nelint.com>
Tested-by: Hector Palacios <hector.palacios@digi.com>

Ladislav Michl authored 9 years ago and Heiko Schocher committed 9 years ago

drivers/mtd/ubi/io.c:1354:3: error: 'dump_len' undeclared (first use in
this function)
   dump_len = max_t(int, 128, len - i);

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>

Peng Fan authored 9 years ago and Stefano Babic committed 9 years ago

Move setup_display from board_early_init_f to board_init.
Add more clock settings.
Add blacklight iomux setting.
Add display_info_t info for the lvds screen.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>

Gong Qianyu authored 9 years ago and Stefano Babic committed 9 years ago

This could avoid executing the code that only applies to i.MX platforms.

The bus_i2c_init() is called before relocation and will assgin value
to a static variable. If U-Boot is then still running in a flash
device, it's theoretically not allowed to write data to flash without
an erasing operation. For i.MX platforms, the U-Boot is always running
in DDR.

Actually it causes asynchronous error when the ARM64 system error
report is enabled and the flash write protect is set.

Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: Heiko Schocher <hs@denx.de>

Check for bmode before reading the boot device
to check if a serial downloader is started,
and returns UART if the serial downloader is set,
letting SPL to wait for an image if
CONFIG_SPL_YMODEM_SUPPORT is set.

This allows to load again a SPL based board
with imx_usb_loader together with a tool
such as kermit.

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Fabio Estevam <Fabio.Estevam@freescale.com>
CC: Eric Nelson <eric.nelson@boundarydevices.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
Tested-by: Eric Nelson <eric@nelint.com>

Michael Heimpold authored 9 years ago and Stefano Babic committed 9 years ago

For some board designs, it might be useful to switch the DC-DC
clock source to something else rather the default 24 MHz, e.g.
for EMI reasons.

For this, override the mxs_power_setup_dcdc_clocksource function
in your board support files.

Example:
void mxs_power_setup_dcdc_clocksource(void)
{
    mxs_power_switch_dcdc_clocksource(POWER_MISC_FREQSEL_20MHZ);
}

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>

Michael Schanz authored 9 years ago and Stefano Babic committed 9 years ago

Use the macro SETUP_IOMUX_PAD(...) rather than imx_iomux_v3_setup_multiple_pads(...) in order to setup
the pin configuration for ECSPI1.

ARRAY_SIZE(pads) provides the wrong size for imx_iomux_v3_setup_multiple_pads(pads, ARRAY_SIZE(pads)) in
case of MX6QDL. In the particular case, the content of GPR12 is overwritten and the IPG/AHB/ATB/ATP clocks
are deactivated. Therefore, the connection to the system via JTAG is not possible anymore. Furthermore,
kernel version 3.0.35 hangs during bootprocess in the function etm_init().

Signed-off-by: Michael Schanz <michael.schanz@congatec.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>

Måns Rullgård authored 9 years ago and Stefano Babic committed 9 years ago

If fecmxc_initialize_multi() fails, it frees but does not unregister
the mdio bus, causing subsequent uses of the "mii" command to crash.
Fix this by adding mdio_unregister() calls where needed.

Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Eric Nelson <eric@nelint.com>

Måns Rullgård authored 9 years ago and Stefano Babic committed 9 years ago

If the host clock frequency is higher than 100 MHz, the MDIO hold
time needs to be increased from its current setting of one cycle in
order to meet the specified minium of 10 ns.  Writing an appropriate
value to the HOLDTIME field of the MII_SPEED register achieves this.

Comment copied from Linux kernel.

Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Eric Nelson <eric@nelint.com>

Maximilian Schwerin authored 9 years ago and Stefano Babic committed 9 years ago

This patch writes the default values for TXTL and RXTL to UARTx_UFCR.
Without this patch some older kernel versions crash as UARTx_UFCR was
not always correctly initialized.

Signed-off-by: Maximilian Schwerin <maximilian.schwerin@tigris.de>

Eric Nelson authored 9 years ago and Stefano Babic committed 9 years ago

The low four bits of the SYSCTL register are reserved on the USDHC
controller on i.MX6 and i.MX7 processors, but are used for clocking
operations on earlier models.

Guard against their usage by hiding the bit mask macros on those
processors.

These bits are used to prevent glitches when changing clocks on
i.MX35 et al. Use the RSTA bit instead for i.MX6 and i.MX7.

>From the i.MX6DQ RM:
	To prevent possible glitch on the card clock, clear the
	FRC_SDCLK_ON bit when changing clock divisor value(SDCLKFS
	or DVS in System Control Register) or setting RSTA bit.

Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Hector Palacios <hector.palacios@digi.com>

Peng Fan authored 9 years ago and Stefano Babic committed 9 years ago

Drop duplicated debug info for tcl.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>

Stefan Brüns authored 9 years ago and Marek Vasut committed 9 years ago

The ifdef'ed Linux kernel code uses the 1 based port number, whereas U-Boot
puts a 0 based port number into the register. The reason the 0 based port
number apparently works can probably be taken from the USB 2.0 spec:

8.4.2.2 Start-Split Transaction Token
... The host must correctly set the port field for single and multiple TT
hub implementations. A single TT hub implementation *may ignore* the port
field.

Actually, as far as I understand, a multi TT hub defaults to single TT
(bAlternateSetting: 0) until switched via SetInterface, so even "port 42"
would work.

The change was verified by hardcoding the port number to a wrong value,
SPLIT transactions kept working (although using a DWC2 instead of MUSB).
Tested hubs are the RPi onboard SMC9514 and an external "05e3:0608
Genesys Logic, Inc. USB-2.0 4-Port HUB". The former is a multi TT hub,
the latter single TT only.

Addendum: Tested on sunxi/MUSB by Hans de Goede

Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>

Stefan Brüns authored 9 years ago and Marek Vasut committed 9 years ago

Start split and complete split tokens need the hub address and the
downstream port of the first HS hub (device view).

The core of the function was duplicated in both host/ehci_hcd and
musb-new/usb-compat.h.

Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>

Stefan Brüns authored 9 years ago and Marek Vasut committed 9 years ago

flush_dcache_range may access data after priv->aligned_buffer end if
len > DWC2_DATA_BUF_SIZE.
memcpy may access data after buffer end if done > 0

Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>

Stefan Brüns authored 9 years ago and Marek Vasut committed 9 years ago

The configuration descriptor includes all interface, endpoint and
auxiliary descriptors (e.g. report, union) so 512 bytes may not be enough.

Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>

Allow ctrl-c to abort the erase ops.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>

Show sector erase progress with dot and comma.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>

Skip erase if the sector is blank. The sector erase is slow, and
may take 0.7 sec typically or up to 3 sec worst-case.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>

If the erase fails, fail_addr might indicate exactly which block
failed. If fail_addr = MTD_FAIL_ADDR_UNKNOWN, the failure was not
at the device level or was not specific to any particular block.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>

Erase is an asynchronous operation.  Device drivers are supposed
to call instr->callback() whenever the operation completes, even
if it completes with a failure.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>

There are some reports of stability issues at 672 MHz, see:
http://linux-sunxi.org/Orange_Pi_PC#DRAM_clock_speed_limit



So reduce the DRAM speed to 624MHz which seems to be reliable everywhere.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

Conflicts:
	include/configs/axs101.h

Signed-off-by: Tom Rini <trini@konsulko.com>

Chin Liang See authored 9 years ago and Marek Vasut committed 9 years ago

Updated pinmux group GENERALIO[15-16] for i2c.

Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: shengjiangwu <shengjiangwu@icloud.com>