Nicolas Saenz Julienne authored 3 years ago and Matthias Brugger committed 3 years ago

The @suse.de address doesn't exist anymore. Update it to something not
dependent on my workplace.

Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>

Signed-off-by: Tom Rini <trini@konsulko.com>

- turris_omnia: fix leaked mtd device (Marek)
- phy: marvell: cp110: Fix SATA invert polarity (Denis)

Denis Odintsov authored 3 years ago and Stefan Roese committed 3 years ago

In commit b24bb99d cp110 configuration initially done in u-boot
was removed and delegated to atf firmware as smc call.
That commit didn't account for later introduced in d13b740c SATA invert polarity support.

This patch adds support of passing SATA invert polarity flags to atf
firmware during the smc call.

Signed-off-by: Denis Odintsov <shiva@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>

Marek Behún authored 3 years ago and Stefan Roese committed 3 years ago

After getting MTD device via get_mtd_device_nm(), we need to put it with
put_mtd_device(), otherwise we get

  Removing MTD device #0 (mx25l6405d) with use count 1

before booting kernel.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Tested-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>

Pull request for efi-2021-10-rc5

Documentation:

* add /config bindings to HTML documentation

UEFI

* Fix number_of_algorithms field in TCG EFI Protocol

Ruchika Gupta authored 3 years ago and Heinrich Schuchardt committed 3 years ago

TCG EFI Protocol Specification defines the number_of_algorithms
field in spec ID event to be equal to the number of active
algorithms supported by the TPM device. In current implementation,
this field is populated with the count of all algorithms supported
by the TPM which leads to incorrect spec ID event creation.

Similarly, the algorithm array in spec ID event should be a variable
length array with length being equal to the number_of_algorithms field.
In current implementation this is defined as a fixed length array
which has been fixed.

Signed-off-by: Ruchika Gupta <ruchika.gupta@linaro.org>
CC: Masahisa Kojima <masahisa.kojima@linaro.org>
CC: Ilias Apalodimas <ilias.apalodimas@linaro.org>
CC: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>

Simon Glass authored 3 years ago and Heinrich Schuchardt committed 3 years ago

The devicetree binding files are in their own directory and use a simple
text format. Add a link for the binding for the /config node, since it
is otherwise hard to find.

Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

- Assorted bugfixes, MAINTAINER updates and dead code removal

Simon Guinot authored 3 years ago and Tom Rini committed 3 years ago

Since Albert Aribaud is not maintaining anymore the LaCie Ethernet Disk
mini V2 board, then I am taking over.

Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>

Patrick Delaunay authored 3 years ago and Tom Rini committed 3 years ago

Remove the driver st_smic.c used in SPEAr products and the associated
config CONFIG_ST_SMI; this driver is no more used in U-Boot after the
commit 570c3dcf ("arm: Remove spear600 boards and the rest of SPEAr
support").

Fixes: 570c3dcf ("arm: Remove spear600 boards and the rest of SPEAr support")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>

Martyn Welch authored 3 years ago and Tom Rini committed 3 years ago

I am taking over responsibility for the GE board from Sebastian Reichel.
Updating the MAINTAINERS files to reflect this.

Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Patrick Delaunay authored 3 years ago and Tom Rini committed 3 years ago

As the lastest spear directories are removed, delete the associated entry
in the MAINTAINERS file:
- arch/arm/cpu/arm926ejs/spear/
- arch/arm/include/asm/arch-spear/

Fixes: 570c3dcf ("arm: Remove spear600 boards and the rest of SPEAr support")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

Heinrich Schuchardt authored 3 years ago and Tom Rini committed 3 years ago

Output like the following is quite irritating:

    => bootefi hello
    Scanning disk mmc2.blk...
    No valid Btrfs found
    Bad magic number for SquashFS image.
    ** Unrecognized filesystem type **
    Scanning disk mmc1.blk...
    No valid Btrfs found
    Bad magic number for SquashFS image.
    ** Unrecognized filesystem type **
    Scanning disk mmc0.blk...
    No valid Btrfs found
    Bad magic number for SquashFS image.
    ** Unrecognized filesystem type **

Albeit a whole disk may be formatted with a filesystem in most cases
a partition table is used and the whole disk (partition number 0) doesn't
contain a filesytem. Some partitions may only contain a blob. Not seeing a
filesytem on the whole disk or on any partition is only worth a debug
message.

Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Heinrich Schuchardt authored 3 years ago and Tom Rini committed 3 years ago

Our mailmapper script required Python 2 which is no longer maintained.
A main difference when converting to Python 3 is that byte strings are not
character strings. So add conversion and skip over conversion errors.

Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>

T Karthik Reddy authored 3 years ago and Tom Rini committed 3 years ago

Tpm test cases relies on tpm device setup. Provide an environment
variable "env__tpm_device_test_skip = True" to skip the test case
if tpm device is not present.
Only needed will have to add variable to the py-test framework.
Test runs successfully even this variable is absent.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>

Bugfixes for this one socfpga platform

Late bunch of USB fixes (incl. the xhci usb 3.1 support)

The KBUILD_BASENAME contains just the name of the compiled module,
in this case 'sequencer', rather than a full path to the compiled
file. Use it to prevent pulling the full path into the U-Boot binary,
which is useless and annoying.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>

The DM DWMAC driver is perfectly capable of configuring the ethernet
PHY reset GPIO, let the driver do it instead of doing it in the board
file.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>

The Designware I2C IP is used to communicate with I2C peripherals on
SoCFPGA, and required to access I2C EEPROM on this board. Enable it.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>

The USB peripheral controller is the DWC2 controller 1, not 0.
Update the phandle to fix UDC support on this board.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>

The WDT on this system should be enabled, make it so.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>

The SPI NOR bus mode is 0 on this system, update it accordingly.
Increase frequency to 40 MHz and enable SFDP parsing, since the
flashes on this system support that and it is a huge performance
improvement.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>

This was configured in downstream, so it is likely that most of the
custom software used around the device depends on it. Make upstream
compatible.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>

Increase the environment size from 4k to 16k to prevent
environment from becoming full.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>

The comment is no longer meaningful due to DT conversion, drop it.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>

Mark Kettenis authored 3 years ago and Marek Vasut committed 3 years ago

This adds support for the DWC_sub31 controllers such as those
found on Apple's M1 SoC.  This version of the controller
seems to work fine with the existing driver.

Signed-off-by: Mark Kettenis <kettenis@openbsd.org>

Matthias Schiffer authored 3 years ago and Marek Vasut committed 3 years ago

Allow using different PHY interfaces for multiple USB controllers. When no
value is set in DT, we fall back to CONFIG_MXC_USB_PORTSC for now to stay
compatible with current board configurations.

This also adds support for the HSIC mode of the i.MX7.

Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>

Matthias Schiffer authored 3 years ago and Marek Vasut committed 3 years ago

These definitions are unused, all boards that define portsc flags use
the equivalent PORT_* definitions instead.

Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>

Matthias Schiffer authored 3 years ago and Marek Vasut committed 3 years ago

The MXC_EHCI_MODE_ definitions are redundant. Replace MXC_EHCI_MODE_SERIAL
with the equivalent PORT_PTS_SERIAL.

Only the zmx25 platform is affected.

Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>

Matthias Schiffer authored 3 years ago and Marek Vasut committed 3 years ago

Import usb_phy_interface enum values and DT match strings from the Linux
kernel.

Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>

Samuel Holland authored 3 years ago and Marek Vasut committed 3 years ago

Pine H64 and Orange Pi 3 both provide a USB3 type A port.
Enable it in U-Boot.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Samuel Holland authored 3 years ago and Marek Vasut committed 3 years ago

Some platforms, like the Allwinner H6, do not have a separate glue layer
around the dwc3. Instead, they rely on the clocks/resets/phys referenced
from the dwc3 DT node itself. Add support for enabling the clocks/resets
referenced from the dwc3 DT node.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Samuel Holland authored 3 years ago and Marek Vasut committed 3 years ago

Resetting an XHCI controller inside xhci_register undoes any register
setup performed by the platform driver. And at least on the Allwinner
H6, resetting the XHCI controller also resets the PHY, which prevents
the controller from working. That means the controller must be taken out
of reset before initializing the PHY, which must be done before calling
xhci_register.

The logic in the XHCI core was added to support the Raspberry Pi 4
(although this was not mentioned in the commit log!), which uses the
xhci-pci platform driver. Move the reset logic to the platform driver,
where it belongs, and where it cannot interfere with other platform
drivers.

This also fixes a failure to call reset_free if xhci_register failed.

Fixes: 0b80371b ("usb: xhci: Add reset controller support")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Samuel Holland authored 3 years ago and Marek Vasut committed 3 years ago

This driver is needed for XHCI to work on the Allwinner H6 SoC. The
driver is copied from Linux v5.10.

Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

- Small fixes to eMMC and SDHCI for Intel Edison

Andy Shevchenko authored 3 years ago and Bin Meng committed 3 years ago

On Intel Tangier the SDHCI #2 provides SD card connection.
Add GPIO card detection for it.

Fixes: 39665bee ("x86: tangier: Enable ACPI support for Intel Tangier")
BugLink: https://github.com/edison-fw/meta-intel-edison/issues/135


Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bin Meng <bmeng.cn@gmail.com>

Andy Shevchenko authored 3 years ago and Bin Meng committed 3 years ago

eMMC is non-removable on Intel Edison board. Fix the DTS accordingly.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

- stm32mp15: fix the used partition name for U-Boot environement with SPL