Faiz Abbas authored 4 years ago and Lokesh Vutla committed 4 years ago

There's an issue with the base board in which the power cycle
circuit takes way longer to power down than expected by mmc core.
code. This prevents the card from enumerating in UHS modes.

Disable UHS modes for this board until a new board revision fixes
the issue.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>

Faiz Abbas authored 4 years ago and Lokesh Vutla committed 4 years ago

Add the appropriate itapdly and clkbuf-sel values required for
some lower speed modes.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>

Faiz Abbas authored 4 years ago and Lokesh Vutla committed 4 years ago

Add configs to support UHS modes for the SD card and HS200 for the eMMC.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>

Faiz Abbas authored 4 years ago and Lokesh Vutla committed 4 years ago

Add configs to support UHS modes for the SD card and HS200 for the eMMC.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>

Faiz Abbas authored 4 years ago and Lokesh Vutla committed 4 years ago

Add support for UHS modes by adding the regulators to power cycle
and voltage switch the card. Also add pinmuxes required for each
node

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>

Faiz Abbas authored 4 years ago and Lokesh Vutla committed 4 years ago

Add support for the main_gpio0 node

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>

Faiz Abbas authored 4 years ago and Lokesh Vutla committed 4 years ago

Add support for regulators to power cycle and switch IO voltage to the
SD card. This enables support for UHS modes.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>

Faiz Abbas authored 4 years ago and Lokesh Vutla committed 4 years ago

Update otap delay values to match with the latest Data Manual[1].

[1] https://www.ti.com/lit/gpn/dra829v



Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>

Faiz Abbas authored 4 years ago and Lokesh Vutla committed 4 years ago

Because of fundamental interface issues in am65x pg1, only the
initial sdhci1 node at 25 MHz was added in the u-boot.dtsi
from which both the base-board.dts and r5-base-board.dts
inherit the node. Move the node out to k3-am65-main.dtsi
where it belongs and add the board specific properties
in base-board.dts and r5-base-board.dts

This ensures dts compatibility with the kernel dts in the
base-board.dts and enables the SD card interface at 50 MHz
and High Speed mode

While we are here, also fix the main_mmc0_pins_default
property to be included and inherit from the base-board.dts
instead of the u-boot.dtsi

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>

Faiz Abbas authored 4 years ago and Lokesh Vutla committed 4 years ago

Use the generic sdhci_set_control_reg() instead of duplicating
in platform driver.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>

Faiz Abbas authored 4 years ago and Lokesh Vutla committed 4 years ago

According to the AM654x Data Manual[1], the setup timing in lower speed
modes can only be met if the controller uses a falling edge data launch.

To ensure this, the HIGH_SPEED_ENA (HOST_CONTROL[2]) bit should be
cleared in default speed, SD high speed, MMC high speed, SDR12 and SDR25
speed modes.

Use the sdhci writeb callback to implement this condition.

[1] http://www.ti.com/lit/gpn/am6546

 Section 5.10.5.16.1

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>

Faiz Abbas authored 4 years ago and Lokesh Vutla committed 4 years ago

With the new SW tuning App note[1], a custom tuning algorithm is
required for eMMC HS200, HS400 and SD card UHS modes. The algorithm
involves running through the 32 possible input tap delay values and
sending the appropriate tuning command (CMD19/21) for each of them
to get a fail or pass result for each of the values. Typically, the
range will have a small contiguous failing window. Considering the
tuning range as a circular buffer, the algorithm then sets a final
tuned value directly opposite to the failing window.

[1] https://www.ti.com/lit/pdf/spract9



Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>

Faiz Abbas authored 4 years ago and Lokesh Vutla committed 4 years ago

Add support for writing new clock buffer select property for both
the am654x and j721e 4 bit IPs

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>

Faiz Abbas authored 4 years ago and Lokesh Vutla committed 4 years ago

DLL need only be enabled for speed modes and clock frequencies at or
above 50 MHz. For speed modes that don't enable the DLL, we need to
configure a static input delay value. This involves reading an optional
itap-del-sel-* value from the device tree and configuring it for the
appropriate speed mode.

Therefore, move all dll configurations to their own functions and gate it
with 50 MHz speed and a minimum mode. If both these conditions are not
satisfied then configure delay chain modes.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>

Faiz Abbas authored 4 years ago and Lokesh Vutla committed 4 years ago

Add Support for AM65x PG2.0. Use the SoC bus framework to fixup
the platform data and do DLL calibration if the revision is 1.0

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>

Faiz Abbas authored 4 years ago and Lokesh Vutla committed 4 years ago

Not all controllers need calibration for the PHY DLL. Add a DLL_CALIB
flag to indicate the same.

Also move the write of trm_icp and driver strength to the set_clock()
function to match the kernel configuration flow.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>

Faiz Abbas authored 4 years ago and Lokesh Vutla committed 4 years ago

Convert the flags field defines to use the BIT() macro.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>

Faiz Abbas authored 4 years ago and Lokesh Vutla committed 4 years ago

There are some speed modes that work without switching the dll on.
Unconditionally switch off the DLL before setting clock frequency to
support this case. The software will automatically enable DLL for speed
modes that require it. This also means the dll_on priv data member is no
longer required.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>

Faiz Abbas authored 4 years ago and Lokesh Vutla committed 4 years ago

Add a set_voltage() function which handles the switch from 3.3V to 1.8V
for SD card UHS modes.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>

Dario Binacchi authored 4 years ago and Lokesh Vutla committed 4 years ago

With commit 38d6b7eb ("spl: Drop bd_info in the data section") you
need to enable this option to boot from mmc.

Signed-off-by: Dario Binacchi <dariobin@libero.it>

Suman Anna authored 4 years ago and Lokesh Vutla committed 4 years ago

The K3 R5F remoteproc driver in U-Boot was upstreamed prior to the
equivalent remoteproc driver in the Linux kernel. Some of the DT
properties used in U-Boot got upstreamed using different names
in Linux kernel.

The modified property names include the R5F cluster mode configuration
property "lockstep-mode"; and three different individual R5F core config
properties - "atcm-enable", "btcm-enable" and "loczrama". The property
names were updated as follows:
  lockstep-mode => ti,cluster-mode
  atcm-enable   => ti,atcm-enable
  btcm-enable   => ti,btcm-enable
  loczrama      => ti,loczrama

Update the K3 R5F remoteproc driver, the corresponding binding, and
all the existing usage in AM65x, J721E and J7200 dts files all at
once to use the new properties and to not break any bisectability.

Signed-off-by: Suman Anna <s-anna@ti.com>

Aswath Govindraju authored 4 years ago and Lokesh Vutla committed 4 years ago

AM65x SoC has two USB subsystems and their corresponding device tree nodes
have the same name but different path. While allocating sequence numbers
for these device tree nodes using alias, phandles can be used to
distinguish them.

Enable config for phandle check while getting sequence number to
distinguish the USB device tree nodes.

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>

David Lechner authored 4 years ago and Lokesh Vutla committed 4 years ago

This disables booting to non-Linux OSes.

This board is uncomfortably close to its 256K size limit, so every
few KB saved helps.

Signed-off-by: David Lechner <david@lechnology.com>

David Lechner authored 4 years ago and Lokesh Vutla committed 4 years ago

This disables the CONFIG_NET setting for LEGO MINDSTORMS EV3. This board
does not have any built-in networking, so it does not make sense to
enable this feature.

This also fixes the warning:

===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================

Signed-off-by: David Lechner <david@lechnology.com>

David Lechner authored 4 years ago and Lokesh Vutla committed 4 years ago

This drops assigning bi_arch_number on LEGO MINDSTORMS EV3. This board
never had its own unique number and since we are using device tree,
we no longer need to pass an arch number to Linux.

Signed-off-by: David Lechner <david@lechnology.com>

David Lechner authored 4 years ago and Lokesh Vutla committed 4 years ago

This sets the serial# environmet variable instead of using ATAGs on
LEGO MINDSTORMS EV3.

Also fix some nomenclature while we are touching this code (Bluetooth
address is not the same as MAC address, EEPROM version is not the same
as board version).

Signed-off-by: David Lechner <david@lechnology.com>

This contributor prefers not to receive mails authored 4 years ago and Lokesh Vutla committed 4 years ago

Move twl4030_power_mmc_init() from board_mmc_power_init() to misc_init_r()
and disable CONFIG_SYS_MALLOC_F. Otherwise U-Boot cannot initialize MMC.
Also disable CONFIG_CMD_SLEEP CONFIG_DM_DEVICE_REMOVE CONFIG_MMC_VERBOSE to
free some space.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Tom Rini <trini@konsulko.com>

- Assorted fixes

Bin Meng authored 4 years ago and Tom Rini committed 4 years ago

Commit dd5c954e ("travis/gitlab/azure: Use -W to avoid warnings check")
added -W to avoid warnings check, but it mistakenly dropped -E for
the world build script in the azure pipelines.

This caused builds on the azure pipelines fail to report warnings. Let's
add it back.

Fixes: dd5c954e ("travis/gitlab/azure: Use -W to avoid warnings check")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Stephen Warren authored 4 years ago and Tom Rini committed 4 years ago

The implementation of pytest_runtest_protocol() must call
pytest_runtest_logstart() and pytest_runtest_logfinish(). This appears to
be necessary even in pytest 5.2.1 judging by the default version of
pytest_runtest_protocol(), but evidently some form of code reorganization
in pytest only made this have a practical effect in the newer version. I'd
previously been under the impression that 100% of the required work of
pytest_runtest_protocol() was handled by the fact it called
runtestprotocol() as its implementation. However, it appears that custom
implementations do need to do a little more than this.

Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

Ramon Fried authored 4 years ago and Tom Rini committed 4 years ago

Add myself as co maintainer to network subsystem
Acked-by: Tom Rini <trini@konsulko.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

Gary Bisson authored 4 years ago and Tom Rini committed 4 years ago

Fixes issues when switching from GPT to MBR partition tables.

Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>

Ravik Hasija authored 4 years ago and Tom Rini committed 4 years ago

Config allows to disable printing contents of fitImage to optimize boottime.

Signed-off-by: Ravik Hasija <rahasij@linux.microsoft.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Heinrich Schuchardt authored 4 years ago and Tom Rini committed 4 years ago

The load command should not silently return to the console prompt if an
invalid block device is specified and no file is loaded.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>

This contributor prefers not to receive mails authored 4 years ago and Tom Rini committed 4 years ago

No version information is used in armv8/fwcall.c therefore do not include
version.h header file. This change prevents recompiling fwcall.o when
SOURCE_DATE_EPOCH changes.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

Ilies CHERGUI authored 4 years ago and Tom Rini committed 4 years ago

Add "-c" option to set the configuration name when
checking the FIT image signature.

Signed-off-by: Ilies CHERGUI <ilies.chergui@gmail.com>

Signed-off-by: Tom Rini <trini@konsulko.com>

- Fix CMD_ACPI dependency in Kconfig
- Correct overflow in __udelay() in TSC timer driver
- Add a devicetree node for eMMC for Coral
- Minor improvements on image loading
- Reduce size of Samus image

Simon Glass authored 4 years ago and Bin Meng committed 4 years ago

With the recent addition of ACPI generation, the image size has got beyond
its current limit.

Samus does not actually use this, nor x86 emulation for PCI ROMs, so
disable both features.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

Simon Glass authored 4 years ago and Bin Meng committed 4 years ago

Enhance the debugging to show the next stage being booted as well as a
dump of the start of the image.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>