Fix doc/board/amlogic/index.rst:
- Add S905W to S905X column.
- Add JetHub devices to the corresponding columns.
- Fix tabs to spaces for table alignment

Add doc/board/amlogic files:
- jethub-j100.rst
- jethub-j80.rst

Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

Add support for new home automation devices.

JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation controller with the following features:
- DIN Rail Mounting case
- Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 512Mb/1GB DDR3
- 8/16GB eMMC flash
- 1 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac, Bluetooth 4.2.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- 2 x gpio LEDS
- GPIO user Button
- 1 x 1-Wire
- 2 x RS-485
- 4 x dry contact digital GPIO inputs
- 3 x relay GPIO outputs
- DC source with a voltage of 9 to 56 V / Passive POE

JetHome Jethub H1 (http://jethome.ru/jethub-h1) is a home automation controller with the following features:
- Square plastic case
- Amlogic S905W (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 1GB DDR3
- 8/16GB eMMC flash
- 2 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth RTL8822CS IEEE 802.11a/b/g/n/ac, Bluetooth 5.0.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- MicroSD 2.x/3.x/4.x DS/HS cards.
- 1 x gpio LED
- ADC user Button
- DC source 5V microUSB with serial console

Patches from:
- JetHub H1
  https://lore.kernel.org/r/20210915085715.1134940-4-adeep@lexina.in
  https://git.kernel.org/amlogic/c/abfaae24ecf3e7f00508b60fa05e2b6789b8f607
- JetHub D1
  https://lore.kernel.org/r/20210915085715.1134940-5-adeep@lexina.in
  https://git.kernel.org/amlogic/c/8e279fb2903990cc6296ec56b3b80b2f854b6c79



Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: removed unused variable value]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

JetHub devices uses its own boot sequence with "rescue" button

Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

Banana Pi BPI-M5 is a credit card format SBC with the following features:
- Amlogic S905X3 quad core Cortex-A55
- Mali-G31 GPU
- 4GB LPDDR4
- 16GB eMMC flash
- 4 USB 3.0
- 1 GbE ethernet
- HDMI output
- 2x LEDS
- SDCard
- 2.5mm Jack with Stereo Audio + CVBS
- Infrared Received
- ADC Button
- GPIO Button
- 40 pins header + 3pins debug header

[narmstrong: add missing CONFIG_SYS_LOAD_ADDR from defconfig]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

The Beelink GS-King X is a variant of the GS King boards but with an internal
USB to SATA bridge and advanced audio features.

[narmstrong: add missing CONFIG_SYS_LOAD_ADDR from defconfig]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

Add documentation bits for the Odroid-HC4.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

The Odroid-HC4 is a variant of the Odroid-C4 board but with a PCIe-SATA bridge
instead of the USB3 ports.

[narmstrong: add missing CONFIG_SYS_LOAD_ADDR from defconfig]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

The SCSI device can be a PCIe adapter, so run pcie enum if enabled.

Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

Add SCSI target to be able to boot from the SATA disks on the Odroid HC4 using
an on-board AHCI PCIe controller.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>

Drop the local USB nodes after Linux 5.14 sync.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

Since Linux commmit [1], the order is fixed with aliases, in order to keep the
MMC device order, set it back to HW order in U-Boot dtsi files.

[1] ab547c4fb39f ("arm64: dts: amlogic: Assign a fixed index to mmc devices")

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

Upstream Linux uses the "amlogic,meson-axg-usb-ctrl" for AXG SoCs.

This adds it to the compatible list for this driver.

Reported-by: Vyacheslav Bocharov <adeep@lexina.in>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Vyacheslav Bocharov <adeep@lexina.in>

Import Amlogic DT changes from Linux commit 7d2a07b76933 ("Linux 5.14"),
dt-bindings clock changes and new meson-g12b-gsking-x.dts,
meson-sm1-bananapi-m5 & odroid-hc4 boards.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

On Amlogic A311D, when the PCIe link fails disabling the related clocks
makes USB fail. For an unknown reason, this doesn happen on the S905D3 SoC.

Mimic the Linux behavior by not considering a link failure a probe failure,
and continue even if the PCIe link is down.

Reported-by: Art Nikpal <email2tema@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

Add the SOC ID for the S905Y2 to board info, see below for before/after
tested with a Radxa Zero board:

SoC:   Amlogic Meson G12A (Unknown) Revision 28:b (30:2)
SoC:   Amlogic Meson G12A (S905Y2) Revision 28:b (30:2)

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

- Use better values for ACPI OEM_VERSION
- Assorted NAND related Kconifg migrations and another dependency fix

The values of CONFIG_NAND_OMAP_ECCSCHEME map to the enum in
include/linux/mtd/omap_gpmc.h for valid ECC schemes.  Make which one we
will use be a choice statement, enumerating the ones which we have
implemented.

Signed-off-by: Tom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_SYS_NAND_U_BOOT_LOCATIONS
   CONFIG_SYS_NAND_U_BOOT_OFFS

Signed-off-by: Tom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_NAND_FSL_ELBC
   CONFIG_NAND_FSL_IFC

Note that a number of PowerPC platforms had previously enabled
CONFIG_NAND_FSL_ELBC without CONFIG_MTD_RAW_NAND, and now they no longer
enable the option, reducing the size of a few functions.

Signed-off-by: Tom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_SYS_NAND_MAX_CHIPS

Signed-off-by: Tom Rini <trini@konsulko.com>

We only include <linux/mtd/rawnand.h> in <nand.h> for the forward
declaration of struct nand_chip, so do that directly.  Then, include
<linux/mtd/rawnand.h> where required directly.

Signed-off-by: Tom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_SYS_NAND_ONFI_DETECTION

Signed-off-by: Tom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_SYS_NAND_5_ADDR_CYCLE

Signed-off-by: Tom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_SYS_NAND_BAD_BLOCK_POS

In order to do this, introduce a choice for HAS_LARGE/SMALL_BADBLOCK_POS
as those are the only valid values.  Use LARGE as the default as no
in-tree boards use SMALL, but it is possible.

Signed-off-by: Tom Rini <trini@konsulko.com>

This code is unused, drop it.

Signed-off-by: Tom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_SYS_NAND_PAGE_COUNT

Signed-off-by: Tom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_SPL_NAND_LOAD
   CONFIG_SYS_NAND_BLOCK_SIZE
   CONFIG_SYS_NAND_PAGE_SIZE
   CONFIG_SYS_NAND_OOBSIZE

Signed-off-by: Tom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_NAND_LPC32XX_MLC

Signed-off-by: Tom Rini <trini@konsulko.com>

Typically platforms will define CONFIG_SYS_NAND_PAGE_COUNT based on
CONFIG_SYS_NAND_BLOCK_SIZE / CONFIG_SYS_NAND_PAGE_SIZE.  Switch to this
in preparation for migrating CONFIG_SYS_NAND namespace to Kconfig.

Cc: Marek Vasut <marex@denx.de>
Cc: Olaf Mandel <o.mandel@menlosystems.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

These platforms do not currently enable NAND, remove these references.

Cc: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

Oleksandr Suvorov authored 3 years ago and Tom Rini committed 3 years ago

SPL_RSA_VERIFY requires SPL_RSA to be enabled. Add correct
dependency.

Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>

This contributor prefers not to receive mails authored 3 years ago and Tom Rini committed 3 years ago

OEM_REVISION is 32-bit unsigned number. It should be increased only when
changing software version. Therefore it should not depend on build time.

Change calculation to use U-Boot version numbers and set this revision
to date number.

Prior this change OEM_REVISION was calculated from build date and stored in
the same format.

After this change macro U_BOOT_BUILD_DATE is not used in other files so
remove it from global autogenerated files and also from Makefile.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

- Assorted OPTEE cleanups
- pinctrl, gpio improvements, assorted livetree migrations
- Assorted pytest improvements

Patrick Delaunay authored 3 years ago and Tom Rini committed 3 years ago

Use dev_ function to support a live tree.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Patrick Delaunay authored 3 years ago and Tom Rini committed 3 years ago

Use dev_ function to read the sides and colour to support a live tree.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Patrick Delaunay authored 3 years ago and Tom Rini committed 3 years ago

Use dev_ function to read the name and boolean to support a live tree.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Simon Glass authored 3 years ago and Tom Rini committed 3 years ago

Add documentation for this so people can try it out. At present it does
not fully work.

Signed-off-by: Simon Glass <sjg@chromium.org>

Simon Glass authored 3 years ago and Tom Rini committed 3 years ago

These tests currently run in a particular sequence, with some of them
depending on the actions of earlier tests.

Add a check for sandbox and reset to a known state at the start of each
test, so that all tests can run in parallel.

Signed-off-by: Simon Glass <sjg@chromium.org>

Simon Glass authored 3 years ago and Tom Rini committed 3 years ago

The -z tests don't really need to be part of the main set. Separate them
out so we can drop the test setup/cleans functions and thus run all tests
in parallel.

Signed-off-by: Simon Glass <sjg@chromium.org>

Simon Glass authored 3 years ago and Tom Rini committed 3 years ago

Update the tests to use separate working directories, so we can run them
in parallel. It also makes it possible to see the individual output files
after the tests have completed.

Signed-off-by: Simon Glass <sjg@chromium.org>