Michael Walle authored 3 years ago and Peng Fan committed 3 years ago

LS1028A SoCs are restricted in what divider values are allowed for HS400
mode. This is basically a port from the corresponding linux driver.

Signed-off-by: Michael Walle <michael@walle.cc>

Trusted Firmware now adds the /reserved-memory subnode to the DT at
runtime[1], putting in the right values.

Drop our hard-coded version, as this might clash with the actual values
(which have also changed), and rely on TF-A to add the node.

[1] https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/7770



Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>

Loading Trusted-Firmware's BL31 at 16KB into DRAM was originally a hack
to allow sharing more code with the other SoCs (which use this offset
in SRAM). However there is no longer a reason for that, as the
problematic macros have been properly separated there.

The latest (and hopefully final) TF-A code drop now changes the load
address to the beginning of DRAM, which is also more easily protected
by the Trustzone memory controller (code to be done).

Adjust the load address of BL31 now, to avoid any issues with
incompatible versions later on (the TF-A patches are about to be merged).

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>

Enable nand and smcc via DT.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

There are several changes which happen in mainline kernel which should get
also to U-Boot. Here is the list of patches from the kernel:

- ARM: zynq: Fix leds subnode name for zc702/zybo-z7
- arm64: dts: zynqmp: Fix leds subnode name for zcu100/ultra96 v1
- arm64: dts: zynqmp: Fix u48 si5382 chip on zcu111
- arm64: dts: zynqmp: Wire up the DisplayPort subsystem
- arm64: dts: zynqmp: Add DisplayPort subsystem
- arm64: dts: zynqmp: Add DPDMA node
- arm64: dts: zynqmp: Enable phy driver for Sata on zcu102/zcu104/zcu106
- arm64: dts: zynqmp: Enable si5341 driver for zcu102/106/111
- arm64: dts: zynqmp: Add DT description for si5328 for zcu102/zcu106
- arm64: dts: zynqmp-zcu100-revC: correct interrupt flags
- arm64: dts: xilinx: align GPIO hog names with dtschema
- arm64: zynqmp: Add Xilinx AES node
- dt: bindings: dma: xilinx: dpdma: DT bindings for Xilinx DPDMA

but also some other changes have been done.
- Using only one compatible string for adxl345 on zturn
- Remove Xilinx internal DP bindings
- Remove USB3.0 serdes configurations
- Remove SATA serdes configuration for zc1232
- Resort nvmem_firmware
- Update nand compatible string
- Aling power-domains property for sd0/1

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

In zynqmp.dtsi file renamed "clk_sys" clock to "controller" and
"clk_flash" clock to "bus" as per upstreamed Arasan NAND driver.
This fixes NAND driver probe failure.

Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Update the following device tree properties for nand flash

- Set software ecc mode.
- Set bch as ecc algo.
- Set read block to 0.

Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

There is Linux driver for these chips that's why add it to device tree.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

EMMC will have bus-width 8 and it is non-removable in general. These
are missing from dt node. Add bus-width and non-removable parameters
to emmc node.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Heinrich Schuchardt authored 3 years ago and Simon Glass committed 3 years ago

On RISC-V the symbols __dyn_sym_start, dyn_sym_end are referenced in
efi_runtime_relocate().

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>

Provide the model information through sysinfo so that it shows up on
boot. For memconfig 4 pins are provided, for 16 combinations. For SKU
ID there are two options:

   - two pins provided in a ternary arrangement, for 9 combinations.
   - reading from the EC

Add a binding doc and drop the unused #defines as well.

Example:

   U-Boot 2021.01-rc5

   CPU:   Intel(R) Celeron(R) CPU N3450 @ 1.10GHz
   DRAM:  3.9 GiB
   MMC:   sdmmc@1b,0: 1, emmc@1c,0: 2
   Video: 1024x768x32 @ b0000000
   Model: Google Coral (memconfig 5, SKU 3)

This depends on the GPIO series:

   http://patchwork.ozlabs.org/project/uboot/list/?series=228126



Signed-off-by: Simon Glass <sjg@chromium.org>

Acked-by: Bin Meng <bmeng.cn@gmail.com>

It is not possible to remove the state before driver model is uninited,
since the devices are allocated in the memory buffer. Also it is not
possible to uninit driver model afterwards, since the RAM has been
freed.

Drop the uninit altogether, since it is not actually necessary.

Signed-off-by: Simon Glass <sjg@chromium.org>

The _SUPPORT suffix is from an earlier time and interferes with use of
the CONFIG_IS_ENABLED() macro. Rename the option to drop the suffix.

Tidy up the TODO that prompted this.

Signed-off-by: Simon Glass <sjg@chromium.org>

At present sandbox removes its executable after failing to run it,
since there is no other way that it would get cleaned up.

However, this is actually only wanted if the image was created within
sandbox. For the case where the image was generated by the build system,
such as u-boot-spl, we don't want to delete it.

Handle the two code paths accordingly.

Signed-off-by: Simon Glass <sjg@chromium.org>

This currently hangs and it is not necessary in any case. Drop the code
when booting from coreboot.

Signed-off-by: Simon Glass <sjg@chromium.org>

When booting from coreboot there is no need to notify the FSP of anything,
since coreboot has already done it. Nor it is possible, since the FSP
details are not provided by coreboot.

Skip it in this case.

Signed-off-by: Simon Glass <sjg@chromium.org>

When booting from coreboot the FSP video information is no-longer
available. Enable the coreboot driver so that we can get some sort of
display in this case.

Signed-off-by: Simon Glass <sjg@chromium.org>

At present the debug UART is only set up in SPL, on the assumption that
the boot flow will always pass through there. When booting from coreboot,
SPL is not used, so the debug UART is not available.

Move the code into a common place so that it can be used in U-Boot proper
also. Add the required init to start_from_spl.S as well.

Signed-off-by: Simon Glass <sjg@chromium.org>

When CONFIG_ACPIGEN is not enabled the CPU code does not build. Fix this
by moving things around.

Signed-off-by: Simon Glass <sjg@chromium.org>

This driver cannot work when booted from coreboot, since the FSP
information is not available. Disable it in that case, so that the
coreboot video driver can be used instead.

Signed-off-by: Simon Glass <sjg@chromium.org>

Move this code into a generic location so that it can be used by other x86
boards which want to boot from coreboot. Also ensure that this is called
if booting from coreboot.

Signed-off-by: Simon Glass <sjg@chromium.org>

Quite a few new tag types have been added over the years. Bring these into
U-Boot so that all required tags can be parsed.

Add a proper comment to struct sysinfo_t while we are here, since many of
the meanings are not obvious.

Signed-off-by: Simon Glass <sjg@chromium.org>

It is useful to be able to parse coreboot tables on any x86 build which is
booted from coreboot. Add a new Kconfig option to enable this feature and
move the code so it can be used on any board, if enabled.

Signed-off-by: Simon Glass <sjg@chromium.org>

Add new timestamp codes that are present in coreboot, so that we can decode
these in U-Boot.

At present TS_U_BOOT_START_KERNEL is used twice. It should only be used
just before jumping to Linux, so update the other call site to use
TS_START_KERNEL.

Signed-off-by: Simon Glass <sjg@chromium.org>

This all relates to the sysinfo structure provided by coreboot. Put the
timestamp definitions into the same file as the others. Tidy up a few
comments at the same time.

Signed-off-by: Simon Glass <sjg@chromium.org>

It is possible to boot U-Boot for chromebook_coral either 'bare metal' or
from coreboot. In the latter case we want to provide access to the coreboot
sysinfo tables. Move the definitions into a file available to any x86
board.

Signed-off-by: Simon Glass <sjg@chromium.org>

In some cases CBFS does not start with a header but is just a collection
of files. It is possible to support this so long as the size of the CBFS
is provided.

Update the cbfs_init_mem() function to support this.

Signed-off-by: Simon Glass <sjg@chromium.org>

Since the recent bug fix, it doesn't matter which GPIO phandle is used so
long as the GPIO number is right. Still, we may as well use the correct
one to avoid confusion.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>

At present the eMMC device does not have an alias so it appears after
the SD card which is device 1. There is no device 0 which is odd.

Make the eMMC device be the first one. Update the boot script to use the
new device.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>

Vincent Stehlé authored 4 years ago and Simon Glass committed 3 years ago

Having an rng in the sandbox is useful not only for tests but also for e.g.
UEFI. Therefore, copy the rng node from test.dts to sandbox.dtsi.

In the case of UEFI, it can then be verified with `efidebug dh' that a
"Random Number Generator" protocol is indeed present.

This also fixes the following `bootefi' error:

  Missing RNG device for EFI_RNG_PROTOCOL

Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Cc: Simon Glass <sjg@chromium.org>

This cannot be used since the previous #elif has already dealt with SPL.
Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>

We don't need to spell out the separate pieces of U-Boot phase binaries
anymore. Revert to using the simple entry and let binman do the expansion
itself as needed.

Signed-off-by: Simon Glass <sjg@chromium.org>

With Apollo Lake, SPL is placed in read-only memory. Set this new option
so that OF_PLATDATA_INST can be used.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>

These devices are not actually built in TPL but are currently active in
the TPL devicetree. For of-platdata-inst this means that we will try to
generate devices for them, which fails.

Update them to be active only in U-Boot proper.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>

We don't normally need this driver in TPL/SPL, so drop it for now. It can
be enabled by individual boards if needed.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>

With TPL we don't need full PCI support and it adds to code size. Instead,
a simple_bus driver is good enough to be able to read and write the PCI
config and do a little basic setup.

So at present there are two drivers in U-Boot called pci_x86. One is in
UCLASS_PCI, used in SPL and U-Boot proper. The other is in
UCLASS_SIMPLE_BUS and used only in TPL.

Add a tag to tell dtoc about this, so it knows which one to use when
generating the devices and uclasses.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>

With the standard of-platdata we must fix up driver_data manually. With
of-platadata-inst this is not necessary, since it is added to the device
by dtoc.

Update the code to handle this.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>

This enum is needed to generate build-time devices. Tell dtoc where to
find the header, to avoid compile errors in the generated code.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>

The dm.h header should come first. In fact it needs to, since otherwise
the driver model definitions are not available to dt-structs.h

Fix this, since it causes problems with OF_PLATDATA_INST.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>

Collect this together in one place, so driver model can access set it up
in a new place if needed.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>