- Sep 14, 2017
-
-
To remove the assignment of CONFIG_SYS_EXTRA_OPTIONS option, which is deprecated, use the CONFIG_XXXX_BOOT options to indicate the boot media, and the SoC is selected by the board. Signed-off-by:Wenyou Yang <wenyou.yang@microchip.com>
-
As said in READRE.kconfig, include/configs/*.h will be removed after all options are switched to Kconfig. As the first step, remove the follow line from include/configs/*.h. #include <asm/hardware.h> Signed-off-by: -
The SAMA5D27-SiP (System in Package) integrates the SAMA5D2 with 1Gbit DDR2-SDRAM in a single package. The SAMA5D27 SOM1 embeds a 64Mbit QSPI flash, KSZ8081 Phy and Mac-address EEPROM. Signed-off-by:
Simon Glass <sjg@chromium.org>
-
Because before switching to a lower clock source, we must switch the clock source first instead of last. So before configuring the PMC_MCKR register, invoke at91_mck_init_down() first. As said in datasheet, the the size of SPL must not exceed the maximum size allowed(64Kbytes). Signed-off-by:
-
In order to display the company's logo via the API of DM_VIDEO, and add the logo files of both Atmel and Microchip. Signed-off-by:
-
- Sep 13, 2017
-
-
This converts the following to Kconfig: CONFIG_EMIF4 CONFIG_SDRC Signed-off-by:
Adam Ford <aford173@gmail.com> Reviewed-by:
Stefano Babic <sbabic@denx.de>
-
In mancy cases both CONFIG_ENV_OFFSET and CONFIG_ENV_ADDR point to an otherwise-unused SMNAND_ENV_OFFSET. This patch will set both CONFIG_ENV_OFFSET and CONFIG_ENV_ADDR to whatever value was defined by SMNAND_ENV_OFFSET. Signed-off-by:
-
- Sep 12, 2017
-
-
Some drivers in Linux (ex. drivers/mtd/nand/denali.c) use ioread*/iowrite* accessors. Import them to make drivers more synced. I copied code from include/asm-generic/io.h of Linux. Signed-off-by:Masahiro Yamada <yamada.masahiro@socionext.com>
-
Import include/linux/dma-direction.h from Linux 4.13-rc7 and delete duplicated definitions of enum dma_data_direction. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com>
-
Much of the AM3517 functions are copies of the standard definitions used in ti_omap3_common.h. Moving to include a common file reduces the amount of duplicative code and clutter. A few AM3517 specific functions (like EMIF4) are explictly defined and a few items are undefined or redefined, but overall the number of lines of code shink. Signed-off-by:
Derald D. Woods <woods.technical@gmail.com>
-
The PMMC firmware should be bundled with the FIT image for HS devices, remove the steps that load and install this firmware outside of FIT. Signed-off-by:Andrew F. Davis <afd@ti.com>
-
Add a new image type representing TI Power Management Micro-Controller (PMMC) Firmware image type. Signed-off-by: -
This works (roughly) the same way as linux's, but we currently always print lower-case (ie. we just keep %pUB and %pUL for compat with linux), mostly just because that is what uuid_bin_to_str() supports. %pUb: 01020304-0506-0708-090a-0b0c0d0e0f10 %pUl: 04030201-0605-0807-090a-0b0c0d0e0f10 It will be used by a later efi_loader paths for efi variables and for device-path-to-text protocol, and also quite useful for debug prints of protocol GUIDs. Signed-off-by:
Rob Clark <robdclark@gmail.com> Tested-by:
Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by:
-
We'll eventually want these in a few places in efi_loader, and also vsprintf. Signed-off-by: -
Currently, all fixed-clock declared in "clocks" node in device tree can be binded by clk_fixed_rate.c driver only if each of them have the "simple-bus" compatible string. This constraint has been invoked here [1]. This patch offers a solution to avoid adding "simple-bus" compatible string to nodes that are not busses. [1] https://patchwork.ozlabs.org/patch/558837/ Signed-off-by:
Patrice Chotard <patrice.chotard@st.com> Reviewed-by:
-
Simon Glass authored
Add a convenience macro to iterate over subnodes of a node. Make use of this where appropriate in the code. Signed-off-by: -
There is an overflow problem when taking the size instead of the number of blocks in blk_create_device(). This results in a wrong device size: the device apparent size is its real size modulo 4GB. Using the number of blocks instead of the device size fixes the problem and is more coherent with the internals of the block layer. Signed-off-by:
Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by:
-
- Sep 11, 2017
-
-
Add the code to set the ethernet mac address from eeprom by using the common code from the common folder. Signed-off-by:
-
Replace the code to set the ethernet mac address with the code from the common folder. Signed-off-by:
-
Select dtb name for am57xx BeagleBoard-X15 revC Signed-off-by:
Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
-
Sync all dra7* specific dts files with the upstream kernel including changes queued for 4.14 https://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap.git/log/?h=omap-for-v4.14/dt-v3 Signed-off-by:
Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: -
Select dtb name for dra76-evm. Reviewed-by:
Lokesh Vutla <lokeshvutla@ti.com> -
ldo4 is used to poweron mmc on dra76-evm. Enable it. Reviewed-by:
Lokesh Vutla <lokeshvutla@ti.com> -
It is not necessary that ldo1 is used to power on mmc. So, add support for passing ldo registers for powering on mmc. Reviewed-by:
Lokesh Vutla <lokeshvutla@ti.com> -
Hou Zhiqiang authored
Enabled PCIe support and PCI command feature. Signed-off-by:
Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by:
York Sun <york.sun@nxp.com>
-
Ashish Kumar authored
This patch adds support for RGMII protocol NXP's LDPAA2 support RGMII protocol. LS1088A is the first Soc supporting both RGMII and SGMII. Signed-off-by:
Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Signed-off-by:
Amrita Kumari <amrita.kumari@nxp.com> Signed-off-by:
Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by:
-
Ashish Kumar authored
This patch add support of LS1088AQDS platform. The LS1088A QorIQTM Development System (QDS) is a high-performance computing, evaluation, and development platform that supports the LS1088A QorIQ Architecture processor. Signed-off-by:
Shaohui Xie <Shaohui.Xie@nxp.com> Signed-off-by:
-
Ashish Kumar authored
LS1088A is an ARMv8 implementation. The LS1088ARDB is an evaluatoin platform that supports the LS1088A family SoCs. This patch add basic support of the platform. Signed-off-by:
Alison Wang <alison.wang@nxp.com> Signed-off-by:
Raghav Dogra <raghav.dogra@nxp.com> Signed-off-by:
-
Ashish Kumar authored
CoreLink Cache Coherent Interconnect (CCI) provides full cache coherency between two clusters of multi-core CPUs and I/O coherency for devices and I/O masters. This patch add new config option SYS_FSL_HAS_CCI400 and moves existing register space definaton of CCI-400 bus to fsl_immap to be shared. CONFIG_SYS_CCI400_ADDR is replaced with SYS_CCI400_OFFSET in Kconfig. Signed-off-by:
-
MX6Q/QP IPU operates at 264MHz and MX6DL IPU at 198MHz. When running a SPL target, which supports multiple MX6 variants we cannot properly setup the IPU clock frequency via CONFIG_IPUV3_CLK option as such decision is done in build-time currently. Remove the CONFIG_IPUV3_CLK option and let the IPU clock frequency be configured in run-time on mx6. Reported-by:
Eric Nelson <eric@nelint.com> Signed-off-by:
Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by:
Anatolij Gustschin <agust@denx.de>
-
- Sep 10, 2017
-
-
This converts the IDE driver to driver model so that block read and write are fully functional. Fixes: b7c6baef ("x86: Convert MMC to driver model") Reported-by:
Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: -
So far these are using magic numbers. Replace them with macros. Signed-off-by:
Bin Meng <bmeng.cn@gmail.com>
Reviewed-by:
-
- Sep 08, 2017
-
-
This migrates ASIX, ASIX88179, MCS7830, RTL8152 and SMSC95XX to Kconfig. Update defconfigs. Signed-off-by:
Chris Packham <judge.packham@gmail.com> Reviewed-by:
-
CONFIG_USB_HOST_ETHER is the framework that the drivers are dependent on USB_HOST_ETHER. Use this as a menu and move the existing LAN75XX and LAN78XX options under new menu. Finally update the defconfigs that need CONFIG_USB_HOST_ETHER. Signed-off-by:
-
This is not a valid option. Drop it. Signed-off-by:
-
This is not a valid option. Drop it. Signed-off-by:
-
- Sep 07, 2017
-
-
Remove a comment line refering to a non-existent file. Signed-off-by: -
The inline documentation of vsprintf mentions a parameter size which does not exist in the function declaration. int vsprintf(char *buf, const char *fmt, va_list args); Signed-off-by:
-
- Sep 06, 2017
-
-
Since commit 842778a0 ("usb: gadget: g_dnl: only set iSerialNumber if we have a serial#") "fastboot devices" stopped to show correct device serial number for TI boards, showing this line instead: ???????????? fastboot This is because serial# env variable could be set after g_dnl gadget was initialized (e.g. by using env_set() in the board file). To fix this, let's update internal serial number variable (g_dnl_serial) when "serial#" env var is changed. Signed-off-by:
Sam Protsenko <semen.protsenko@linaro.org> Cc: Felipe Balbi <felipe.balbi@linux.intel.com> Tested-by:
Heiko Schocher <hs@denx.de> Acked-by:
Łukasz Majewski <lukma@denx.de> Reviewed-by:
Marek Vasut <marex@denx.de>
-
- Sep 03, 2017
-
-
- Pass MTDPARTS kernel arguments to kernel - Use Kconfig CONFIG_NAND instead of CONFIG_SYS_EXTRA_OPTIONS="NAND" - Call 'usb_stop' on kernel start - Update Falcon mode setup to match other OMAP3 boards - Use "uEnv.txt" as boot script instead of "boot.scr"
-
