-
u-boot-stm32-20210113
- Enable logging features for stm32mp15 boards - Update MAINTAINERS emails for STI and STM32 - Activate OF_LIVE for ST stm32mp15 boards - Switch to MCO2 for PHY 50 MHz clock for DHCOM boards - Correction in stm32prog command on uart: always flush DFU on start command - Update USB-C power detection algorithm on DK boards
-
-
u-boot-stm32-20210106
- Fix GPIO hog flags on DHCOM boards
-
u-boot-stm32-20201209
- Manage CONFIG_ENV_EXT4_DEVICE_AND_PART in stm32mp1 board - Update ARM STI and ARM STM STM32MP Arch maintainers emails - Enable internal pull-ups for SDMMC1 on DHCOM SoM
-
u-boot-stm32-20201125
- STM32 MCU's DT update - Add DHCOM based STM32MP15x PicoITX board - Correct ALIGN macro usage for on syram for SPL dcache support - Fixes on DHCOM: uSD card-detect GPIO and Drop QSPI CS2 - Fix compilation issue for spl_mmc_boot_partition - Fix MTD partitions for serial boot - Add support of MCU HOLD BOOT with reset for stm32 remoteproc (prepare alligneent with kernel DT) - Correct bias information and support in STM32 soc and STMFX - Support optional vbus in usbphyc - Update FIT examples to avoid kernel zImage relocation before decompression
-
-
u-boot-stm32-20201021
- Activate CMD_EXPORTENV/CMD_IMPORTENV/CMD_ELF for STM32MP15 defconfig - Fix stm32prog command: parsing of FlashLayout without partition - Update MAINTAINERS for ARM STM STM32MP - Manage eth1addr on dh board with KS8851 - Limit size of cacheable DDR in pre-reloc stage in stm32mp1 - Use mmc_of_parse() to read host capabilities in mmc:sdmmc2 driver
-
-
u-boot-stm32-20201003
- stm32mp: DT alignment with Linux 5.9-rc4 - stm32mp: convert drivers to APIs which support live DT - stm32mp: gpio: minor fixes
-
u-boot-stm32-20201002
- Fixup SPI-NOR boot on AV96 board
-
u-boot-stm32-20200909
- fixes on AV96 board: pull up on UART4 RX and adjust PLL4
-
-
-
u-boot-stm32-20200813
- Use IS_ENABLED to prevent ifdef in board_key_check for STM32MP - Add STM32 FMC2 EBI controller driver - Fix dwc3-sti-glue which allows STiH410-B2260 to boot again - Add fitImage its entry for 587-200 DHCOR SoM - Add both PDK2 and DRC02 DT into DHCOM fitImage its - Fix DHCOM KS8851 ethernet MAC address - Remove stm32mp1 board.c file - Use const for struct node_info in board stm32mp1.c file
-
-
u-boot-stm32-20200729
- fix SPL boot issue due to early dbgmcu_init() call - fix SPL boot issue due to dcache memory region configuration - add support of CONFIG_ENV_IS_IN_MMC - add specific SD/eMMC partition for U-Boot enviromnent - enable env in SPL - use "env info -q" to remove log during boot - remove env location override for dh_stm32mp1 - update management of misc_read - check result of find_mmc_device in stm32prog - use regulator_set_enable_if_allowed for disabling vdd supply in usbphyc - enable CMD_ADTIMG flag to handle Android images - device tree alignment with Linux Kernel v5.8-rc1 - remove hnp-srp-disable for usbotg on dk1 - add reset support to uart nodes on stm32mp15x - use correct weak function name spl_board_prepare_for_linux - use cd-gpios for ST and DHSOM boards - add seeed studio odyssey-stm32mp157c board support - move ethernet PHY into SoM DT - add DHSOM based DRC02 board support
-
-
u-boot-stm32-20200707
- arch and board update for stm32mp15: - use OPP information in device tree for 800MHz/650MHz support - ram: inprovments of test command - solve boot on closed chip when access to DBGMCU_IDC is protected - stm32prog command: Add "device anme" during USB enumeration - update configs: activate WATCHDOG and 'env erase' command, increase teed partition, support SD card after NOR boot by default and use env info in env_check - some sboard cleanups: gpio hog in dh board, specific driver for type-c stusb1600 controller code in a driver move part of code in spl.c and in common directory - fix STM32 compatible for dwc_eth_qos driver - support of new pinctrl ops get_dir_flags/set_dir_flags in stm32 and stmfx drivers - vrefbuf: fix a possible overshoot when re-enabling
-
-