- Jun 23, 2021
-
-
Michal Simek authored
Update the psgtr clock indexing for couple of zynqmp boards. Signed-off-by:Michal Simek <michal.simek@xilinx.com>
-
Michal Simek authored
K26 has EMMC and SD and default 0 is not working when system is booting out of SD which is controller 1. Add controller autodetection via mmc_get_env_dev(). The same code is used for distro_boot selection done in board_late_init(). bootseq variable can't be reused because this is called so late. Signed-off-by: -
Michal Simek authored
Add psu_init_gpl file for getting SPL to work directly from the tree. Signed-off-by: -
Michal Simek authored
Rename amba to AXI. Based on Xilinx Zynq TRM (Chapter 5) chip is "AXI point-to-point channels for communicating addresses, data, and response transactions between master and slave clients. This ARM AMBA 3.0..." Issues are reported as: .. amba: $nodename:0: 'amba' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$' >From schema: ../github.com/devicetree-org/dt-schema/dtschema/schemas/simple-bus.yaml Similar change has been done for Xilinx ZynqMP SoC. Signed-off-by:
-
Michal Simek authored
Enable gpio driver on these boards. GPIOs can be used on any board. Signed-off-by: -
Michal Simek authored
SVDs are using different name which can't be handled via zynqmp_devices structure. That's why introduce zynqmp_detect_svd_name() which checks ID code for these devices and show proper name for them. Signed-off-by: -
Michal Simek authored
Enabling EFI secure boot which is required for EBBR specification. Enabling this will fix "RT.SetVariable - Create one Time Base Auth Variable, the expect return status should be EFI_SUCCESS" Signed-off-by: -
T Karthik Reddy authored
CONFIG_ZYNQMP_FIRMWARE enables zynqmp firmware driver. Signed-off-by:T Karthik Reddy <t.karthik.reddy@xilinx.com>
-
Ashok Reddy Soma authored
From U-Boot, loading application on RPU core 0 is fine but loading on core 1 is not handled properly. Lock-step mode needs both the R5 cores to be initialized and it is working fine. Whereas in SPLIT mode individual R5 cores needs to be initialized as they need to execute differenet applications. Handle both these lock-step and split modes by propagating mode and RPU core number(4 for RPU0 and 5 for RPU1) for various functions and by adding conditions in those functions. Signed-off-by:
Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by:
-
Michal Simek authored
The Linux commit f69629919942 ("dt-bindings: sram: Convert SRAM bindings to json-schema") converted binding to yaml and some missing required properties started to be reported. Align binding based on it. The patch is fixing these warnings: .../zynq-zc702.dt.yaml: sram@fffc0000: '#address-cells' is a required property .../zynq-zc702.dt.yaml: sram@fffc0000: '#size-cells' is a required property .../zynq-zc702.dt.yaml: sram@fffc0000: 'ranges' is a required property >From schema: .../Documentation/devicetree/bindings/sram/sram.yaml Signed-off-by: -
Michal Simek authored
The Linux commit f8f79fa6bb25 ("dt-bindings: at25: convert the binding document to yaml") converted binding to yaml and 3 deprecated properties pop up. The patch is fixing these warnings: .../zynq-zc770-xm013.dt.yaml: eeprom@2: 'pagesize' is a required property .../zynq-zc770-xm013.dt.yaml: eeprom@2: 'size' is a required property .../zynq-zc770-xm013.dt.yaml: eeprom@2: 'address-width' is a required property >From schema: .../Documentation/devicetree/bindings/eeprom/at25.yaml by converting them to new binding. Signed-off-by: -
Jorge Ramirez-Ortiz authored
Use the ZDMA channel 0 to initialize the DRAM banks. This avoid spurious ECC errors that can occur when accessing unitialized memory. The feature is enabled by setting the option CONFIG_SPL_ZYNQMP_DRAM_ECC_INIT and providing the following data: SPL_ZYNQMP_DRAM_BANK1_BASE: start of memory to initialize SPL_ZYNQMP_DRAM_BANK1_LEN : len of memory to initialize (hex) SPL_ZYNQMP_DRAM_BANK2_BASE: start of memory to initialize SPL_ZYNQMP_DRAM_BANK2_LEN : len of memory to initialize (hex) Setting SPL_ZYNQMP_DRAM_BANK_LEN to 0 takes no action. Signed-off-by:
Jorge Ramirez-Ortiz <jorge@foundries.io> Signed-off-by:
-
Michal Simek authored
pca953x also depends on i2c that's why add dependency to Kconfig. Where GPIO is enabled but I2C compilation error pops up. Signed-off-by:
Heiko Schocher <hs@denx.de>
-
- Jun 22, 2021
-
-
MSYS2 Windows build started to fail since yesterday (Jun 21): checking keyring... checking package integrity... error: gcc-libs: signature from "David Macek <david.macek.0@gmail.com>" is unknown trust :: File /var/cache/pacman/pkg/gcc-libs-10.2.0-1-x86_64.pkg.tar.zst is corrupted (invalid or corrupted package (PGP signature)). error: gcc: signature from "David Macek <david.macek.0@gmail.com>" is unknown trust :: File /var/cache/pacman/pkg/gcc-10.2.0-1-x86_64.pkg.tar.zst is corrupted (invalid or corrupted package (PGP signature)). error: failed to commit transaction (invalid or corrupted package) Errors occurred, no packages were upgraded. Switching to the latest installer (version 20210604) seems to fix it. Signed-off-by:
Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com> Tested-by:
-
- Jun 18, 2021
-
-
-
clean up octeontx_smi_probe by using the live-tree API. Signed-off-by:
Tim Harvey <tharvey@gateworks.com> Reviewed-by:
Stefan Roese <sr@denx.de> Reviewed-by:
Ramon Fried <rfried.dev@gmail.com>
-
If the environment does not have "soc" or "board" set, and fdtdir option is specified in extlinux.conf, the bootloader will crash whilst dereferencing a null pointer. Add a guard against null soc or board. Fixes a crash of qemu-riscv64_smode configuration, which does not have CONFIG_SYS_SOC defined. Signed-off-by:
Dimitri John Ledkov <xnox@ubuntu.com> Reviewed-by:
-
Linux uses the prefix "ethernet" whereas u-boot uses "eth". This is from the linux tree: $ grep "eth[0-9].*=.*&" arch/**/*dts{,i}|wc -l 0 $ grep "ethernet[0-9].*=.*&" arch/**/*dts{,i}|wc -l 633 In u-boot device trees both prefixes are used. Until recently the only user of the ethernet alias was the sandbox test device tree. This changed with commit fc054d56 ("net: Introduce DSA class for Ethernet switches"). There, the MAC addresses are inherited based on the devices sequence IDs which is in turn given by the device tree. Before there are more users in u-boot and both worlds will differ even more, rename the alias prefix to "ethernet" to match the linux ones. Also adapt the test cases and rename any old aliases in the u-boot device trees. Cc: David Wu <david.wu@rock-chips.com> Signed-off-by:Michael Walle <michael@walle.cc> Reviewed-by:
Fabio Estevam <festevam@gmail.com> Reviewed-by:
Simon Glass <sjg@chromium.org>
-
If the environment variable "ethact" is not set, the first device in the uclass is returned. This depends on the probing order of the ethernet devices. Moreover it is not not configurable at all. Try to return the ethernet device with sequence id 0 first which then can be configured by the aliases in a device tree. Fall back to the old mechanism in case of an error. Signed-off-by:
-
Commit 4f0278da ("net: sun8i-emac: Lower MDIO frequency") leads to network failure on the OrangePi PC. => dhcp sun8i_emac_eth_start: Timeout According to the commit message the change of the MDIO frequency is only required for external PHYs. Fixes: 4f0278da ("net: sun8i-emac: Lower MDIO frequency") Signed-off-by:
Heinrich Schuchardt <xypron.glpk@gmx.de>
-
Add SynQuacer's NETSEC GbE controller driver. Since this driver will load the firmware from SPI NOR flash, this depends on CONFIG_SYNQUACER_SPI=y. Signed-off-by:
Jassi Brar <jaswinder.singh@linaro.org> Reviewed-by:
-
Revert some changes of commit 3a97da12 ("net: dwc_eth_qos: add dwc eqos for imx support") that were probably added by mistake. One of these changes can lead to received data corruption (enabling FUP and FEP bits). Another causes invalid register rxq_ctrl0 settings for some platforms. And another makes some writes at unknown memory location. Fixes: 3a97da12 ("net: dwc_eth_qos: add dwc eqos for imx support") Signed-off-by:
Daniil Stas <daniil.stas@posteo.net> Cc: Ye Li <ye.li@nxp.com> Cc: Fugang Duan <fugang.duan@nxp.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Ramon Fried <rfried.dev@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by:
-
Disabling clk_ck clock leads to link up status loss in phy, which leads to auto-negotiation restart before each network command execution. This issue is especially big for PXE boot protocol because of auto-negotiation restarts before each configuration filename trial. To avoid this issue don't disable clk_ck clock after it was enabled. Signed-off-by:
-
commit f1bcad22 ("net: e1000: add support for writing to EEPROM") adds support for storing hwaddr in EEPROM however i210 devices do not support this and thus results in errors such as: Warning: e1000#0 failed to set MAC address' Check if a flash device is present and if not return -ENOSYS indicating this is not supported. Signed-off-by:
-
Signed-off-by:
Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by:
-
- Jun 17, 2021
-
-
https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriqTom Rini authored
- fsl-qoriq: Bug fixes related pfe, eth, thermal node, vid.c, cpu release, mmc, usb, env, etc for Layerscape boards - powerpc: Update Maintainers for some boards.
-
-
Priyanka Jain authored
Add Priyanka Jain as MAINTAINER for T2080RDB_revD_defconfig, T2080RDB_revD_NAND_defconfig, T2080RDB_revD_SDCARD_defconfig and T2080RDB_revD_SPIFLASH_defconfig Signed-off-by:Priyanka Jain <priyanka.jain@nxp.com>
-
Change the USB erratum number A-050106 to A-050204 as A-050106 is a duplicate and never be published. Fixes 0cfa00cd (“armv8: Add workaround for USB erratum A-050106”) Signed-off-by:
Ran Wang <ran.wang_1@nxp.com> [Rebased] Signed-off-by:
-
Under DM, we rely on u-boot's device tree to provide the correct PHY addresses. The board_fix_fdt callback is intended to be used for device tree fixups before relocation. Unfortunately, this isn't an option when booting from flash since the device tree isn't writable before relocation. This patch introduces the CONFIG_T2080RDB_REV_D option to signal that a board revision D or up is the target. The config option is used to set the correct Aquantia PHY address in the board's u-boot device tree. Defconfig files with the option enable explicitly are added for convenience. Signed-off-by:
Camelia Groza <camelia.groza@nxp.com> Reviewed-by:
-
The T2080RDB boards revisions D and up have updated 10G Aquantia PHYs connected to MAC1 and MAC2. The second Aquantia PHY is located at a different address on the MDIO bus compared to rev C (0x8 instead of 0x1). Fix-up the Linux device tree to update the PHY address for the second Aquantia PHY on boards revisions D and up. Also rename the PHY node to reflect the changes. Signed-off-by:
-
Detect and print the board revision version based on the CPLD registers. Signed-off-by:
-
Both DM_ETH and DM_PCI are enabled for the T2080RDB board. Remove the board_eth_init() callback and the non-DM_ETH code paths since they are not needed anymore. Signed-off-by:
-
A system clock of 66MHz was chosen for the pg-wcom-ls102xa. Compared to the Evalboard, this corresponds to a reduction of 1/3. The system counter clock should have been reduced accordingly, but that was not the case, so we had a system time that was 1/3 behind the real time. This patch corrects the system counter clock to 8.333MHz = 66.667MHz / 8. Signed-off-by:
Rainer Boschung <rainer.boschung@hitachi-powergrids.com> Signed-off-by:
Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com> Reviewed-by:
-
This patch adds the front led initialization and the application buffer enable to the eraly board inititlaization. Signed-off-by:
-
In order to improve power consumption ls102x allows to disable peripherals that are not in use. This patch follows SELI8 HW design description and disables peripherals that are not in use in our designs, the same configuration is applicable and for EXPU1. This patch uses available hwconfig option for updating ls102x device disable configuration. Signed-off-by:
-
The default behavior in the latest u-boot revisions is to rotate the active net device to the next available if the requested link is not established. For our ls102x based devices this would mean that if active debug net device is not available, u-boot will rotate and set the next net device that is one of the estar adapters. To return from this situation manual action to set correct ethact adapter will be needed and this can be annoying when working in debug mode. Setting ethrotate=no will disable net adapter rotation and will make sure that the primary adapter is always used. Signed-off-by:
-
This is most probably a typo, and in older u-uboot versions is same as 'saveenv', in the newer uboot versions there is a separate 'save' command that is different from 'saveenv'. Signed-off-by:
-
In our designs we reserve PRAM area at the end of the RAM, and in order this area to be visible and taken into account by the u-boot memory mgmt CONFIG_PRAM has to be defined. Signed-off-by:
-
From production view this is standard test executed during production on all linux based foxmc cards. On CENT2 HW defined memory region is zero means that some DDR accesses are done by memory_post_dataline and memory_post_addrline but pattern tests are skipped that's why mem_regions is fast there. On ls102x for the complete DDR region of 1GiB memory_regions_post_test takes approx. 4min and this is too much for production, so this patch defines only 1MiB region as compromise. Signed-off-by:
-
