- ae350 related dts fixes.

Current logic in riscv_get_ipi() for Andes PLICSW does not look
correct. The mask to test IPI pending bits for a hart should be
left shifted by (8 * gd->arch.boot_hart), just the same as what
is done in riscv_send_ipi().

Fixes: 8b3e97ba ("riscv: add functions for reading the IPI status")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Tested-by: Rick Chen <rick@andestech.com>

The doc says CONFIG_SKIP_LOWLEVEL_INIT is in ax25-ae350.h, while
actually it is not. Remove it.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>

At present the AE350 SPL defconfig is using OF_PRIOR_STAGE. The
intention was to use gdb to load device tree before running U-Boot
SPL/proper from RAM. When we switch to OF_SEPARATE we will have to
use our own DT but without "u-boot,dm-spl" in several essential
nodes, SPL does not boot.

Let's add all the required "u-boot,dm-spl" for SPL config.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>

All the device nodes that refer to plic0 as their interrupt parent
have 2 cells encoded in their interrupts property, but plic0 only
provides 1 cell in #interrupt-cells which is incorrect.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>

PLIC nodes don't have child nodes, so #address-cells is not needed.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>

There are two spaces before "debug' in bootargs. Drop one.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>

The SPDX license header is currently missing. Add one.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>

u-boot-imx-20210616
-------------------

- imxrt : fixes, USB, imxrt1020-evk
- imx8m:
	fix for verdin-imx8mm
	Add conga-QMX8 board
- imx6 :
	documentation for pico-imx6:
	Add SeeedStudio NPI-IMX6ULL Support
	ventana: DM PCI
- imx7d:
	added SMEGW01 board

CI : https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/7765

- Turris: Fix bootcmd_rescue (Pali)

Pali Rohár authored 3 years ago and Stefan Roese committed 3 years ago

One of the points of putting the rescue boot command into default
environment is that user can invoke it without physical access to the
board (without having to press the factory reset button), by running
  run bootcmd_rescue
in U-Boot's console.

Therefore we have to ensure that bootcmd_rescue is always set to default
value, regardless of whether the factory reset button was pressed.
Otherwise the variable will be empty for example after upgrade from
previous U-Boot.

Fixes: ec3784d6 ("arm: mvebu: turris_mox: add support for board rescue mode")
Fixes: 176c3e77 ("arm: mvebu: turris_omnia: support invoking rescue boot from console")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>

Xilinx changes for v2021.07-rc5

zynqmp:
- Fix ANALOG_BUS value after powerup
- Disable EFI_CAPSULE_ON_DISK_EARLY

zynqmp-gqspi:
- Fix write issue

Sata/scsi and usb based devices are not started at this stage that's why
disks are not found and early update can't happen.
It is because of deficiency in the UEFI implementation which is not able to
deal with block devices which are added or removed after initialization.

EFI capsule on disk early feature needs to be fixed first to be able to
enable this feature properly.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Enable manual start in zynqmp_qspi_fill_gen_fifo().
Also enable GQSPI_IXR_GFNFULL_MASK and check for it instead of
GQSPI_IXR_GFEMTY_MASK.

Add dummy write to genfifo register in chipselect.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>

The default register configuration after powerup for PSSYSMON_ANALOG_BUS
register is incorrect. Hence, fix this in SPL by writing correct fixed
value. It follows UG1085 chapter 'PS SYSMON Analog_Bus' and reflects commit
sw_apps:zynq ("056ca65d44549ce27f716d423e8dfdefeee7440c")
in Xilinx:embeddedsw[1].

[1] https://github.com/Xilinx/embeddedsw



Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

- mvebu: Turris MOX misc updates (cmds, rescue mode, LED's etc)
  (Marek)
- mvebu: correct Armada 8K addresses (Heinrich)

Heinrich Schuchardt authored 3 years ago and Stefan Roese committed 3 years ago

0x04000000- 0x06000000 is reserved memory. We cannot load to anything here.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Stefan Roese <sr@denx.de>

Marek Behún authored 3 years ago and Stefan Roese committed 3 years ago

Enable configuration options to support Turris network boot. This
includes FIT support and some crypto commands.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>

Marek Behún authored 3 years ago and Stefan Roese committed 3 years ago

Add nodes for SPI NOR partitions to the device tree of Turris MOX, as
are in Linux' device tree.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>

Marek Behún authored 3 years ago and Stefan Roese committed 3 years ago

Add default fdtfile environment variable with value
marvell/armada-3720-turris-mox.dtb.

This can be useful for some boot scenarios.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>

Marek Behún authored 3 years ago and Stefan Roese committed 3 years ago

Configure blinking on ethernet PHY LEDs on the MOX A board when entering
rescue mode via reset button.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>

Marek Behún authored 3 years ago and Stefan Roese committed 3 years ago

Add necessary config options and board code to support board factory
reset / rescue mode on Turris MOX.

In order to also support invoking rescue mode from U-Boot console,
without having to press the factory reset button, put the rescue command
into `bootcmd_rescue` default environment variable. When factory reset
button is pressed, invoke rescue mode via distroboot by setting
`boot_targets` to `rescue`.

Rescue boot from console can be invoked by running
  run bootcmd_rescue

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>

Marek Behún authored 3 years ago and Stefan Roese committed 3 years ago

Add nodes for indicator LED and reset button so that board code can
implement board factory reset mechanism.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>

Joao Marcos Costa authored 3 years ago and Tom Rini committed 3 years ago

The fragmented files were not correctly read because of two issues:

- The squashfs_file_info struct has a field named 'comp', which tells if
the file's fragment is compressed or not. This field was always set to
'true' in sqfs_get_regfile_info and sqfs_get_lregfile_info. It should
actually take sqfs_frag_lookup's return value. This patch addresses
these two assignments.

- In sqfs_read, the fragments (compressed or not) were copied to the
output buffer through a for loop which was reading data at the wrong
offset. Replace these loops by equivalent calls to memcpy, with the
right parameters.

I tested this patch by comparing the MD5 checksum of a few fragmented
files with the respective md5sum output in sandbox, considering both
compressed and uncompressed fragments.

Signed-off-by: Joao Marcos Costa <jmcosta944@gmail.com>
Tested-by: Richard Genoud <richard.genoud@posteo.net>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>

- dwc2 and cdns3 fixes

Pull request for efi-2021-07-rc5

Documentation:

* pinmux and ums man-page

Bug fixes:

* Consider that partition numbers as hexadecimal.
* Avoid a possible NULL dereference in efi_capsule_delete_file().

Fabio Estevam authored 3 years ago and Stefano Babic committed 3 years ago

Add support for Storopack's SMEGW01 board, which is an
IoT gateway based on the i.MX7D SoC.

Based on the original U-Boot work done by Phytec.

Signed-off-by: Fabio Estevam <festevam@denx.de>

Andrey Zhizhikin authored 3 years ago and Stefano Babic committed 3 years ago

Supported boot device types in iMX8MN: MMC, DHCP.

Add DISTRO_DEFAULTS config option and include the distro boot command
header file to enable full support of distro boot on i.MX8M Nano EVK (both
DDR and LPDDR derivatives).

Drop previous environment, which was targeting customized boot commands and
boot order.

Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>

Navin Sankar Velliangiri authored 3 years ago and Stefano Babic committed 3 years ago

CPU:   Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz)
CPU:   Industrial temperature grade (-40C to 105C) at 49C
Reset cause: POR
Model: Seeed NPi iMX6ULL Dev Board with NAND
Board: Seeed NPi i.MX6ULL Dev Board
DRAM:  512 MiB
NAND:  512 MiB
MMC:   FSL_SDHC: 0
In:    serial@2020000
Out:   serial@2020000
Err:   serial@2020000
Net:   FEC0

Working:
- Eth0
- MMC/SD
- NAND
- UART 1
- USB host

Signed-off-by: Navin Sankar Velliangiri <navin@linumiz.com>

Note:

Changes in v2:

 * removed unnecessary space in imx6ull-seeed-npi-imx6ull-dev-board.dts file.
 * Used SZ_2M for CONFIG_SYS_MALLOC_LEN size allocation.

Oliver Graute authored 3 years ago and Stefano Babic committed 3 years ago

Add i.MX8QM qmx8 congatec board support

U-Boot 2021.07-rc3-00528-gc9a966d9dd (May 31 2021 - 15:21:25 +0200)

CPU:   NXP i.MX8QM RevB A53 at 1200 MHz

Model: Congatec QMX8 Qseven series
Board: conga-QMX8
Build: SCFW 494c97f3, SECO-FW d63fdb21, ATF 09c5cc9
Boot:  SD2
DRAM:  6 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In:    serial@5a060000
Out:   serial@5a060000
Err:   serial@5a060000
switch to partitions #0, OK
mmc2 is current device
Net:
Error: ethernet@5b040000 address not set.
No ethernet found.

Hit any key to stop autoboot:  0

Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>

Andrey Zhizhikin authored 3 years ago and Stefano Babic committed 3 years ago

Frequency requested by ddrphy_init_set_dfi_clk from fracpll uses MHZ()
macro, which expands the value provided to the Hz range without taking into
account the precise Hz setting. This causes the frequency of 266 MHz not ot
be found in the imx8mm_fracpll_tbl, since it is entered there with a
precise Hz value. This in turn causes the boot hang in SPL, as proper DDR
fracpll frequency cannot be determined.

Correct the value in imx8mm_fracpll_tbl to match the one expanded by
MHZ(266) macro, rounding it down to MHz range only.

Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ye Li <ye.li@nxp.com>
Fixes: 825ab6b4 ("driver: ddr: Refine the ddr init driver on imx8m")
Reviewed-by: Fabio Estevam <festevam@gmail.com>

Fabio Estevam authored 3 years ago and Stefano Babic committed 3 years ago

The original URL that explains the boot mode setting is no longer
valid.

Update to the new one.

Signed-off-by: Fabio Estevam <festevam@gmail.com>

Tim Harvey authored 3 years ago and Stefano Babic committed 3 years ago

Enable driver model support for FEC ethernet which allows us to remove
the iomux and board_eth_init function. Replace the toggling of the ethernet
phy reset with dt configuration.

Enable driver model support for PCI which allows us to remove the
eth1000_initialize() call. Additionally enable PCI_INIT_R to scan for
PCI devices on init such as the e1000 that is present on the GW552x.

Convert board_pci_fixup to use dm callback and remove pcidisable env
variable which is not supported for DM_PCI and thus leave PCI always
enabled during init.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>

Andrey Zhizhikin authored 3 years ago and Stefano Babic committed 3 years ago

Clock initialization functionality has ambitious debug messages, which are
printed out when failures are triggered during execution:
- Separate frequency table lookup functions have the the same output that
  makes it impossible to understand which function failed and produced the
  output
- PLL decoding routine has a generic debug statement printed, which does
  not state the actual value failed to be found

Extend the output for both cases with prefixing table lookup functions
output with function name, and report the failed value in PLL decoding
routine.

Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>

Oleh Kravchenko authored 3 years ago and Stefano Babic committed 3 years ago

A simple prototyping board with one microSD port, one Ethernet port,
2 USB ports, I2C, SPI, GPIO, and UART interfaces.

Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Cc: Stefano Babic <sbabic@denx.de>

Oleh Kravchenko authored 3 years ago and Stefano Babic committed 3 years ago

Board designed for quick prototyping and has one microSD port,
2 Ethernet ports, 2 USB ports, I2C, SPI, CAN, RS-485, GPIO,
UART interfaces, and 2 RGB LEDs.

Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Cc: Stefano Babic <sbabic@denx.de>

Marek Vasut authored 3 years ago and Stefano Babic committed 3 years ago

Uncompressed aarch64 kernel Image are rather large, increase the bootm
size limit to 64 MiB to cater for that.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>

Giulio Benetti authored 3 years ago and Stefano Babic committed 3 years ago

Now that usb host is supported let's enable it on this board.

Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>

Giulio Benetti authored 3 years ago and Stefano Babic committed 3 years ago

Enable usbotg1 port node as host usb.

Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>

Giulio Benetti authored 3 years ago and Stefano Babic committed 3 years ago

Usb is now supported so add all required nodes for it in imxrt1050.

Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>