- Sep 15, 2020
-
-
Enable HyperBus and HyperFlash to support HyperFlash boot. Signed-off-by:Vignesh Raghavendra <vigneshr@ti.com>
-
On J7200 SoC OSPI and HypeFlash are muxed at HW level and only one of them can be used at any time. J7200 EVM has both HyperFlash and OSPI flash on board. There is a user switch (SW3.1) that can be toggled to select OSPI flash vs HyperFlash. Read the state of this switch via wkup_gpio0_6 line and fixup the DT nodes to select OSPI vs HyperFlash Signed-off-by: -
HBMC controller on TI K3 SoC provides MMIO access to HyperFlash similar to legacy Parallel CFI NOR flashes. Therefore alias HyperFlash bootmode to NOR boot to enable SPL to load next stage using NOR boot flow. Signed-off-by:
-
- Sep 07, 2020
-
-
Tom Rini authored
Signed-off-by:Tom Rini <trini@konsulko.com>
-
Tom Rini authored
Rsync all defconfig files using moveconfig.py Signed-off-by: -
https://gitlab.denx.de/u-boot/custodians/u-boot-efiTom Rini authored
Pull request for UEFI sub-system for efi-2020-10-rc4 Bug fixes are provided in the following areas: * convert file system debug and print messages go log messages * convert UEFI booting messages to log messages * UEFI related code clean up and simplification
-
- Sep 06, 2020
-
-
Heinrich Schuchardt authored
CONFIG_EFI_LOADER cannot be selected for ARMv7-M CPUs. So don't check it in the Makefile. Signed-off-by:Heinrich Schuchardt <xypron.glpk@gmx.de>
-
Heinrich Schuchardt authored
The image size is checked in efi_load_pe(). Avoid checking it twice. Signed-off-by: -
Heinrich Schuchardt authored
* Eliminate superfluous enum value EFI_TABLE_END. * Use correct variable type for the memory type. * Check validity of memory type. * Make efi_build_mem_table static. Signed-off-by: -
Heinrich Schuchardt authored
Currently if the bootefi command fails due to missing authentication, the user gets no feedback. Write a log message 'Image not authenticated' if LoadImage() fails due to missing authentication. Signed-off-by: -
Heinrich Schuchardt authored
Use log_err() for error messages. Replace debug() by EFI_PRINT(). Signed-off-by: -
Heinrich Schuchardt authored
Write log messages when booting via the bootefi command to allow tracking on the syslog server. Example messages are Booting /snp.efi or Booting /MemoryMapped(0x0,0x4fe00000,0x35a40) Loading image failed Signed-off-by: -
Heinrich Schuchardt authored
Use log functions for error and debug messages of the file-system. Signed-off-by:
Simon Glass <sjg@chromium.org>
-
- Sep 04, 2020
-
-
https://gitlab.denx.de/u-boot/custodians/u-boot-marvellTom Rini authored
- Fix SATA issue on Armada 3720 - Enable more SPI NOR chips in espressobin defconfig
-
Enable support of ISSI SPI flashes found on EspressoBIN boards Change-Id: I6de61c48f108fb4f410f321b9db45887d23212e5 Signed-off-by:
Konstantin Porotchkin <kostap@marvell.com> Reviewed-on: http://vgitil04.il.marvell.com:8080/61455 Tested-by:
iSoC Platform CI <ykjenk@marvell.com> Reviewed-by:
Grzegorz Jaszczyk <jaz@semihalf.com> Reviewed-by:
Stefan Chulski <stefanc@marvell.com> Reviewed-by:
Stefan Roese <sr@denx.de>
-
Include support for CONFIG_SPI_FLASH_GIGADEVICE for supporting newly produces EspressoBin boards (v7) Change-Id: I5d4b972cbe2ee5a9d52ce9908794ad4e1b59ee3b Signed-off-by:
Igal Liberman <igall@marvell.com> Reviewed-by:
-
- This patch moves sata phy powerup from dedicate phy to compphy and adds invert option for sata powerup routine. Change-Id: I1b4e8753e2b2c14c6efa97bca2ffc7d2553d8a90 Signed-off-by:
zachary <zhangzg@marvell.com> Signed-off-by:
Ken Ma <make@marvell.com> Reviewed-on: http://vgitil04.il.marvell.com:8080/53601 Reviewed-by:
Andre Heider <a.heider@gmail.com> Tested-by:
Pali Rohár <pali@kernel.org> Reviewed-by:
-
- Sep 03, 2020
-
-
-
-
-
Chee Hong Ang authored
Instead of querying SDM for FPGA configuration status through mailbox messages, U-Boot now checks System Manager's FPGA Config status register for FPGA configuration status before resetting bridge. Signed-off-by:
Chee Hong Ang <chee.hong.ang@intel.com> Reviewed-by:
Ley Foon Tan <ley.foon.tan@intel.com>
-
- Sep 02, 2020
-
-
Tom Rini authored
- New base snapshot - Fix for high UID/GID numbers on a toolchain Signed-off-by:
-
- Sep 01, 2020
-
-
https://gitlab.denx.de/u-boot/custodians/u-boot-x86Tom Rini authored
- Fix parsing of "mtrr list" command - Introduce USE_EARLY_BOARD_INIT option and remove dead codes for most x86 boards
-
The size returned by 'getvar partition-size' should be in bytes, not in blocks as fastboot uses that value to generate empty partition when running format [1]. Note that the function was already returning the proper size in bytes for NAND devices (see struct part_info details). [1] https://android.googlesource.com/platform/system/core/+/refs/heads/android10-release/fastboot/fastboot.cpp#1500 Signed-off-by:
Gary Bisson <gary.bisson@boundarydevices.com>
-
It was revealed that when the fastboot_tx_write_str function is called without the previously initialized fastboot_func->in_req->complete field, a copy of in_req will be sent to the I/O requests queue without an initialized field. Moving a piece of code with the initializing of the fastboot_func->in_req->complete field above transmit_tx allows to solve this problem. Fixes: 65c96757 "usb: fastboot: Convert USB f_fastboot to shared fastboot" Signed-off-by:
yurii.pidhornyi <yurii.pidhornyi@globallogic.com>
-
Since the USB HID limits the maximum bandwidth(3072) for interrupt endpoint transfers, when the bInterval set to 1, we can only support 3 boards to run sdp at the same time. In order to support more boards, change the bInterval of interrupt endpoint to 3, which will not affect the transmission speed. Reviewed-by:
Ye Li <ye.li@nxp.com> Signed-off-by:
Sherry Sun <sherry.sun@nxp.com> Signed-off-by:
Peng Fan <peng.fan@nxp.com>
-
EP0 has been used to transfer file data in sdp before, but the max packetsize of ep0 is 64 bytes. So in order to improve the file transfer speed, here add the EP1_OUT interrupt endpoint which max packetsize is set to 1024 byte. After testing, it turns out that using ep1out is twice as fast as using ep0 while receiving data in sdp. Signed-off-by:
-
Add g_dnl_get_board_bcd_device_number, the new BCD value is used by uuu to distinguish if the SPL supports the SDPV. Signed-off-by:
Lukasz Majewski <lukma@denx.de>
-
Add support to f_sdp to search and load iMX8 container image or iMX8M FIT image by new UUU command SDPV. When using the SDPV, the uuu will continue to send out data after first level boot loader used by ROM. This means uuu won't skip to the offset of the second boot loader, and the padding data before second boot loader will be sent out. So we have to search the FIT header or container header in the buffer that SDP received. Also change to more common method to exit f_sdp handler not depending on SPL_FIT_FOUND flag because container loader won't set this. Signed-off-by: -
Because the buffer length of sdp usb request is 65, we have to allocate 65 bytes not 64 bytes. Otherwise there is potential buffer overflow. Signed-off-by:
-
Add HS endpoint descriptor for SDP. So that we can use high speed endpoint, and the SDP device can send packet with 512 byte size. Signed-off-by:
-
Need initialize UDC before run sdp download Signed-off-by:
Frank Li <Frank.Li@nxp.com> Signed-off-by:
-
MAX3420 implements FullSpeed USB Device over SPI. Another version MAX3421, also implements USB Host mode. This driver should be good for the device mode of max3421 as well. Signed-off-by:Jassi Brar <jaswinder.singh@linaro.org>
-
Default implementation of fastboot_set_reboot_flag function that depends on "bcb" commands could be used in general case if there are no need to make any platform-specific implementation, otherwise it could be disabled via Kconfig option FASTBOOT_USE_BCB_SET_REBOOT_FLAG. Please note that FASTBOOT_USE_BCB_SET_REBOOT_FLAG is mutually exclusive with some platforms which already have their own implementation of this function. Signed-off-by:Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
-
Android 10 adds support for dynamic partitions and in order to support this userspace fastboot must be used[1]. New tool fastbootd is included into recovery. Userspace fastboot works from recovery and is launched if: 1) - Dynamic partitioning is enabled 2) - Boot control block has 'boot-fastboot' value into command field The bootloader is expected to load and boot into the recovery image upon seeing boot-fastboot in the BCB command. Recovery then parses the BCB message and switches to fastbootd mode[2]. Please note that boot script is expected to handle 'boot-fastboot' command in BCB and load into recovery mode. Bootloader must support 'reboot fastboot' command which should reboot device into userspace fastboot to accomodate those changes[3]. Another command that bootloader must support[3] is 'reboot recovery'. This command should simply reboot device into recovery mode. [1] - https://source.android.com/devices/bootloader/fastbootd [2] - https://source.android.com/devices/bootloader/fastbootd#unified_fastboot_and_recovery [3] - https://source.android.com/devices/bootloader/fastbootd#modifications_to_the_bootloader Signed-off-by:
Roman Stratiienko <r.stratiienko@gmail.com> Change-Id: I9d2bdc9a6f6f31ea98572fe155e1cc8341e9af76
-
Extend fastboot_set_reboot_flag arguments with reboot reason so that it could handle different reboot cases in future. Signed-off-by: -
The environment variable loadaddr is in the virtual address space of the sandbox. To get the actual memory address where the FIT image has been loaded we have to convert this address according to the memory mapping of the sandbox. Equally the addresses in the *.its file have to be converted when used in the dfu_ram driver. Signed-off-by: -
For testing automated updates via dfu and mtd we need the dfu and mtd commands as well as preboot support. Signed-off-by: -
Function mtdparts_init() is needed for the DFU MTD driver. Signed-off-by: -
%s/parameteres/parameters/g Even if a line exceeds 80 characters we should not split output strings to make debugging easier. Signed-off-by:
-
