Aleksandar Gerasimovski authored 3 years ago and Priyanka Jain committed 3 years ago

This patch adds the front led initialization and the application
buffer enable to the eraly board inititlaization.

Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Aleksandar Gerasimovski authored 3 years ago and Priyanka Jain committed 3 years ago

In order to improve power consumption ls102x allows to disable peripherals
that are not in use.
This patch follows SELI8 HW design description and disables peripherals
that are not in use in our designs, the same configuration is applicable
and for EXPU1.

This patch uses available hwconfig option for updating ls102x device
disable configuration.

Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Aleksandar Gerasimovski authored 3 years ago and Priyanka Jain committed 3 years ago

The default behavior in the latest u-boot revisions is to rotate the
active net device to the next available if the requested link is not
established.

For our ls102x based devices this would mean that if active debug net
device is not available, u-boot will rotate and set the next net device
that is one of the estar adapters.
To return from this situation manual action to set correct ethact
adapter will be needed and this can be annoying when working in
debug mode.

Setting ethrotate=no will disable net adapter rotation and will make sure
that the primary adapter is always used.

Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Aleksandar Gerasimovski authored 3 years ago and Priyanka Jain committed 3 years ago

This is most probably a typo, and in older u-uboot versions is same as
'saveenv', in the newer uboot versions there is a separate 'save' command
that is different from 'saveenv'.

Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Aleksandar Gerasimovski authored 3 years ago and Priyanka Jain committed 3 years ago

In our designs we reserve PRAM area at the end of the RAM, and in order
this area to be visible and taken into account by the u-boot memory mgmt
CONFIG_PRAM has to be defined.

Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Aleksandar Gerasimovski authored 3 years ago and Priyanka Jain committed 3 years ago

From production view this is standard test executed during production on
all linux based foxmc cards.
On CENT2 HW defined memory region is zero means that some DDR accesses are
done by memory_post_dataline and memory_post_addrline but pattern tests
are skipped that's why mem_regions is fast there.

On ls102x for the complete DDR region of 1GiB memory_regions_post_test
takes approx. 4min and this is too much for production, so this patch
defines only 1MiB region as compromise.

Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Aleksandar Gerasimovski authored 3 years ago and Priyanka Jain committed 3 years ago

The EXPU1 design is a new 40G capable ethernet service unit card for
Hitachi-Powergrids wired-com product lines.

The base SoC is same as for already added SELI8 card, consequently the
already added u-boot support for SELI8 is reused.

Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
[Fixed new line error at EOF]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>

Add "Priyanka Jain <priyanka.jain@nxp.com>" as
MAINTAINER for t102xrdb board.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>

Add "Priyanka Jain <priyanka.jain@nxp.com>" as
MAINTAINER for p2041rdb board.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>

Add "Priyanka Jain <priyanka.jain@nxp.com>" as
MAINTAINER for p1_p2_rdb_pc board.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>

Add "Priyanka Jain <priyanka.jain@nxp.com>" as
MAINTAINER for t4rdb board.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>

Lasse Klok Mikkelsen authored 3 years ago and Priyanka Jain committed 3 years ago

Address and size cells on SOC are set to 1. But gpio nodes are specified
with 2 cells. This fixes the gpio nodes to correct cells.

Signed-off-by: Lasse Klok Mikkelsen <lkmi@prevas.dk>
Reviewed-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Aleksandar Gerasimovski authored 3 years ago and Priyanka Jain committed 3 years ago

Current tsec adapter sets adapter gigabit capabilities by default, and in
reality this must not always be the case.
It is possible that tsec adapter is used for 100Mbps connection, and in
this case setting 1000Mbps capabilities can lead to some side effects such
longer autoneg process.

In our ls102x designs this problem leads to long autoneg times (> 4 sec)
in case board rgmii link is 100Mbps capable only.
Limiting the rgmii link capabilities provides faster and smoother
link establishment.

Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Aleksandar Gerasimovski authored 3 years ago and Priyanka Jain committed 3 years ago

Commit df86d324 breaks linux kernel and product application boot.

Linux kernel and our product application scripts are expecting 0x prefix
for hexadecimal values, while env_set_hex writes them without a prefix.

This patch partially revert env_set_hex usage for affected env variables.

Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Aleksandar Gerasimovski authored 3 years ago and Priyanka Jain committed 3 years ago

During the mainlining of the board this was by mistake set to sector size.
Our user space env scripts are expecting envsize of 0x4000, and setting
this differently will break our cross-platform compatibility.

Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Yangbo Lu authored 3 years ago and Priyanka Jain committed 3 years ago

Drop CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33. CONFIG_FSL_ESDHC_VS33_NOT_SUPPORT
is used instead.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Michael Walle <michael@walle.cc> [for kontron-sl28]
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Yangbo Lu authored 3 years ago and Priyanka Jain committed 3 years ago

There is no i.MX board using such option. Drop it.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Yangbo Lu authored 3 years ago and Priyanka Jain committed 3 years ago

For eSDHC, power supply is through peripheral circuit.
Some eSDHC versions have value 0 of the bit but that
does not reflect the truth. 3.3V is common for SD/MMC,
and is supported for all boards with eSDHC in current
u-boot. So, make 3.3V is supported in default in code.
CONFIG_FSL_ESDHC_VS33_NOT_SUPPORT can be enabled if
future board does not support 3.3V.

This is also a fix-up for one previous patch, which converted
to use IS_ENABLED() for CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
that is not a Kconfig option.

Fixes: 52faec31 ("mmc: fsl_esdhc: replace most #ifdefs by IS_ENABLED()")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Matt Merhar authored 3 years ago and Priyanka Jain committed 3 years ago

These boards, according to the schematic and per the board I own, use an
M24256-BWDW6TP I2C EEPROM which requires two address bytes.

This fixes the 'mac' command which is used to program, among other
things, the MAC addresses for the ethernet interfaces on the board.

Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Biwen Li authored 3 years ago and Priyanka Jain committed 3 years ago

IFC NOR flash base address of ls2088a is 0x580000000,
and offset of env crc is 0x500000, so fix the macro
CONFIG_ENV_ADDR to fix synchronous exception(access illegal address)

Fixes: 59071804 ("configs: ls2080a: Correct ENV_ADDR value")
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Kuldeep Singh authored 3 years ago and Priyanka Jain committed 3 years ago

Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Yangbo Lu authored 3 years ago and Priyanka Jain committed 3 years ago

Add properties related to eMMC HS400 mode for esdhc1.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Hou Zhiqiang authored 3 years ago and Priyanka Jain committed 3 years ago

Stop to initialize the PCIe controller if it's disabled by RCW.

Fixes: 118e58e2 ("pci: layerscape: Split the EP and RC driver")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Chaitanya Sakinam authored 3 years ago and Priyanka Jain committed 3 years ago

Read Linux PPFE firmware from flash partition and pass it to Linux through
FDT entry. So that we can avoid placing PPFE firmware in Linux rootfs.
(FDT may increase at max by 64KB)

Signed-off-by: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
Signed-off-by: Anji J <anji.jagarlmudi@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Yangbo Lu authored 3 years ago and Priyanka Jain committed 3 years ago

Enable eMMC HS400 workarounds for LX2160A/LX2162A.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Jiafei Pan authored 3 years ago and Priyanka Jain committed 3 years ago

For cpu release command, check whether PSCI is supported firstly,
if supported, use PSCI to kick off secondary cores, otherwise still
use spin table.

Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
[Fixed checkpatch alignment CHECKs]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>

Priyanka Singh authored 3 years ago and Priyanka Jain committed 3 years ago

Add check for return value of adjust_vdd()

Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Mian Yousaf Kaukab authored 3 years ago and Priyanka Jain committed 3 years ago

When using bootefi to boot a EFI binary, u-boot is supposed to
provide networking service for EFI application. Currently, 'pfe stop'
command is called from bootcmd before running bootefi. As a result
network stops working for EFI applications and console is flooded with
"Rx pkt not on expected port" messages.

Implement board_quiesce_devices() for ls1012a boards and call
pfe_command_stop() from it instead of calling 'pfe stop' from
*_bootcmd and bootcmd.

Tested-by: Anji Jagarlmudi <anji.jagarlmudi@nxp.com>
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
[Fixed checkpatch space error]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>

Michael Walle authored 3 years ago and Priyanka Jain committed 3 years ago

It was noticed that the clock isn't continuously enabled when there is
no link. This is because the 125MHz clock is derived from the internal
PLL which seems to go into some kind of power-down mode every once in a
while. The LS1028A expects a contiuous clock. Thus enable the PLL all
the time.

Also, the RGMII pad voltage is wrong, it was configured to 2.5V (that is
the VDDH regulator). The correct voltage is 1.8V, i.e. the VDDIO
regulator.

Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Manish Tomar authored 3 years ago and Priyanka Jain committed 3 years ago

Add required CONFIG_NXP_ESBC for ls1046afrwy to enable ESBC Chain of Trust.

Signed-off-by: Manish Tomar <manish.tomar@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

- Turris: Fix bootcmd_rescue (Pali)

Pali Rohár authored 3 years ago and Stefan Roese committed 3 years ago

One of the points of putting the rescue boot command into default
environment is that user can invoke it without physical access to the
board (without having to press the factory reset button), by running
  run bootcmd_rescue
in U-Boot's console.

Therefore we have to ensure that bootcmd_rescue is always set to default
value, regardless of whether the factory reset button was pressed.
Otherwise the variable will be empty for example after upgrade from
previous U-Boot.

Fixes: ec3784d6 ("arm: mvebu: turris_mox: add support for board rescue mode")
Fixes: 176c3e77 ("arm: mvebu: turris_omnia: support invoking rescue boot from console")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>

Xilinx changes for v2021.07-rc5

zynqmp:
- Fix ANALOG_BUS value after powerup
- Disable EFI_CAPSULE_ON_DISK_EARLY

zynqmp-gqspi:
- Fix write issue

Sata/scsi and usb based devices are not started at this stage that's why
disks are not found and early update can't happen.
It is because of deficiency in the UEFI implementation which is not able to
deal with block devices which are added or removed after initialization.

EFI capsule on disk early feature needs to be fixed first to be able to
enable this feature properly.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Enable manual start in zynqmp_qspi_fill_gen_fifo().
Also enable GQSPI_IXR_GFNFULL_MASK and check for it instead of
GQSPI_IXR_GFEMTY_MASK.

Add dummy write to genfifo register in chipselect.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>

The default register configuration after powerup for PSSYSMON_ANALOG_BUS
register is incorrect. Hence, fix this in SPL by writing correct fixed
value. It follows UG1085 chapter 'PS SYSMON Analog_Bus' and reflects commit
sw_apps:zynq ("056ca65d44549ce27f716d423e8dfdefeee7440c")
in Xilinx:embeddedsw[1].

[1] https://github.com/Xilinx/embeddedsw



Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

- mvebu: Turris MOX misc updates (cmds, rescue mode, LED's etc)
  (Marek)
- mvebu: correct Armada 8K addresses (Heinrich)

Heinrich Schuchardt authored 3 years ago and Stefan Roese committed 3 years ago

0x04000000- 0x06000000 is reserved memory. We cannot load to anything here.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Stefan Roese <sr@denx.de>

Marek Behún authored 3 years ago and Stefan Roese committed 3 years ago

Enable configuration options to support Turris network boot. This
includes FIT support and some crypto commands.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>

Marek Behún authored 3 years ago and Stefan Roese committed 3 years ago

Add nodes for SPI NOR partitions to the device tree of Turris MOX, as
are in Linux' device tree.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>