Yangbo Lu authored 3 years ago and Priyanka Jain committed 3 years ago

For eSDHC, power supply is through peripheral circuit.
Some eSDHC versions have value 0 of the bit but that
does not reflect the truth. 3.3V is common for SD/MMC,
and is supported for all boards with eSDHC in current
u-boot. So, make 3.3V is supported in default in code.
CONFIG_FSL_ESDHC_VS33_NOT_SUPPORT can be enabled if
future board does not support 3.3V.

This is also a fix-up for one previous patch, which converted
to use IS_ENABLED() for CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
that is not a Kconfig option.

Fixes: 52faec31 ("mmc: fsl_esdhc: replace most #ifdefs by IS_ENABLED()")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Matt Merhar authored 3 years ago and Priyanka Jain committed 3 years ago

These boards, according to the schematic and per the board I own, use an
M24256-BWDW6TP I2C EEPROM which requires two address bytes.

This fixes the 'mac' command which is used to program, among other
things, the MAC addresses for the ethernet interfaces on the board.

Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Biwen Li authored 3 years ago and Priyanka Jain committed 3 years ago

IFC NOR flash base address of ls2088a is 0x580000000,
and offset of env crc is 0x500000, so fix the macro
CONFIG_ENV_ADDR to fix synchronous exception(access illegal address)

Fixes: 59071804 ("configs: ls2080a: Correct ENV_ADDR value")
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Kuldeep Singh authored 3 years ago and Priyanka Jain committed 3 years ago

Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Yangbo Lu authored 3 years ago and Priyanka Jain committed 3 years ago

Add properties related to eMMC HS400 mode for esdhc1.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Hou Zhiqiang authored 3 years ago and Priyanka Jain committed 3 years ago

Stop to initialize the PCIe controller if it's disabled by RCW.

Fixes: 118e58e2 ("pci: layerscape: Split the EP and RC driver")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Chaitanya Sakinam authored 3 years ago and Priyanka Jain committed 3 years ago

Read Linux PPFE firmware from flash partition and pass it to Linux through
FDT entry. So that we can avoid placing PPFE firmware in Linux rootfs.
(FDT may increase at max by 64KB)

Signed-off-by: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
Signed-off-by: Anji J <anji.jagarlmudi@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Yangbo Lu authored 3 years ago and Priyanka Jain committed 3 years ago

Enable eMMC HS400 workarounds for LX2160A/LX2162A.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Jiafei Pan authored 3 years ago and Priyanka Jain committed 3 years ago

For cpu release command, check whether PSCI is supported firstly,
if supported, use PSCI to kick off secondary cores, otherwise still
use spin table.

Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
[Fixed checkpatch alignment CHECKs]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>

Priyanka Singh authored 3 years ago and Priyanka Jain committed 3 years ago

Add check for return value of adjust_vdd()

Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Mian Yousaf Kaukab authored 3 years ago and Priyanka Jain committed 3 years ago

When using bootefi to boot a EFI binary, u-boot is supposed to
provide networking service for EFI application. Currently, 'pfe stop'
command is called from bootcmd before running bootefi. As a result
network stops working for EFI applications and console is flooded with
"Rx pkt not on expected port" messages.

Implement board_quiesce_devices() for ls1012a boards and call
pfe_command_stop() from it instead of calling 'pfe stop' from
*_bootcmd and bootcmd.

Tested-by: Anji Jagarlmudi <anji.jagarlmudi@nxp.com>
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
[Fixed checkpatch space error]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>

Michael Walle authored 3 years ago and Priyanka Jain committed 3 years ago

It was noticed that the clock isn't continuously enabled when there is
no link. This is because the 125MHz clock is derived from the internal
PLL which seems to go into some kind of power-down mode every once in a
while. The LS1028A expects a contiuous clock. Thus enable the PLL all
the time.

Also, the RGMII pad voltage is wrong, it was configured to 2.5V (that is
the VDDH regulator). The correct voltage is 1.8V, i.e. the VDDIO
regulator.

Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

Manish Tomar authored 3 years ago and Priyanka Jain committed 3 years ago

Add required CONFIG_NXP_ESBC for ls1046afrwy to enable ESBC Chain of Trust.

Signed-off-by: Manish Tomar <manish.tomar@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

- Turris: Fix bootcmd_rescue (Pali)

Pali Rohár authored 3 years ago and Stefan Roese committed 3 years ago

One of the points of putting the rescue boot command into default
environment is that user can invoke it without physical access to the
board (without having to press the factory reset button), by running
  run bootcmd_rescue
in U-Boot's console.

Therefore we have to ensure that bootcmd_rescue is always set to default
value, regardless of whether the factory reset button was pressed.
Otherwise the variable will be empty for example after upgrade from
previous U-Boot.

Fixes: ec3784d6 ("arm: mvebu: turris_mox: add support for board rescue mode")
Fixes: 176c3e77 ("arm: mvebu: turris_omnia: support invoking rescue boot from console")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>

Xilinx changes for v2021.07-rc5

zynqmp:
- Fix ANALOG_BUS value after powerup
- Disable EFI_CAPSULE_ON_DISK_EARLY

zynqmp-gqspi:
- Fix write issue

Sata/scsi and usb based devices are not started at this stage that's why
disks are not found and early update can't happen.
It is because of deficiency in the UEFI implementation which is not able to
deal with block devices which are added or removed after initialization.

EFI capsule on disk early feature needs to be fixed first to be able to
enable this feature properly.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Enable manual start in zynqmp_qspi_fill_gen_fifo().
Also enable GQSPI_IXR_GFNFULL_MASK and check for it instead of
GQSPI_IXR_GFEMTY_MASK.

Add dummy write to genfifo register in chipselect.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>

The default register configuration after powerup for PSSYSMON_ANALOG_BUS
register is incorrect. Hence, fix this in SPL by writing correct fixed
value. It follows UG1085 chapter 'PS SYSMON Analog_Bus' and reflects commit
sw_apps:zynq ("056ca65d44549ce27f716d423e8dfdefeee7440c")
in Xilinx:embeddedsw[1].

[1] https://github.com/Xilinx/embeddedsw



Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

- mvebu: Turris MOX misc updates (cmds, rescue mode, LED's etc)
  (Marek)
- mvebu: correct Armada 8K addresses (Heinrich)

Heinrich Schuchardt authored 3 years ago and Stefan Roese committed 3 years ago

0x04000000- 0x06000000 is reserved memory. We cannot load to anything here.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Stefan Roese <sr@denx.de>

Marek Behún authored 3 years ago and Stefan Roese committed 3 years ago

Enable configuration options to support Turris network boot. This
includes FIT support and some crypto commands.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>

Marek Behún authored 3 years ago and Stefan Roese committed 3 years ago

Add nodes for SPI NOR partitions to the device tree of Turris MOX, as
are in Linux' device tree.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>

Marek Behún authored 3 years ago and Stefan Roese committed 3 years ago

Add default fdtfile environment variable with value
marvell/armada-3720-turris-mox.dtb.

This can be useful for some boot scenarios.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>

Marek Behún authored 3 years ago and Stefan Roese committed 3 years ago

Configure blinking on ethernet PHY LEDs on the MOX A board when entering
rescue mode via reset button.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>

Marek Behún authored 3 years ago and Stefan Roese committed 3 years ago

Add necessary config options and board code to support board factory
reset / rescue mode on Turris MOX.

In order to also support invoking rescue mode from U-Boot console,
without having to press the factory reset button, put the rescue command
into `bootcmd_rescue` default environment variable. When factory reset
button is pressed, invoke rescue mode via distroboot by setting
`boot_targets` to `rescue`.

Rescue boot from console can be invoked by running
  run bootcmd_rescue

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>

Marek Behún authored 3 years ago and Stefan Roese committed 3 years ago

Add nodes for indicator LED and reset button so that board code can
implement board factory reset mechanism.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>

Joao Marcos Costa authored 3 years ago and Tom Rini committed 3 years ago

The fragmented files were not correctly read because of two issues:

- The squashfs_file_info struct has a field named 'comp', which tells if
the file's fragment is compressed or not. This field was always set to
'true' in sqfs_get_regfile_info and sqfs_get_lregfile_info. It should
actually take sqfs_frag_lookup's return value. This patch addresses
these two assignments.

- In sqfs_read, the fragments (compressed or not) were copied to the
output buffer through a for loop which was reading data at the wrong
offset. Replace these loops by equivalent calls to memcpy, with the
right parameters.

I tested this patch by comparing the MD5 checksum of a few fragmented
files with the respective md5sum output in sandbox, considering both
compressed and uncompressed fragments.

Signed-off-by: Joao Marcos Costa <jmcosta944@gmail.com>
Tested-by: Richard Genoud <richard.genoud@posteo.net>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>

- dwc2 and cdns3 fixes

Pull request for efi-2021-07-rc5

Documentation:

* pinmux and ums man-page

Bug fixes:

* Consider that partition numbers as hexadecimal.
* Avoid a possible NULL dereference in efi_capsule_delete_file().

Brackets '[' need to be escaped to avoid a build warning

    lib/efi_loader/efi_image_loader.c:223:
    WARNING: Inline strong start-string without end-string.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Masahisa Kojima <masahisa.kojima@linaro.org>

João Loureiro authored 4 years ago and Marek Vasut committed 3 years ago

When `usb start` is called on the terminal, the dwc2 driver will try
to start every USB device as host first, even if it is explicitly
configured as peripheral in the device tree (dr_mode = "peripheral").

So to avoid an unwanted 15 seconds delay when initializing the usb
(one second per channel = 1s x 15), this patch adds a check to the
initialization, and will skip host initialization of the device is
explicitly set as peripheral. The checking is already done similarly
in the `drivers/usb/gadget/dwc2_udc_otg.c` driver.

Signed-off-by: João Loureiro <joaofl@gmail.com>

If opening a file fails, the file handle pointer is not valid and must not
be dereferenced.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

If we want to address partition 15 of virtio block device 11, we have to
write:

	virtio b:f

When calling sprintf() we must use %x for the device and partition numbers.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

Patrick Delaunay authored 3 years ago and Heinrich Schuchardt committed 3 years ago

Provide a man-page for the ums command - USB Mass Storage.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

Patrick Delaunay authored 3 years ago and Heinrich Schuchardt committed 3 years ago

Add the missing dependency for the command ums:
- CONFIG_BLK: call of blk_* functions in usb_mass_storage.c
- CONFIG_USB_GADGET: required to select CONFIG_USB_FUNCTION_MASS_STORAGE

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

Patrick Delaunay authored 3 years ago and Heinrich Schuchardt committed 3 years ago

Provide a man-page for the pinmux command.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>

Patrick Delaunay authored 3 years ago and Heinrich Schuchardt committed 3 years ago

Reorder alphabetically the command in the index of usage
in U-Boot documentation.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

- More pinctrl updates

Kishon Vijay Abraham I authored 3 years ago and Marek Vasut committed 3 years ago

Kernel device tree got updated to use clock name as "ref" instead of
"usb2_refclk". Fix cdns3-ti.c to use the correct name.

Fixes: 70e16749 ("arm: dts: k3-j721e: Sync Linux v5.11-rc6 dts into U-Boot")
Fixes: 6239cc8c ("arm: dts: k3-j7200: Sync Linux v5.11-rc6 dts into U-Boot")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>