- Jun 17, 2021
-
-
Priyanka Jain authored
Add Priyanka Jain as MAINTAINER for T2080RDB_revD_defconfig, T2080RDB_revD_NAND_defconfig, T2080RDB_revD_SDCARD_defconfig and T2080RDB_revD_SPIFLASH_defconfig Signed-off-by:Priyanka Jain <priyanka.jain@nxp.com>
-
Change the USB erratum number A-050106 to A-050204 as A-050106 is a duplicate and never be published. Fixes 0cfa00cd (“armv8: Add workaround for USB erratum A-050106”) Signed-off-by:
Ran Wang <ran.wang_1@nxp.com> [Rebased] Signed-off-by:
-
Under DM, we rely on u-boot's device tree to provide the correct PHY addresses. The board_fix_fdt callback is intended to be used for device tree fixups before relocation. Unfortunately, this isn't an option when booting from flash since the device tree isn't writable before relocation. This patch introduces the CONFIG_T2080RDB_REV_D option to signal that a board revision D or up is the target. The config option is used to set the correct Aquantia PHY address in the board's u-boot device tree. Defconfig files with the option enable explicitly are added for convenience. Signed-off-by:
Camelia Groza <camelia.groza@nxp.com> Reviewed-by:
-
The T2080RDB boards revisions D and up have updated 10G Aquantia PHYs connected to MAC1 and MAC2. The second Aquantia PHY is located at a different address on the MDIO bus compared to rev C (0x8 instead of 0x1). Fix-up the Linux device tree to update the PHY address for the second Aquantia PHY on boards revisions D and up. Also rename the PHY node to reflect the changes. Signed-off-by:
-
Detect and print the board revision version based on the CPLD registers. Signed-off-by:
-
Both DM_ETH and DM_PCI are enabled for the T2080RDB board. Remove the board_eth_init() callback and the non-DM_ETH code paths since they are not needed anymore. Signed-off-by:
Tom Rini <trini@konsulko.com> Reviewed-by:
-
A system clock of 66MHz was chosen for the pg-wcom-ls102xa. Compared to the Evalboard, this corresponds to a reduction of 1/3. The system counter clock should have been reduced accordingly, but that was not the case, so we had a system time that was 1/3 behind the real time. This patch corrects the system counter clock to 8.333MHz = 66.667MHz / 8. Signed-off-by:
Rainer Boschung <rainer.boschung@hitachi-powergrids.com> Signed-off-by:
Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com> Reviewed-by:
-
This patch adds the front led initialization and the application buffer enable to the eraly board inititlaization. Signed-off-by:
-
In order to improve power consumption ls102x allows to disable peripherals that are not in use. This patch follows SELI8 HW design description and disables peripherals that are not in use in our designs, the same configuration is applicable and for EXPU1. This patch uses available hwconfig option for updating ls102x device disable configuration. Signed-off-by:
-
The default behavior in the latest u-boot revisions is to rotate the active net device to the next available if the requested link is not established. For our ls102x based devices this would mean that if active debug net device is not available, u-boot will rotate and set the next net device that is one of the estar adapters. To return from this situation manual action to set correct ethact adapter will be needed and this can be annoying when working in debug mode. Setting ethrotate=no will disable net adapter rotation and will make sure that the primary adapter is always used. Signed-off-by:
-
This is most probably a typo, and in older u-uboot versions is same as 'saveenv', in the newer uboot versions there is a separate 'save' command that is different from 'saveenv'. Signed-off-by:
-
In our designs we reserve PRAM area at the end of the RAM, and in order this area to be visible and taken into account by the u-boot memory mgmt CONFIG_PRAM has to be defined. Signed-off-by:
-
From production view this is standard test executed during production on all linux based foxmc cards. On CENT2 HW defined memory region is zero means that some DDR accesses are done by memory_post_dataline and memory_post_addrline but pattern tests are skipped that's why mem_regions is fast there. On ls102x for the complete DDR region of 1GiB memory_regions_post_test takes approx. 4min and this is too much for production, so this patch defines only 1MiB region as compromise. Signed-off-by:
-
The EXPU1 design is a new 40G capable ethernet service unit card for Hitachi-Powergrids wired-com product lines. The base SoC is same as for already added SELI8 card, consequently the already added u-boot support for SELI8 is reused. Signed-off-by:
-
Priyanka Jain authored
Add "Priyanka Jain <priyanka.jain@nxp.com>" as MAINTAINER for t102xrdb board. Signed-off-by: -
Priyanka Jain authored
Add "Priyanka Jain <priyanka.jain@nxp.com>" as MAINTAINER for p2041rdb board. Signed-off-by: -
Priyanka Jain authored
Add "Priyanka Jain <priyanka.jain@nxp.com>" as MAINTAINER for p1_p2_rdb_pc board. Signed-off-by: -
Priyanka Jain authored
Add "Priyanka Jain <priyanka.jain@nxp.com>" as MAINTAINER for t4rdb board. Signed-off-by: -
Address and size cells on SOC are set to 1. But gpio nodes are specified with 2 cells. This fixes the gpio nodes to correct cells. Signed-off-by:
Lasse Klok Mikkelsen <lkmi@prevas.dk> Reviewed-by:
Rasmus Villemoes <rasmus.villemoes@prevas.dk> Reviewed-by:
-
Current tsec adapter sets adapter gigabit capabilities by default, and in reality this must not always be the case. It is possible that tsec adapter is used for 100Mbps connection, and in this case setting 1000Mbps capabilities can lead to some side effects such longer autoneg process. In our ls102x designs this problem leads to long autoneg times (> 4 sec) in case board rgmii link is 100Mbps capable only. Limiting the rgmii link capabilities provides faster and smoother link establishment. Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by:
Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: -
Commit df86d324 breaks linux kernel and product application boot. Linux kernel and our product application scripts are expecting 0x prefix for hexadecimal values, while env_set_hex writes them without a prefix. This patch partially revert env_set_hex usage for affected env variables. Signed-off-by:
-
During the mainlining of the board this was by mistake set to sector size. Our user space env scripts are expecting envsize of 0x4000, and setting this differently will break our cross-platform compatibility. Signed-off-by:
-
Drop CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33. CONFIG_FSL_ESDHC_VS33_NOT_SUPPORT is used instead. Signed-off-by:
Yangbo Lu <yangbo.lu@nxp.com> Acked-by: Michael Walle <michael@walle.cc> [for kontron-sl28] Reviewed-by:
-
There is no i.MX board using such option. Drop it. Signed-off-by:
-
For eSDHC, power supply is through peripheral circuit. Some eSDHC versions have value 0 of the bit but that does not reflect the truth. 3.3V is common for SD/MMC, and is supported for all boards with eSDHC in current u-boot. So, make 3.3V is supported in default in code. CONFIG_FSL_ESDHC_VS33_NOT_SUPPORT can be enabled if future board does not support 3.3V. This is also a fix-up for one previous patch, which converted to use IS_ENABLED() for CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 that is not a Kconfig option. Fixes: 52faec31 ("mmc: fsl_esdhc: replace most #ifdefs by IS_ENABLED()") Signed-off-by:
Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by:
-
These boards, according to the schematic and per the board I own, use an M24256-BWDW6TP I2C EEPROM which requires two address bytes. This fixes the 'mac' command which is used to program, among other things, the MAC addresses for the ethernet interfaces on the board. Signed-off-by:
Matt Merhar <mattmerhar@protonmail.com> Reviewed-by:
-
IFC NOR flash base address of ls2088a is 0x580000000, and offset of env crc is 0x500000, so fix the macro CONFIG_ENV_ADDR to fix synchronous exception(access illegal address) Fixes: 59071804 ("configs: ls2080a: Correct ENV_ADDR value") Signed-off-by:
Biwen Li <biwen.li@nxp.com> Reviewed-by:
-
Signed-off-by:
Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by:
-
Add properties related to eMMC HS400 mode for esdhc1. Signed-off-by:
-
Stop to initialize the PCIe controller if it's disabled by RCW. Fixes: 118e58e2 ("pci: layerscape: Split the EP and RC driver") Signed-off-by:
Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by:
-
Read Linux PPFE firmware from flash partition and pass it to Linux through FDT entry. So that we can avoid placing PPFE firmware in Linux rootfs. (FDT may increase at max by 64KB) Signed-off-by:
Chaitanya Sakinam <chaitanya.sakinam@nxp.com> Signed-off-by:
Anji J <anji.jagarlmudi@nxp.com> Signed-off-by:
-
Enable eMMC HS400 workarounds for LX2160A/LX2162A. Signed-off-by:
-
For cpu release command, check whether PSCI is supported firstly, if supported, use PSCI to kick off secondary cores, otherwise still use spin table. Signed-off-by:
Jiafei Pan <Jiafei.Pan@nxp.com> [Fixed checkpatch alignment CHECKs] Signed-off-by:
-
Add check for return value of adjust_vdd() Signed-off-by:
Priyanka Singh <priyanka.singh@nxp.com> Reviewed-by:
-
- Jun 16, 2021
-
-
When using bootefi to boot a EFI binary, u-boot is supposed to provide networking service for EFI application. Currently, 'pfe stop' command is called from bootcmd before running bootefi. As a result network stops working for EFI applications and console is flooded with "Rx pkt not on expected port" messages. Implement board_quiesce_devices() for ls1012a boards and call pfe_command_stop() from it instead of calling 'pfe stop' from *_bootcmd and bootcmd. Tested-by:
Mian Yousaf Kaukab <ykaukab@suse.de> Reviewed-by:
Ramon Fried <rfried.dev@gmail.com> [Fixed checkpatch space error] Signed-off-by:
-
It was noticed that the clock isn't continuously enabled when there is no link. This is because the 125MHz clock is derived from the internal PLL which seems to go into some kind of power-down mode every once in a while. The LS1028A expects a contiuous clock. Thus enable the PLL all the time. Also, the RGMII pad voltage is wrong, it was configured to 2.5V (that is the VDDH regulator). The correct voltage is 1.8V, i.e. the VDDIO regulator. Signed-off-by:
Michael Walle <michael@walle.cc> Reviewed-by:
-
Add required CONFIG_NXP_ESBC for ls1046afrwy to enable ESBC Chain of Trust. Signed-off-by:
Manish Tomar <manish.tomar@nxp.com> Reviewed-by:
-
- Jun 15, 2021
-
-
https://source.denx.de/u-boot/custodians/u-boot-marvellTom Rini authored
- Turris: Fix bootcmd_rescue (Pali)
-
One of the points of putting the rescue boot command into default environment is that user can invoke it without physical access to the board (without having to press the factory reset button), by running run bootcmd_rescue in U-Boot's console. Therefore we have to ensure that bootcmd_rescue is always set to default value, regardless of whether the factory reset button was pressed. Otherwise the variable will be empty for example after upgrade from previous U-Boot. Fixes: ec3784d6 ("arm: mvebu: turris_mox: add support for board rescue mode") Fixes: 176c3e77 ("arm: mvebu: turris_omnia: support invoking rescue boot from console") Signed-off-by:
Pali Rohár <pali@kernel.org> Signed-off-by:
Marek Behún <marek.behun@nic.cz> Reviewed-by:
Stefan Roese <sr@denx.de>
-
- Jun 11, 2021
-
-
https://source.denx.de/u-boot/custodians/u-boot-microblazeTom Rini authored
Xilinx changes for v2021.07-rc5 zynqmp: - Fix ANALOG_BUS value after powerup - Disable EFI_CAPSULE_ON_DISK_EARLY zynqmp-gqspi: - Fix write issue
-
