Alexandru Gagniuc authored 4 years ago and Patrick Delaunay committed 4 years ago

mmc_of_parse() can populate the 'f_max' and 'host_caps' fields of
struct mmc_config from devicetree.
The same logic is duplicated in stm32_sdmmc2_probe(). Use
mmc_of_parse(), which is more generic.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>

Alexandru Gagniuc authored 4 years ago and Patrick Delaunay committed 4 years ago

"cap-mmc-highspeed" enables support for 26 MHz MMC, but there is no
additional flag to enable 52 MHz MMC. In Linux. "cap-mmc-highspeed"
is used for MMC HS at both 26MHz and 52MHz.

Use the same approach and enable MMC_CAP(MMC_HS_52) host capability
when "cap-mmc-highspeed" is found in the devicetree. In the event an
MMC card doesn't support 52 MHz, it will be clocked at a speed based
on its EXT CSD, even on 52 MHz host controllers

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>

Second set of u-boot-atmel features for 2021.01 cycle:

This feature set brings the rework of the clock tree for sam9x60 SoC.
This makes the clock tree fully compatible with Common Clock Framework
and allows full clock configuration in U-Boot. This means that the
sam9x60 boards can boot now using U-Boot.
This also includes the definitions for sam9x60 SiPs and a divisor fix
for the clock on sama7g5 SoC.

This SoC has the 5th divisor for the mck0 master clock.
Adapt the characteristics accordingly.

Reported-by: Mihai Sain <mihai.sain@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>

clk-master can have 5 divisors with a field width of 3 bits
on some products.

Change the mask and number of divisors accordingly.

Reported-by: Mihai Sain <mihai.sain@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>

SAM9X60 SiP (System in Package) are added for SoC identification.

Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>

Use alphabetical order for entries in sam9x60ek-u-boot.dtsi

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>

Update defconfigs for using common clock framework compatible
clocks.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>

Use CCF compatible for PMC. With this, the board/SoC will be
able to boot.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>

Use slow clock CCF compatible DT bindings. This will not break
the above functionality as the SoC is not booting with current
PMC bindings.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>

Use u-boot,dm-pre-reloc for slow xtal and main xtal.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>

Slow Xtal and Main Xtal are board specific. Add their proper
frequency to board file.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>

Add SAM9X60 clock support compatible with CCF.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>

Heap base address is computed based on SYS_INIT_SP_ADDR by
subtracting the SYS_MALLOC_F_LEN value in
board_init_f_init_reserve().

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>

 - add dw-mipi-dsi phy timings and Tx escape clock configuration
 - fix pwm backlight duty cycle calculation
 - migrate CONFIG_VIDEO_BMP_* and CONFIG_BMP_* to Kconfig

Patrick Delaunay authored 4 years ago and Anatolij Gustschin committed 4 years ago

Done with:
./tools/moveconfig.py BMP_16BPP BMP_24BPP BMP_32BPP

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Patrick Delaunay authored 4 years ago and Anatolij Gustschin committed 4 years ago

Done with:
./tools/moveconfig.py VIDEO_BMP_RLE8

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Patrick Delaunay authored 4 years ago and Anatolij Gustschin committed 4 years ago

Done with:
./tools/moveconfig.py VIDEO_BMP_GZIP

The 3 suspicious migration because CMD_BMP and SPLASH_SCREEN
are not activated in these defconfigs:
- trats_defconfig
- s5pc210_universal_defconfig
- trats2_defconfig

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Dario Binacchi authored 4 years ago and Anatolij Gustschin committed 4 years ago

For levels equal to the maximum value, the duty cycle must be equal to
the period.

Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>

Dario Binacchi authored 4 years ago and Anatolij Gustschin committed 4 years ago

The description of the 'max_level' field was incorrectly assigned to the
'min_level' field.

Signed-off-by: Dario Binacchi <dariobin@libero.it>

Neil Armstrong authored 4 years ago and Anatolij Gustschin committed 4 years ago

The Amlogic D-PHY in the Amlogic AXG SoC Family does support a frequency
higher than 10MHz for the TX Escape Clock, thus make the target rate
configurable.

This is based on the Linux commit [1] and adapted to the U-Boot driver.

[1] a328ca7e4af3 ("drm/bridge: dw-mipi-dsi: permit configuring the escape clock rate")

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

Neil Armstrong authored 4 years ago and Anatolij Gustschin committed 4 years ago

The timing values for dw-dsi are often dependent on the used display and
according to Philippe Cornu will most likely also depend on the used phy
technology in the soc-specific implementation.

To solve this and allow specific implementations to define them as needed
add a new get_timing callback to phy_ops and call this from the dphy_timing
function to retrieve the necessary values for the specific mode.

This is based on the Linux commit [1] and adapted to the U-Boot driver.

[1] 25ed8aeb9c39 ("drm/bridge/synopsys: dsi: driver-specific configuration of phy timings")

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

Sean Anderson authored 4 years ago and Tom Rini committed 4 years ago

syslog_test.h is in test/log/, not include/

Fixes: 52d3df7f ("log: Allow LOG_DEBUG to always enable log output")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

- Fix Octeon SPI driver for Octeon TX2
- Fix and enhance Octeon watchdog driver
- Misc minor enhancements to Octeon TX/TX2

- Bring in the next round of dev_xxx cleanup patches.

Sean Anderson authored 4 years ago and Tom Rini committed 4 years ago

Now that linux/compat.h does not define these macros, we do not need to
undefine them.

Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Sean Anderson authored 4 years ago and Tom Rini committed 4 years ago

All users of these functions now include dm/device_compat.h directly.

Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Necessary for dev_xxx.

Signed-off-by: Tom Rini <trini@konsulko.com>

Necessary for dev_xxx.

Signed-off-by: Tom Rini <trini@konsulko.com>

Necessary for dev_xxx.

Signed-off-by: Tom Rini <trini@konsulko.com>

Sean Anderson authored 4 years ago and Tom Rini committed 4 years ago

This driver doesn't use DM (in the correct places), so we use a device and
not a udevice. We also need to include device_compat.h

Signed-off-by: Sean Anderson <seanga2@gmail.com>

Sean Anderson authored 4 years ago and Tom Rini committed 4 years ago

This was included, but was ifdef'd out. We also need dm.h for struct
udevice.

Signed-off-by: Sean Anderson <seanga2@gmail.com>

Sean Anderson authored 4 years ago and Tom Rini committed 4 years ago

This header is necessary for the dev_xxx macros.

Signed-off-by: Sean Anderson <seanga2@gmail.com>

Sean Anderson authored 4 years ago and Tom Rini committed 4 years ago

Necessary for dev_xxx.

Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Sean Anderson authored 4 years ago and Tom Rini committed 4 years ago

Necessary for dev_xxx.

Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Sean Anderson authored 4 years ago and Tom Rini committed 4 years ago

Necessary for dev_xxx.

Signed-off-by: Sean Anderson <seanga2@gmail.com>

Sean Anderson authored 4 years ago and Tom Rini committed 4 years ago

Necessary for dev_xxx.

Signed-off-by: Sean Anderson <seanga2@gmail.com>

Enable WDT command for Octeon TX/TX2 boards.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Suneel Garapati <sgarapati@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>

Suneel Garapati authored 4 years ago and Stefan Roese committed 4 years ago

This patch enhances the Octeon TX/TX2 watchdog driver to fully enable
the WDT. With this changes, the "wdt" command is now also supported
on these platforms.

Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Suneel Garapati <sgarapati@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>

Clock support is needed for all Octeon TX/TX2 boards. This patch selects
CONFIG_CLK so that it is available.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Suneel Garapati <sgarapati@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>