Device tree alignment with Linux kernel v5.13
- ARM: dts: stm32: Add PTP clock to Ethernet controller
- ARM: dts: stm32: enable the analog filter for all I2C nodes in
  stm32mp151
- ARM: dts: stm32: fix usart 2 & 3 pinconf to wake up with flow control
- ARM: dts: stm32: Add wakeup management on stm32mp15x UART nodes
- ARM: dts: stm32: add #clock-cells property to usbphyc node on stm32mp151
- ARM: dts: stm32: Add STM32MP1 I2C6 SDA/SCL pinmux
- ARM: dts: stm32: Rename mmc controller nodes to mmc@
- ARM: dts: stm32: Add additional init state for SDMMC1 pins

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>

Kunihiko Hayashi authored 3 years ago and Tom Rini committed 3 years ago

Add the device tree for Akebi96. Akebi96 is a 96boards certified
development board based on UniPhier LD20.
( https://www.96boards.org/product/akebi96/

 )

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>

Yu-Tung Chang authored 3 years ago and André Przywara committed 3 years ago

ZeroPi is a new board of high performance with low cost
designed by FriendlyElec., using the Allwinner H3 SOC.

ZeroPi features
- Allwinner H3, Quad-core Cortex-A7@1.2GHz
- 256MB/512MB DDR3 RAM
- microsd slot
- 10/100/1000Mbps Ethernet
- Debug Serial Port
- DC 5V/2A power-supply

Signed-off-by: Yu-Tung Chang <mtwget@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Update the H3 DT files from the Linux 5.12 release.

The changes update some boards, and don't affect U-Boot, but fix Gigabit
Ethernet when this DT is passed on to the Linux kernel.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Update the H5 DT files from the Linux 5.12 release.

The changes don't affect U-Boot at all, but fix Gigabit Ethernet when
this DT is passed on to the Linux kernel. It also introduces DVFS.

This also updates the shared sunxi-h3-h5.dtsi, but that only adds nodes
that are of no concern to U-Boot.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Update the H6 DT files from the Linux 5.12 release.

The changes are minimal (many LED node renames), but also help to enable
USB port 0 in U-Boot (later), enable the RSB device (not yet used in
U-Boot), and also introduce an MMC frequency limit.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Stephan Gerhold authored 3 years ago and Tom Rini committed 3 years ago

It looks like SD card detection is broken at the moment for DB410c.
The eMMC is detected correctly, but the SD card is not.

This is probably similar to the issue fixed in commit 85051474
("mmc: msm_sdhci: Use mmc_of_parse for setting host_caps") for eMMC,
except that the SD card does not have a property like "non-removable"
that skips the card detection.

The SDHCI on DB410c cannot detect itself if a SD card is inserted,
so add the necessary cd-gpios to make SD card detection work again.

While at it, fix the #gpio-cells for the soc_gpios to avoid DTC
warnings - the soc_gpios are actually already used with two cells
for the gpio-leds so this was just wrong all the time.

Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

Trevor Woerner authored 3 years ago and Tom Rini committed 3 years ago

Add basic support for running U-Boot on the Embedded Artists LPC3250
Developer's Kit v2 board by launching U-Boot from the board's s1l loader
(which comes pre-installed on the board).

Signed-off-by: Trevor Woerner <twoerner@gmail.com>

Trevor Woerner authored 3 years ago and Tom Rini committed 3 years ago

Import the dtsi, dts, and clock binding files for the lpc32xx ea3250 board
directly and unmodified from the latest Linux kernel.

Signed-off-by: Trevor Woerner <twoerner@gmail.com>

Masami Hiramatsu authored 3 years ago and Tom Rini committed 3 years ago

Add device trees for 96boards EE DeveloperBox and basement SynQuacer
SoC dtsi. These files are imported from EDK2

commit 83d38b0b4c0f240d4488c600bbe87cea391f3922

as-is (except for the changes #include path and some macros).

And add U-Boot specific changes in synquacer-sc2a11-developerbox-u-boot.dtsi

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>

The GPIO polarity for onewire must be GPIO_ACTIVE_HIGH.
On previous versions this used to work as it looks like the right flag values
are being passed since :
https://lists.denx.de/pipermail/u-boot/2020-April/407195.html



And that series broke the old functionality for onewire nodes.
Some boards had the correct value for the polarity, but it wasn't clear
so I replaced it with the right macro for the flag, instead of an empty value.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>

Michael Walle authored 3 years ago and Ramon Fried committed 3 years ago

Now that u-boot gained DSA support, and it is already enabled for the
kontron_sl28 board, add the last missing piece and enable the
corresponding devices it in the device tree.

Signed-off-by: Michael Walle <michael@walle.cc>

Vladimir Oltean authored 3 years ago and Ramon Fried committed 3 years ago

The enetc-2 port is used as DSA master (connected back-to-back to
mscc_felix_port4). Since the convention is to not enable ports in the
common SoC dtsi unless they are used on the board, then enable enetc-2
only when mscc_felix_port4 itself is enabled.

All existing device trees appear to adhere to this rule, so disable
enetc-2 in the SoC dtsi.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

Vladimir Oltean authored 3 years ago and Ramon Fried committed 3 years ago

To comply with the device tree bindings expectations for an Ethernet
controller, as well as to simplify the driver code, declare fixed-link
nodes for the internal ENETC ports (attached to the mscc_felix switch).

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

Vladimir Oltean authored 3 years ago and Ramon Fried committed 3 years ago

There are no PCB trace delays on this board, so the PHY needs to enable
its internal ones in order to have a proper electrical connection to the
enetc MAC.

Fixes: b32e9a75 ("arm: dts: ls1028a updates for network interfaces")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

Vladimir Oltean authored 3 years ago and Ramon Fried committed 3 years ago

Due to an upstream change, the ls1028a.dtsi bindings for the mscc_felix
switch got accepted with all ports disabled by default and with no link
to the DSA master - this needs to be done on a per board basis.

Note that enetc-2 is not currently disabled in the ls1028a.dtsi, but
presumably at some point it might become. Explicitly enable it in the
QDS device trees anyway, to proactively avoid issues when that happens.

Fixes: a7fdac7e ("arm: dts: ls1028a: define QDS networking protocol combinations")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

This patch adds psgtr clocks and phy entry for USB0, USB1 and SATA node for
zc1751-xm017-dc3 board.

Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Add board code for the R8A779A0 V3U Falcon board.

Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
--
Marek: - various small rebase fixes and clean ups

The R-Car V3U does support RPC interface, however the support for it is
missing in upstream Linux DTs as of commit 9f4ad9e425a1 ("Linux 5.12"),
add the node into u-boot.dtsi to let U-Boot access the SPI NOR or HF.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>

Add R8A779A0 V3U DT extras for U-Boot.

Based on "ARM: dts: renesas: Add R8A779A0 V3U DTs"
by Hai Pham <hai.pham.ud@renesas.com>

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>

Import R8A779A0 V3U Falcon DTs from Linux 5.12,
commit 9f4ad9e425a1 ("Linux 5.12") .

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>

Import R8A779A0 V3U DTs and headers from Linux 5.12,
commit 9f4ad9e425a1 ("Linux 5.12") .

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>

DT files have been added this year but forgot to update it that's why do it
in separate patch now.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Wire psgtr for zc1751 dc1 board.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

It is not recommended to have aliases for gpio. In past it was used in
Linux for assigning numbers via sysfs which is deprecated and libgpiod
should be used instead.
In U-Boot this number is used for seq number but gpio offset are not
counted from this number. That's why having these aliases only for seq
number is not needed. As is done in Linux it is the best to use full gpio
name instead of sequence number which depends on sequence in binding.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Both boards are usb3.0 capable. dc3 was also missing enabling dwc3* nodes.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Align USB nodes with the latest dt-bindings. It is adding resets, new
interrupt and also some quirks.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

dtc supports new sugar syntax which is easier compare to previous one
that's why also covert overlays for SOM to it.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

kv260-revB is different compare to revA (usbhub is wired via i2c) that's
why remove revA compatible string.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

psgtr node should be below pinctrl for easier comparion among dts files.
That's why move that nodes to different location.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Clock setting is not static anymore that's why it depends on firmware setup
that's why remove this comment.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Linux kernel is not using these properties that's why they can be removed.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Networking subsystem is not using aliases that's why remove them for CAN
devices. There is also no any other Xilinx ZynqMP DT file with them.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

There are no drivers for these devices that's why remove that nodes
completely. This change is done based on Linux kernel.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/20210308115437.2232847-1-quanyang.wang@windriver.com

Convert all boards to use nvmem alias instead of xlnx,eeprom. The change is
done based on discussion in the link below.

Link: https://lore.kernel.org/r/CAL_JsqLMDqpkyg-Q7mUfw-XH67-v068Q6e9wTq2UOoN=0-_coQ@mail.gmail.com


Signed-off-by: Michal Simek <michal.simek@xilinx.com>

As per the design specification
"The 16-bit Seconds Calibration Value represents the number of
 Oscillator Ticks that are required to measure the largest time
 period that is less than or equal to 1 second.
 For an oscillator that is 32.768 KHz, this value will be 0x7FFF."

Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

psgtr node should be below pinctrl for easier comparion among dts files.
That's why move that nodes to different location.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Historically dpdma and dpsub are placed at the end of files. Move nodes
there for easier comparison among dts files.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

dp_aclk is not used anywhere that's why remove it.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Trivial patch.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>